GTO PRO SW2000XLS / SW2002XLS Series Replacement Parts

GTO PRO RB502 Transformer - 14 Volt - AC - Operator Only - PRO/1000/1200

GTO RB502 Transformer - 14 Volt - AC - Operator Only - PRO/1000/1200

$39.99

(4)

Add to Wish List

Add To Cart

GTO SW2000 Parts - H101P Hardware BAG for 3000XL - 2000XL series and 2500 (includes R4027)

$24.95

Add to Wish List

Add To Cart

GTO PRO 1500 Parts - 347IH Bracket / 11 inch Post Pivot - Push-To-Open (SW3000/3200/2500/2550/1500*)

GTO 1500 Parts - 347IH Bracket / 11 inch Post Pivot - Push-To-Open (SW3000/3200/2500/2550/1500*)

$43.05

Add to Wish List

Add To Cart

GTO SW2000XLS Replacement Arm with 6' Cable for SW2000XLS Operators

$549.95

Not for Sale

(4)

Add to Wish List

GTO R4722 - Replacement Control Board for SW2000XLS & SW2002XLS Gate Openers

$424.95

(27)

Add to Wish List

Add To Cart

GTO Rev Counter Board (SW2000XLS Series)

$48.45

(11)

Add to Wish List

Add To Cart

GTO Bracket, 11" Post Pivot, Push-To-Open (SW2000XL(S)/2500/2550/1500)

$43.05

Add to Wish List

Add To Cart

GTO Silver bracket set w/ captured gate bracket

$39.95

(1)

Add to Wish List

Add To Cart

GTO Front Mount (SW2000XLS Series, SW3000XLS Series)

GTO / Linear R4886 Front Mount (SW2000XLS Series, SW3000XLS Series)

$44.95

Add to Wish List

Add To Cart

GTO Black 2000XLS/3000XLS/4000XLS Scraper Seal Kit

$34.99

Add to Wish List

Add To Cart

GTO 2000XL(S) Housing Kit Black

$133.01

(1)

Add to Wish List

Add To Cart

GTO PRO / Mighty Mule Replacement Alarm - Buzzer

$9.95

Not for Sale

(9)

Add to Wish List

Linear Pro Access R4722 - Replacement Control Board for SW2000XLS & SW2002XLS Gate Openers

$424.95

(3)

Add to Wish List

Add To Cart

Linear Pro Access SW2000XLS Replacement Arm with 6' Cable for SW2000XLS Operators

$549.95

Not for Sale

(4)

Add to Wish List

Linear Pro Access SW2002XLS Replacement Arm with 32' Cable for SW2002XLS Operators - Secondary Arm Only

$574.95

Not for Sale

(2)

Add to Wish List

GTO R5722 - Replacement Control Board for SW2000XLS & SW2002XLS Gate Openers

$424.95

(3)

Add to Wish List

Add To Cart

Frequently Asked Questions : GTO PRO SW2000XLS / SW2002XLS Series Replacement Parts

Q1: What are the primary power requirements for the GTO PRO SW2000XLS and SW2002XLS series?

A1: These systems operate on a 12-volt DC battery-based platform. The battery is maintained by either an AC plug-in transformer or a compatible solar panel integration. Consistent voltage levels are required to ensure the control board and motor function within manufacturer specifications.

Q2: How can the correct replacement control board be identified for these models?

A2: Identifying the proper replacement board requires locating the specific part number or revision code printed directly on the existing circuit board. Because hardware generations can vary, it is necessary to verify this information against the manufacturer's technical manual to ensure compatibility with existing accessories and safety sensors.

Q3: Can a damaged linear actuator arm on the SW2000XLS or SW2002XLS be repaired?

A3: Internal mechanical failures or physical damage to a linear actuator arm typically require a complete component replacement rather than a repair. Attempting to open the sealed actuator can compromise weatherproofing and internal gearing. A qualified local professional should be consulted for proper installation and travel calibration.

Q4: What is the main difference between parts for the SW2000XLS and the SW2002XLS?

A4: The SW2000XLS is a single gate operator system, while the SW2002XLS is the dual gate version. Most primary components like the control board and actuator arms are interchangeable, but the SW2002XLS requires an additional secondary actuator and a specific communication cable to synchronize the two gate leaves.

Q5: What role do limit switches play in the operation of the XLS series?

A5: Limit switches dictate the exact stopping points for the gate in both the open and closed positions. If the gate is over-traveling or failing to close completely, the limit switches may require replacement or recalibration. All mechanical adjustments should be performed according to the steps outlined in the manufacturer's installation manual.

Q6: Is the GTO PRO XLS series compatible with solar power charging?

A6: Yes, these models feature an integrated charging circuit that supports solar power integration for battery maintenance. To convert a system to solar, the AC transformer must be removed and a compatible solar panel wired to the designated terminals. Review the manufacturerâ€™s solar sizing chart to determine the required wattage for your application.

Q7: What should be done if the remote transmitters stop responding to the receiver?

A7: Communication issues are often caused by depleted transmitter batteries, signal interference, or a malfunctioning receiver module. First, verify the battery levels in the remotes and ensure the receiver antenna is properly positioned. For complex frequency troubleshooting or reprogramming, refer to the manufacturerâ€™s technical documentation.

Q8: Why is the maintenance of safety photo eye sensors critical for these operators?

A8: Safety photo eye sensors project an infrared beam across the gate path to provide entrapment protection. If an obstacle breaks this beam while the gate is closing, the operator will stop and reverse direction. Functional and aligned sensors are a critical requirement for compliance with UL 325 safety standards.

Q9: Why might the pivot arm brackets require replacement over time?

A9: Prolonged environmental exposure and the stress of heavy gate cycles can cause metal pivot brackets to rust, bend, or crack. Damaged brackets alter the geometry of the gate travel, placing severe strain on the actuator and motor. Installation of replacement brackets often requires precise alignment or welding by a certified professional.

Q10: How often does the internal 12-volt battery require replacement?

A10: Standard 12-volt lead-acid or AGM batteries typically require replacement every three to five years, though extreme temperatures can shorten this lifespan. If the gate operator moves slowly or fails to function during power outages, the battery should be load-tested. Replacement batteries must match the exact amperage specifications provided in the original manual.

GTO PRO SW2000XLS / SW2002XLS Series Replacement Parts

Products [16]

Frequently Asked Questions : GTO PRO SW2000XLS / SW2002XLS Series Replacement Parts

Q1: What are the primary power requirements for the GTO PRO SW2000XLS and SW2002XLS series?

Q2: How can the correct replacement control board be identified for these models?

Q3: Can a damaged linear actuator arm on the SW2000XLS or SW2002XLS be repaired?

Q4: What is the main difference between parts for the SW2000XLS and the SW2002XLS?

Q5: What role do limit switches play in the operation of the XLS series?

Q6: Is the GTO PRO XLS series compatible with solar power charging?

Q7: What should be done if the remote transmitters stop responding to the receiver?

Q8: Why is the maintenance of safety photo eye sensors critical for these operators?

Q9: Why might the pivot arm brackets require replacement over time?

Q10: How often does the internal 12-volt battery require replacement?