Linear Pro Access SW3000XLS Swing Gate Opener
The Linear PRO-SW3000XLS Single Swing Gate Opener is part of the Linear Pro Access / GTO Pro XLS swing gate operator family. This product is used for vehicular swing gate automation where a linear actuator arm opens and closes the gate leaf from a low-voltage control system. It is commonly installed on residential driveways, estate gates, ranch entrances, farm gates, and lighter commercial vehicle entrances where the gate is within the rated length and weight.
The 3000XLS family is built around a 12 VDC operator platform and is commonly paired with battery backup, AC charging, solar charging, transmitters, keypads, exit devices, and compatible safety equipment. Fitment should be checked by the exact model number and by the role of the arm in the system. A primary operator, a secondary operator, and a dual-gate kit are related, but they are not the same item. The secondary arm depends on the master control box, and the dual system depends on the correct primary/secondary combination.
Correct gate condition is just as important as the operator model. The gate should swing freely by hand, have solid hinges, proper stops, correct bracket geometry, and the required entrapment protection. A heavy, wind-loaded, sagging, or binding gate can overload a properly sized operator and cause nuisance obstruction events or premature wear. For older installations, also confirm whether the original equipment is XL or XLS because generation differences can affect brackets, boards, rev-counter components, and service parts.
Accessories Included
- Battery Backup
- 318 MHz Radio Receiver
- Entry Transmitter
- AC Transformer
- Mounting hardware
Compatible With
- Single vehicular swing gates up to 16 ft. and 650 lb. when properly installed
- Dual gate systems when paired with PRO-SW3200XLS second operator arm
- Linear / GTO Pro SW3000XLS and SW3200XLS XLS family applications
- Common accessories include RB741/FM135 transmitters, RB742 transmitters, keypads, compatible receivers, FM144 gate lock, exit wands, solar panels, batteries, and required safety devices
- Pull-to-open installations with standard hardware and push-to-open installations when correct push-to-open bracket hardware is used
- Common gate materials include tube, chain link, ornamental, wood, vinyl, steel, and aluminum when the gate moves freely
Features & Specifications
| Manufacturer | Linear / GTO Pro / Linear Pro Access |
|---|
| Product Type | Single swing gate opener |
|---|
| Part Number | PRO-SW3000XLS |
|---|
| Series | 3000XLS / 3200XLS swing gate operator family |
|---|
| Voltage | 12 VDC operator system |
|---|
| Application | Vehicular swing gates |
|---|
| Maximum Gate Rating | 16 ft. / 650 lb. |
|---|
| Gate Speed | Commonly listed around 15 to 18 seconds depending on installation |
|---|
| Dual Gate Use | Requires PRO-SW3200XLS second operator for dual-gate use |
|---|
| Solar Compatible | Yes, when properly configured with compatible charging equipment |
|---|
| Safety Monitoring | Requires proper entrapment protection for the installation |
|---|
| Notes | Confirm primary vs secondary arm, XL vs XLS generation, gate geometry, and accessory compatibility |
|---|
Also Known As / Related Part Numbers
- PRO-SW3000XLS, SW3000XLS, GTO PRO-SW3000XLS, Linear PRO-SW3000XLS, Nice Linear PRO-SW3000XLS, PRO-SW3200XLS second operator, SW3000XLS/3200XLS dual system, PRO-SW3002XLS dual kit reference
- Linear 3000XLS swing gate opener
- GTO Pro 3000XLS swing gate opener
- Linear Pro Access 3000XLS gate operator
Technician Note
On XLS swing operators, do not mix up the primary arm, secondary arm, and dual-kit references. If replacing an existing arm, confirm the label on the arm and control box, the cable length, the bracket layout, and whether the system is a 3000XLS or 4000XLS setup. A gate that does not move freely by hand should be repaired before installing or replacing the operator.
Before Ordering
- Confirm the exact operator model and whether the part is primary, secondary, or dual-system related.
- Measure each gate leaf and estimate the actual gate weight.
- Inspect hinges, gate stops, posts, bracket positions, and gate swing clearance.
- Confirm pull-to-open or push-to-open layout and any special bracket requirements.
- Verify batteries, transformer or solar charging setup, receiver, remotes, keypad, gate lock, exit device, and safety devices.
Professional Advisory
Gate operators can create serious pinch, crush, and entrapment hazards if installed incorrectly. Use the required monitored safety devices and follow the operator instructions. Electrical wiring, unsafe gate movement, or safety-device faults should be handled by a qualified gate technician.
Product Q&A
What gate size is the PRO-SW3000XLS used for?
The 3000XLS family is commonly listed for swing gate leaves up to 16 ft. long and 650 lb. Actual fit depends on gate balance, hinges, wind exposure, post geometry, and installation layout.
Is PRO-SW3000XLS the same as the 4000XLS family?
No. The 3000XLS family is rated for smaller/lighter gate leaves than the 4000XLS family. Do not substitute 3000XLS and 4000XLS arms or kits without confirming the parts diagram and system requirements.
Can PRO-SW3000XLS be used for push-to-open gates?
Push-to-open installations may be possible only with the correct push-to-open brackets and proper gate geometry. The bracket setup must be confirmed before ordering or installing.
What accessories are commonly used with PRO-SW3000XLS?
Common accessories include compatible RB741/FM135 or RB742 transmitters, keypads, receivers, gate locks, batteries, solar panels, exit devices, photo eyes, and safety edges matched to the control system.
What should be checked before replacing an XLS operator arm?
Check the exact model number, primary versus secondary arm position, cable length, bracket style, control board, gate size, and whether the old unit is XL or XLS. Similar-looking arms may not be interchangeable.
