Product Overview
The Linear Pro Access GSLG-A-223 is part of the GSLG-A Series of industrial and commercial slide gate operators. This series is built for heavier vehicular slide gate openings that need a rugged operator with an integral APeX Controller, direct motor-to-gear-reducer drive, #50 roller chain, C-face brake, emergency manual disconnect, adjustable limit system, and a powder-coated cabinet. The GSLG-A-223 configuration is specifically tied to 1/2 HP 230V three phase service, so it should be selected by the electrical requirements of the site and the operator nameplate, not by the cabinet appearance alone.
In practical field use, a GSLG-A operator is normally found at commercial yards, industrial properties, factories, loading areas, restricted access vehicle entrances, and other slide gate locations where a residential slide operator is not appropriate. Correct selection depends on the full gate system: gate weight, gate length, roller condition, track condition, chain alignment, duty cycle, available voltage, phase, safety device layout, vehicle detection, and access control wiring. The same GSLG-A family includes several horsepower and voltage combinations, and they are not automatic substitutes for one another. When replacing an existing unit, match the full model number, voltage, phase, horsepower, and current site requirements before ordering.
Compatible With
- Linear Pro Access GSLG-A-223 replacement or new-install applications where 1/2 HP 230V three phase is required
- GSLG-A Series commercial / industrial vehicular slide gate operator installations
- Class III industrial / limited access and Class IV restricted access slide gate locations when the complete installation meets applicable safety requirements
- Commercial slide gates using compatible chain drive layout, post mount configuration, and field-installed monitored safety devices
- Access control accessories such as AK-11 keypads, AE-100 telephone entry systems, ACT-22A transmitters, MDT-1A transmitters, AM-RPR proximity receivers, loop detectors, safety photo eyes, safety edges, and vehicle detectors when wired through the proper operator inputs
- Pad-mount applications when the correct optional pad mount hardware and site design are used
- Related GSLG-A horsepower/voltage models only after matching gate size, power supply, phase, control requirements, and current Linear/Nice specifications
Features & Specifications
| Manufacturer | Linear / OSCO / Nice |
|---|
| Product Type | Industrial/commercial slide gate operator |
|---|
| Series | GSLG-A Series |
|---|
| Part Number | GSLG-A-223 |
|---|
| Horsepower | 1/2 HP |
|---|
| Voltage | 230 VAC |
|---|
| Phase | Three Phase |
|---|
| Application | 1/2 HP 230V three phase GSLG-A slide gate installations |
|---|
| Drive | Direct motor to gear reducer drive with #50 roller chain |
|---|
| Controller | Integral APeX Controller |
|---|
| Brake | C-face brake |
|---|
| Gate Speed | Commonly listed at 12 inches per second for the GSLG-A series |
|---|
| Mounting | Post mount standard; pad mount optional on supported installations |
|---|
| Finish | Powder coat finish |
|---|
| Safety | Requires proper monitored safety devices, entrapment protection, warning signs, and code-compliant installation |
|---|
| Notes | Gate capacity ratings and maximum gate length can vary by submittal, generation, and listing source; confirm current manufacturer documentation for the job |
|---|
Also Known As / Related Part Numbers
- GSLG-A-223
- GSLGA223
- Linear GSLG-A-223
- OSCO GSLG-A-223
- Nice Linear GSLG-A-223
- Linear Pro Access GSLG-A-223
- GSLG-A Series
- GSLG-A
- VS-GSLG
- Linear Pro Access GSLG-A
- Linear OSCO GSLG-A
- OSCO GSLG-A
- Nice / Linear GSLG-A
- Related GSLG-A models: GSLG-A-211, GSLG-A-221, GSLG-A-283, GSLG-A-223, GSLG-A-243, GSLG-A-411, GSLG-A-421, GSLG-A-483, GSLG-A-423, GSLG-A-443, GSLG-A-111, GSLG-A-121, GSLG-A-183, GSLG-A-123, GSLG-A-143
Technician Note
Do not select a GSLG-A operator by horsepower alone. The voltage and phase suffix in the model number is critical. A qualified gate technician or electrician should verify site power, disconnect, circuit protection, operator grounding, safety inputs, and control wiring before installation.
Before Ordering Checklist
- Confirm the exact model number: GSLG-A-223
- Verify horsepower, voltage, and phase against the site power and old nameplate
- Confirm gate weight, gate length, roller condition, and track condition
- Review whether the installation requires post mount or optional pad mount hardware
- Confirm monitored photo eyes, safety edges, loops, warning signs, and access controls required for the gate layout
- Check local code, UL325/ASTM safety requirements, and any facility specifications
Professional Advisory
This is high-voltage commercial gate equipment. Installation, service, and diagnosis should be handled by qualified gate and electrical professionals. Do not bypass monitored safety devices, emergency stop controls, or required entrapment protection.
Product Q&A
What voltage and phase is the GSLG-A-223?
The GSLG-A-223 configuration is listed as 1/2 HP, 230 VAC, Three Phase. Match this to the site power and the existing operator nameplate before ordering or replacing an operator.
Can I replace another GSLG-A model with the GSLG-A-223?
Only if the horsepower, voltage, phase, gate size, control layout, and installation requirements match. GSLG-A model numbers are not interchangeable just because the cabinets look similar.
What type of gate is this operator for?
The GSLG-A Series is for commercial and industrial slide gate applications, not swing gates or garage doors. The gate must be properly built, supported, and rolling freely before an operator is installed.
Does this operator include the required safety devices?
Do not assume all required monitored safety devices are included. Photo eyes, safety edges, loops, warning signs, and access controls must be selected for the specific gate layout and current code requirements.
Why does the model number matter so much on GSLG-A operators?
The suffix identifies horsepower, voltage, and phase. Ordering the wrong suffix can create a serious power mismatch and may damage equipment or create an unsafe installation.
[ITEMPRICE]