Products [14]
Base Loop Detectors
BASE Loop Detectors, Vehicle Detectors & Gate Loop Sensors
BASE loop detectors are used with automatic gate operators, parking systems, barrier arms, access control lanes, and vehicle entry points where the system needs to detect a vehicle over an in-ground loop. At Gate Openers Unlimited, this page helps customers shop BASE inductive loop vehicle detectors, low-voltage and high-voltage detector models, safety loop detectors, exit loop detectors, harnesses, and related vehicle detection accessories.
When choosing a BASE loop detector, the most important details are the model number, voltage range, socket style, loop function, relay output, and how the detector is being used in the gate or parking system. A detector used for a free-exit loop may not be set up the same way as one used for a safety loop, shadow loop, arming loop, or presence detection application.
BASE Vehicle Detection Products
BASE loop detectors are commonly used in gate and access control systems to detect vehicles through an inductive loop installed in the driveway or roadway. When a vehicle enters the loop field, the detector sends a signal to the gate operator, access control panel, or parking equipment depending on how the system is wired.
These detectors are often used for automatic gate exit loops, safety loops, reversing loops, shadow loops, barrier arm systems, commercial entry lanes, apartment gates, gated communities, storage facilities, parking garages, and other controlled vehicle access points. The correct BASE detector depends on the voltage available, loop setup, detector socket, and the function the loop is expected to perform.
Shop BASE Loop Detectors by Product Type
- Inductive loop vehicle detectors
- Exit loop detectors
- Safety loop detectors
- Low-voltage loop detectors
- High-voltage loop detectors
- Solar-compatible low-power loop detectors
- Single-channel loop detectors
- Loop detector harnesses
- Vehicle detection accessories for gate and parking systems
Common BASE Loop Detector Models
| Model Family | Common Use | Ordering Notes |
|---|---|---|
| BASE LD-1500 | Low-power vehicle detection, often considered for solar or low-power gate applications | Verify power requirements, loop function, and whether the detector is being used for exit, safety, or presence detection. |
| BASE LD-100 | Single-channel inductive loop detection for gate and access control applications | Confirm HV or LV version, operating voltage, relay output, and socket or harness style before ordering. |
| BASE LD-200 | Vehicle detection for exit loops, safety loops, and access control lanes | Match the detector voltage, loop setup, and system wiring. Do not assume HV and LV models are interchangeable. |
| BASE LD-1150 | Inductive vehicle detection for gate, parking, and access control systems | Check model suffix, voltage range, and whether the detector is being used as a safety, exit, or presence detector. |
| BASE LD-1250 | Vehicle detection for controlled access, parking, and gate operator systems | Verify HV or LV version, output needs, and loop configuration before replacing an existing detector. |
| BASE LD-1800 | Vehicle detection for select gate and access control applications | Confirm model number, voltage, socket compatibility, and system function before ordering. |
| BASE Harnesses | Connection harnesses for compatible 11-pin box-style loop detectors | Match the harness style to the detector model and control panel wiring before installation. |
How to Choose the Right BASE Loop Detector
Start by identifying the detector’s job in the system. A loop detector may be used to open a gate for exiting vehicles, hold a gate open while a vehicle is in the path, prevent a gate from closing on a vehicle, provide presence detection, or work with a parking or access control system. Once the function is clear, match the detector by model number, voltage, and wiring style.
- For exit loops: choose a detector suited for free-exit vehicle detection and confirm the relay output works with the gate operator input.
- For safety loops: verify that the detector is wired to the proper safety or reverse input and that the gate operator’s required entrapment protection is not bypassed.
- For solar gate systems: consider low-power models when power draw matters, but still confirm voltage and system compatibility.
- For replacement detectors: match the existing BASE model number, HV/LV version, socket style, and wiring before ordering.
- For parking and barrier systems: confirm the detector output, loop layout, relay function, and controller input requirements.
Before Ordering BASE Loop Detectors
- Confirm the exact BASE model number on the existing detector.
- Check whether the detector is an HV or LV version.
- Verify the available voltage, such as low-voltage gate power or line-voltage applications.
- Confirm whether the detector is used for exit, safety, shadow, arming, or presence detection.
- Check the socket style, harness, terminal wiring, and relay output requirements.
- Inspect the loop condition if the existing detector is giving loop fault, intermittent detection, or false detection issues.
- Confirm the loop wire, saw-cut loop, lead-in wire, and splice condition before assuming the detector is the only failed part.
- For gate safety applications, make sure required monitored safety devices and entrapment protection are installed and working properly.
BASE Compatibility and Fitment Notes
BASE loop detector compatibility depends on the model number, voltage version, detector socket, relay output, loop wiring, and how the detector is connected to the gate operator or access control equipment. Similar-looking detectors may have different voltage ranges, output behavior, or wiring requirements.
When replacing a failed detector, do not rely only on the product appearance. Match the complete model number and check whether the existing detector is high voltage, low voltage, solar compatible, single-channel, or designed for a specific loop function. If the detector plugs into an 11-pin socket or uses a harness, confirm the pinout and wiring before replacing it.
If the loop detector is part of a gate safety circuit, vehicle entrapment protection setup, commercial gate operator, parking system, or high-voltage control panel, have a qualified gate technician verify the wiring and system operation. Do not bypass safety loops, monitored safety devices, photo eyes, reversing edges, or other required protection devices.
Related BASE Loop Detector and Vehicle Detection Categories
- Vehicle Detection
- Loop Detectors
- Exit Loop Detectors
- Safety Loop Detectors
- Gate Safety Devices
- Gate Opener Parts
- Access Control
- Commercial Gate Operator Accessories
- Barrier Arm Accessories
- Loop Wire and Detection Accessories
South Florida Local Pickup
Gate Openers Unlimited is located in South Florida and offers local pickup from our Hialeah Gardens warehouse when available. This is helpful for local gate technicians, installers, property managers, HOAs, parking facility operators, and commercial buyers who need BASE loop detectors, harnesses, or related vehicle detection parts without waiting on standard shipping. Please confirm availability before heading to the warehouse.
BASE Loop Detectors FAQ
What are BASE loop detectors used for?
BASE loop detectors are used to detect vehicles in gate, parking, barrier arm, and access control systems. They are commonly used for free-exit loops, safety loops, shadow loops, arming loops, and vehicle presence detection.
What is the difference between an exit loop and a safety loop?
An exit loop is usually used to open a gate when a vehicle leaves the property. A safety loop is used to help prevent the gate from closing while a vehicle is in the gate path. The detector, wiring, and gate operator input must be set up correctly for the intended function.
What does HV and LV mean on BASE loop detectors?
HV generally refers to high-voltage models, while LV generally refers to low-voltage models. The correct choice depends on the available power and the gate or access control system. Always verify the voltage rating before ordering a replacement.
Can I replace a BASE high-voltage detector with a low-voltage detector?
Not unless the power supply, wiring, and system design support the low-voltage model. High-voltage and low-voltage detectors are not automatically interchangeable. Match the existing model number and voltage requirements before ordering.
Is the BASE LD-1500 a good choice for solar gate operators?
The BASE LD-1500 is commonly associated with low-power vehicle detection and may be considered for select solar or low-power gate applications. Verify the gate operator voltage, loop function, and system requirements before ordering.
Why is my loop detector not detecting vehicles?
A loop detector problem can be caused by the detector, loop wire, lead-in wire, bad splices, incorrect sensitivity, wiring issues, power problems, or a fault in the gate operator input. Check the full loop circuit before assuming the detector is the only failed part.
Are BASE loop detectors universal?
No. BASE loop detectors must be matched by model, voltage, socket style, relay output, and system function. Some models may work in many gate and access control applications, but they should still be verified before ordering.
Do BASE loop detectors require professional installation?
Many replacements are straightforward for trained gate technicians, but loop detector wiring, high-voltage circuits, safety loops, and commercial gate systems should be handled by a qualified technician. Required safety devices should never be bypassed.
