Linear Pro Access SW2000XLS Replacement Arm with 6' Cable for SW2000XLS Operators
The Linear Pro Access PROSW2000ARMXLS is a primary/single replacement actuator arm for the SW2000XLS swing gate operator family. The actuator arm is the part that physically pushes or pulls the gate leaf through its travel. It works with the control board, brackets, limit setup, battery system, and safety accessories to move the gate smoothly and stop properly at each end of travel.
This arm is commonly replaced when the original actuator has internal wear, impact damage, water intrusion, a cut or pinched cable, broken mounting points, or inconsistent movement. Before replacing the arm, the gate itself should be checked. A gate that drags, sags, binds at the hinges, lacks stops, or has incorrect bracket geometry can damage a new arm quickly.
Correct matching is important. The SW2000XLS family uses specific actuator sizing and cable configurations. A similar-looking arm from another XLS or older XL model may not have the same motor, cable length, travel, or control-board compatibility.
Find Replacement Parts for SW2000XLS
Compatible With
- Linear / GTO Pro Access SW2000XLS swing gate opener systems
- SW2000XLS replacement actuator applications
- primary/single replacement actuator arm locations when the cable length and operator generation match
- Pull-to-open swing gate installations using the correct bracket layout
- Push-to-open swing gate installations when the correct push-to-open bracket is used
- Chain link, tube, panel, ornamental, wood, vinyl, aluminum, and steel swing gates within rating
- Solar-compatible XLS systems when connected to the correct control board and charging setup
Features & Specifications
| Manufacturer | Linear / Nice / GTO Pro Access |
|---|
| Product Type | Replacement swing gate actuator arm |
|---|
| Part Number | PROSW2000ARMXLS |
|---|
| Application | SW2000XLS swing gate opener replacement arm |
|---|
| Role | primary/single replacement actuator arm |
|---|
| Cable Length | 6 ft |
|---|
| Gate Capacity | Commonly associated with 16 ft or 500 lb when correctly installed |
|---|
| Compatible Operator Type | Battery-powered swing gate operator |
|---|
| Notes | Verify arm label, cable length, and operator generation |
|---|
Also Known As / Related Part Numbers
- PRO2000ARMXLS
- PROSW2000ARMXLS
- SW2000XLS arm
- GTO PRO2000ARMXLS
- Linear PRO2000ARMXLS
- PRO2000ARMXLS
Technician Note
This actuator arm should be matched to the exact SW2000XLS system and cable length. If the gate is hard to move by hand, fix the gate hardware before installing the new arm.
Before Ordering Checklist
- Confirm the model number on the old actuator arm
- Confirm cable length and connector condition
- Confirm single, primary, or secondary arm position
- Inspect hinges, brackets, stops, and gate balance
- Check control board, battery, and transformer before condemning the arm
- Do not mix XL and XLS arms unless confirmed by parts diagram
Important Ordering Warnings
- Replacement arms are model and cable-length specific. Do not choose by appearance alone.
Professional Advisory
Heavy gate actuator replacement should be performed with the gate secured and power removed. Use a qualified gate technician if the gate is heavy, unsafe, or the wiring is damaged.
Product Questions & Answers
Is the PROSW2000ARMXLS a complete gate opener kit?
No. The PROSW2000ARMXLS is a replacement actuator arm for an existing compatible SW2000XLS system, not a complete operator kit with control box and accessories.
What cable length is used on this arm?
This arm is commonly listed with a 6 ft cable. Cable length is one of the main fitment details to confirm before ordering.
Can this arm be used on a different XLS model?
Only when the manufacturer parts diagram confirms it. SW2000XLS, SW2002XLS, SW3000XLS, SW3200XLS, SW4000XLS, and SW4200XLS arms are not universal.
What causes a replacement arm to fail?
Common causes include worn internal drive parts, water intrusion, damaged cable, bent mounting geometry, gate binding, poor hinges, or operating a gate beyond the rated size.
Should the gate be checked before installing the arm?
Yes. The gate should swing freely by hand, have good hinges, proper stops, and correct bracket geometry before the new actuator is installed.
