Linear Pro Access SW4200XLS Secondary Swing Gate Opener
The Linear Pro Access PRO-SW4200XLS is the matched secondary operator for a dual swing gate installation built around the PRO-SW4000XLS primary operator. In a dual system, the primary side contains or connects to the control equipment, while the secondary arm drives the opposite gate leaf and must be wired, timed, and sequenced correctly with the master side.
This part is commonly ordered when the secondary actuator has physical damage, water intrusion, cable damage, worn internal drive components, or when a single SW4000XLS installation is being expanded into a properly matched dual swing gate setup. The SW4200XLS is part of the higher-capacity 4000XLS family, so it should not be substituted with a smaller SW2000XLS, SW3000XLS, or older XL arm unless the manufacturer parts diagram confirms the change.
Correct fitment matters because the cable length, motor size, arm travel, bracket geometry, and control board programming all affect gate timing and safety operation. For heavy gates, check hinge condition, gate balance, and stopping hardware before blaming the operator arm alone.
Compatible With
- Linear PRO-SW4000XLS primary swing gate operator
- Linear PRO-SW4200XLS dual swing gate secondary operator installations
- GTO / Linear Pro Access SW4000XLS and SW4200XLS dual swing gate systems
- Select 4000XLS residential and light commercial dual swing gate applications
- Wood, steel, aluminum, chain link, tube, panel, ornamental, and vinyl swing gates when within operator limits
- Pull-to-open installations and push-to-open installations when the correct brackets are used
- Solar-assisted XLS systems when paired with the proper control board, battery, and charging equipment
Features & Specifications
| Manufacturer | Linear / Nice / GTO Pro Access |
|---|
| Product Type | Secondary swing gate operator arm |
|---|
| Part Number | PRO-SW4200XLS |
|---|
| Application | Second operator for PRO-SW4000XLS dual swing gate systems |
|---|
| Compatible Operator Type | Dual swing gate opener |
|---|
| Cable Length | 50 ft power cable commonly associated with this secondary operator |
|---|
| Gate Capacity | Used with SW4000XLS family applications up to 20 ft or 1000 lb per leaf when properly installed |
|---|
| Voltage | 12 VDC operator system |
|---|
| Notes | Not a standalone single gate opener |
|---|
Also Known As / Related Part Numbers
- PRO-SW4200XLS
- PROSW4200XLS
- SW4200XLS
- PRO 4200 XLS
- GTO PRO-SW4200XLS
- Linear Pro Access SW4200XLS
- Nice Linear SW4200XLS
- PRO4200ARMXLS related replacement arm reference
- SW4000XLS secondary operator reference
Technician Note
Use this part only as the matched second operator for a PRO-SW4000XLS dual gate layout. A secondary arm with the wrong cable length or wrong generation can create timing, travel, or wiring problems.
Before Ordering Checklist
- Confirm the existing primary operator is PRO-SW4000XLS or the correct 4000XLS control system
- Verify the old secondary operator label before ordering
- Confirm whether the gate is pull-to-open or push-to-open
- Check that the gate leaf is within the 4000XLS weight and length limits
- Inspect hinges, brackets, stops, and cable routing for damage
- Do not mix XL and XLS components unless the parts diagram supports it
Important Ordering Warnings
- This is a secondary operator, not a complete primary control box kit.
- Do not substitute this part for SW2000XLS, SW3000XLS, SW3200XLS, or older XL arms without parts verification.
Professional Advisory
Gate operator electrical troubleshooting, arm replacement on heavy gates, and safety device work should be handled by a qualified gate technician. Never bypass monitored safety devices or operate a gate with unsafe movement.
Product Questions & Answers
Is the PRO-SW4200XLS a complete single gate opener?
No. The PRO-SW4200XLS is the second operator used with a PRO-SW4000XLS primary operator for a dual swing gate system.
What cable length is included with the SW4200XLS secondary operator?
The SW4200XLS secondary operator is commonly supplied with a 50 ft power cable for reaching the control box side of a dual gate installation.
Can this be used with a SW2000XLS or SW3000XLS system?
No. It is matched to the SW4000XLS operator family. The SW2000XLS and SW3000XLS families use different matched secondary operators.
What gate size is this secondary operator normally associated with?
When paired correctly with the SW4000XLS system, it is commonly used on dual swing gates with leaves up to 20 ft or 1000 lb per leaf when the gate and hinges are suitable.
Can this operator be used for push-to-open gates?
Push-to-open installations normally require the correct push-to-open bracket for each operator and must follow the operator manual and safety requirements.
