Product Details
The MMTC PBS-2 NEMA 1 Two-Button Interior Surface Mount Control Station is a NEMA 1 two button interior surface mount control station built for interior surface-mounted two-button station for separate open and close commands where a STOP button is not required at that location. In the field, these MMTC stations are used anywhere a technician needs a dedicated wall station or keyed command point for an automatic gate, commercial overhead door, rolling door, shutter, or similar controlled opening. The station is not the operator itself; it is the customer-facing control device that sends command signals to the operator control board or control panel.
Correct fitment matters because push-button stations can look similar while using different mounting boxes, enclosure ratings, button counts, STOP contact logic, lockout styles, and cylinder formats. A three-button OPEN-CLOSE-STOP station normally has separate conductors for each function, and many commercial operators expect the STOP button to be wired as a normally closed circuit. Replacing a station with the wrong contact arrangement can cause the operator to ignore commands, hold the stop circuit open, or fail to run. For lockout models, the key switch must also be matched to how the original station disabled or enabled the control circuit.
This part is commonly ordered when an existing MMTC station is broken, weathered, missing its proper enclosure, has damaged buttons, or needs to match a facility standard for interior, exterior, flush-mount, surface-mount, or keyed-access control. Always compare the original MMTC part number, the station layout, the wiring diagram, and the physical mounting before replacing it.
Compatible With
This MMTC control station may be used with select commercial door, gate, and access-control systems when the equipment is designed for the same button functions and dry-contact control logic. Compatibility depends on the operator wiring diagram, not only the brand name.
- Commercial door and gate controls with separate OPEN and CLOSE low-voltage command inputs
- interior surface-mount stations replacing a matching two-button MMTC PBS-2 style station
- rolling doors, sectional doors, shutters, or access-control equipment where two normally open momentary contacts are specified
- gate operator command inputs where open and close commands are separated by the control board
- applications where stop control is handled elsewhere or built into the operator according to code and wiring requirements
- LiftMaster/Chamberlain commercial door controls when the terminal strip calls for matching dry-contact wall station inputs
- Linear/OSCO/Nortek, Genie, Overhead Door, Raynor, Manaras, Marantec, and similar commercial operator controls when the wiring diagram matches
- DoorKing, FAAC, HySecurity, Viking, Linear, All-O-Matic, Ramset, and similar gate operators when low-voltage command terminals match the station contact logic
Features & Specifications
| Manufacturer | MMTC |
|---|
| Part Number | PBS-2 |
|---|
| Product Type | NEMA 1 two button interior surface mount control station |
|---|
| Application | interior surface-mounted two-button station for separate open and close commands where a STOP button is not required at that location |
|---|
| Button Functions | Open and Close |
|---|
| Mounting Style | Surface mount |
|---|
| Enclosure / Rating | Metal housing; NEMA 1 interior |
|---|
| Contact Logic | Normally open momentary contacts for open/close style command wiring |
|---|
| Lockout / Cylinder | No lockout; None |
|---|
| Electrical Rating Notes | Commonly referenced at 5 amp at 120 VAC, 240 VAC max general purpose; verify control circuit |
|---|
| Dimensions | 4-1/16 in H x 2-3/8 in W x 1-13/16 in D |
|---|
| Important Notes | Match the operator control terminals, wiring diagram, contact logic, and mounting requirements before ordering. |
|---|
Also Known As / Related Part Numbers
- PBS-2
- MMTC PBS-2
- PBS2
- P-BS-2
- two button surface mount station
- OPEN CLOSE surface control
- related MMTC PBS-1 one-button station
- related MMTC PBS-3 three-button station
- related MMTC 2BF flush-mount two-button station
Technician Note
Do not choose this station by housing appearance alone. Match the existing part number, contact arrangement, STOP circuit logic, enclosure rating, mounting depth, conduit entry, and lockout or cylinder type. If the operator uses monitored safety devices or a specific control-board input sequence, keep those requirements intact.
Before Ordering Checklist
- Confirm the MMTC part number on the existing station or project submittal.
- Match interior versus exterior use and flush-mount versus surface-mount construction.
- Confirm the number of buttons and the exact control functions required.
- Verify normally open and normally closed contact requirements, especially the STOP circuit.
- For lockout models, verify standard, Best/equivalent, or mortise cylinder requirements.
- Compare faceplate, back-box, and enclosure dimensions before replacing an installed station.
- Have a qualified technician handle unfamiliar wiring, line-voltage circuits, or unsafe door/gate movement.
Professional Advisory
A control station should never be used to bypass a required safety device, stop circuit, photo eye, sensing edge, or entrapment-protection input. If the door or gate moves unexpectedly, will not stop, or has damaged wiring, shut the system down and have it inspected by a qualified gate or commercial door technician.
Product Questions & Answers
What is the MMTC PBS-2 used for?
The MMTC PBS-2 is used as a NEMA 1 two button interior surface mount control station for interior surface-mounted two-button station for separate open and close commands where a STOP button is not required at that location. It provides open and close control functions when connected to a compatible operator or control panel.
Is the MMTC PBS-2 a universal control station?
It is broadly usable with many commercial door and gate controls that accept matching dry-contact inputs, but it is not selected by brand alone. The contact logic, button functions, enclosure style, dimensions, and wiring diagram must match the equipment.
Does the MMTC PBS-2 include a lockout?
No lockout. If the control station uses a cylinder or keyed lockout, match the cylinder format and the way the lockout is wired into the operator control circuit.
Can this control station be used outdoors?
This item is listed for NEMA 1 interior. Interior NEMA 1 stations should not be installed in wet or exposed locations. Exterior stations still need proper mounting, conduit entry, sealing, and code-compliant wiring.
What should be checked before replacing an MMTC PBS-2?
Check the part number on the existing station, button count, faceplate or box dimensions, contact type, STOP circuit logic, lockout/cylinder style, and the operator wiring diagram. A qualified technician should handle unsafe or line-voltage wiring.
