Mighty Mule FM350 Parts - FTMT5030 Front Mount w/pin Silver
The FTMT5030 is the front mount repair part used at the gate end of selected Mighty Mule, GTO and Linear PRO swing gate operator arms. This hardware forms the connection point where the operator transfers push and pull force into the gate. A worn, bent or loose front mount can cause sloppy gate movement, clunking at start and stop, poor alignment, binding, or extra stress on the opener arm.
This part is commonly sold as a silver front mount with pin and is used across several Mighty Mule and GTO residential arm families. Because these operators rely on correct geometry between the post bracket, opener arm and gate bracket, replacing the front mount with the wrong style can change the pivot point and create travel problems.
Customers often order FTMT5030 after the clevis area is worn, the pin hole is elongated, the hardware is missing from a used arm, or the original mount has corroded in outdoor service. Inspect the gate bracket, post bracket and arm pivot at the same time because worn hardware in one location often causes wear in the others.
Compatible With
The FTMT5030 front mount is commonly associated with these swing gate opener families, subject to model and generation verification:
- Mighty Mule FM250 swing gate opener
- Mighty Mule FM350 and FM352 swing gate openers
- Mighty Mule FM500 and FM502 swing gate openers
- Mighty Mule FM600 swing gate opener
- Mighty Mule MM500 and MM502 related arm families where this mount matches
- GTO / Linear PRO SW3000 and 3200 series references where specified
- GTO / Linear PRO 2500, 2550 and 1500 series references where specified
- Not a universal front mount for every Mighty Mule, GTO, Linear, or newer smart operator arm
Features & Specifications
| Manufacturer | GTO / Linear PRO / Mighty Mule family |
|---|
| Product Type | Front mount with pin |
|---|
| Part Number | FTMT5030 |
|---|
| Application | Gate-side swing opener arm mounting repair |
|---|
| Compatible Operator Type | Select linear arm swing gate openers |
|---|
| Material / Finish | Metal, silver finish |
|---|
| Included Components | Front mount with pin where supplied by manufacturer |
|---|
| Notes | Confirm pivot style and arm model before ordering |
|---|
Also Known As / Related Part Numbers
- FTMT5030
- LIN-FTMT5030
- GTO FTMT5030
- Mighty Mule FTMT5030
- front mount with pin
- silver front mount
- FM350 front mount
- FM500 front mount
- FM502 front mount
Technician Note
A loose front mount can be a symptom of gate movement or bracket misalignment. Check the gate hinges and bracket spacing before installing a new mount.
Before Ordering Checklist
- Confirm the opener arm model before ordering.
- Compare the old front mount, pin size and pivot style to FTMT5030.
- Inspect the gate bracket and clevis pin area for wear.
- Check that the gate swings freely and does not sag at the hinge side.
- Replace missing clips, washers or worn hardware that may have caused the mount to fail.
Important Ordering Warnings
Some newer Mighty Mule models and older GTO models use similar-looking hardware. Do not order by appearance alone if the operator model or arm generation is unknown.
Professional Advisory
If the mount is bent from impact or the gate is hard to move by hand, correct the gate condition before installing the replacement hardware.
Product Questions & Answers
Where does the FTMT5030 front mount install?
It installs at the gate end of select swing gate opener arms and connects the opener arm to the gate-side bracket area.
Which Mighty Mule models commonly use FTMT5030?
It is commonly listed for FM250, FM350, FM352, FM500, FM502 and FM600 style operators, along with related MM500/MM502 family arms where the mount matches.
Can a worn front mount cause noisy gate movement?
Yes. A worn or loose mount can create clunking, extra play, uneven movement and stress on the operator arm.
Is FTMT5030 the same as the full bracket kit?
No. FTMT5030 is the front mount with pin. Full hardware bracket sets or hardware bags are separate parts.
Should I replace the pin and clips when replacing the mount?
If the pin, washers or retaining clips are worn, missing or corroded, they should be replaced so the new mount is properly secured.
