LiftMaster K16-50195 4L270 V-Belt for CSW200U and CSW200UL Swing Gate Operators
The LiftMaster K16-50195 is a replacement 4L270 V-belt for select CSW200U and CSW200UL swing gate operators. This belt is commonly referenced as Q175 and is often associated with 1 HP CSW200 drive configurations where the operator parts diagram calls for a 4L270 belt. The belt transfers motor power through the operator drive system, helping the swing gate move smoothly through the open and close cycle. In service, this part is commonly replaced when the existing belt is cracked, glazed, stretched, slipping on the pulley, or leaving rubber dust inside the operator cabinet. Belt failure can also point to a stiff gate, worn pulley, or incorrect belt tension.
This part should be selected by matching the original component, the operator model, and the parts diagram. LiftMaster and Elite gate and commercial door operator parts often share similar shapes, numbers, and applications, but small differences in belt length, pulley dimensions, board generation, harness layout, or accessory input requirements can determine whether the part will work correctly. For that reason, the compatibility section below is written broadly where supported but still uses careful fitment language where model generation or configuration can change the correct part.
What This Part Does
This V-belt transfers motor power through the operator drive system. When it is properly tensioned and matched to the correct pulley layout, it helps the gate move smoothly through the open and close cycle. A worn belt may slip under load, create noise, delay gate movement, or keep the operator from moving the gate even when the motor is running.
Compatible With
The LiftMaster K16-50195 4L270 V-Belt for CSW200U and CSW200UL Swing Gate Operators is commonly associated with the following LiftMaster or Elite applications. Compatibility should be confirmed by the exact operator model, original part number, and parts diagram, especially when the equipment has been repaired, updated, or modified in the field.
Common Compatible Models and Applications
- LiftMaster CSW200U swing gate operator
- LiftMaster CSW200UL swing gate operator
- Elite CSW200 swing gate operator, commonly 1 HP configurations when Q175 is specified
- Elite CSW200UL swing gate operator, commonly 1 HP configurations when Q175 is specified
- Select CSW200 high-traffic swing gate systems using the 4L270 drive belt
Important Compatibility Notes
- Use the exact original part number or confirmed related service number whenever possible.
- Do not rely on appearance alone; similar LiftMaster parts may not interchange.
- Check the operator model, production generation, horsepower or voltage where applicable, and parts diagram.
- For gate operators, inspect the gate movement and safety devices before returning the operator to service.
- For electronic boards, verify harness layout, accessory wiring, monitored safety inputs, and diagnostic behavior before installation.
Features & Specifications
| Feature / Specification | Details |
|---|
| Manufacturer | LiftMaster |
| Product Type | Replacement V-Belt |
| Part Number | K16-50195 |
| Application | Drive belt replacement for select LiftMaster / Elite CSW200 swing gate operators |
| Compatible Operator Type | CSW200U and CSW200UL swing gate operator applications using the Q175 / 4L270 belt |
| Also Known As | K16-50195, 16-50195, Q175, 4L270, 4L-270, LiftMaster Q175 |
| Notes | This is the Q175 / 4L270 belt path. Do not confuse it with Q045, Q163, or Q164 belt applications used on other LiftMaster gate operator drive layouts. |
Also Known As / Related Part Numbers
The following numbers and search variations are commonly associated with this item. Some are exact service numbers while others are related catalog formats, older labels, or common search terms. Match the part by the operator parts diagram before treating any related number as a direct replacement.
- K16-50195
- 16-50195
- Q175
- 4L270
- 4L-270
- LiftMaster Q175
- Elite Q175
- CSW200 1 HP motor belt
- CSW200UL 1 HP belt
Technician Note
This is the Q175 / 4L270 belt path. Do not confuse it with Q045, Q163, or Q164 belt applications used on other LiftMaster gate operator drive layouts. Inspect related parts before installation. Belt and pulley failures can be caused by alignment, tension, worn bearings, gearbox load, or a gate/door that is binding. Control-board failures can be caused by moisture, insects, surge damage, shorted wiring, failed accessories, or incorrect safety-device wiring.
Before Ordering, Confirm
- Original part number or old service number on the part being replaced
- Operator model number and production generation
- Parts diagram for the exact operator configuration
- Belt length, pulley size, board generation, or harness layout where applicable
- Voltage, horsepower, learn button, safety-device, or accessory requirements where applicable
- No related mechanical binding, wiring short, surge damage, or accessory failure remains unresolved
Professional Advisory
Gate operators and commercial door operators should be serviced with power disconnected and with the moving gate or door secured as needed. Do not bypass monitored safety devices, photo eyes, edges, loop inputs, or entrapment protection to make a system run. After replacement, test the operator, limits, travel, safety devices, accessories, and manual release according to the equipment requirements. High-voltage, heavy-gate, or unsafe operating conditions should be handled by a qualified gate or garage door technician.
Important Ordering Warnings
- Similar-looking LiftMaster parts may not be interchangeable.
- A different belt length, pulley bore, or board generation can cause installation failure or operator damage.
- Do not install electronic boards into equipment with unresolved wiring shorts, water damage, or surge damage.
- Do not use a replacement part to work around a missing or failed safety device.
- If the existing product title, old part number, and parts diagram disagree, verify the operator before publishing or ordering.
Questions & Answers
What is the LiftMaster K16-50195 used for?
The LiftMaster K16-50195 is used as a replacement drive V-belt for CSW200U and CSW200UL swing gate operator applications using the Q175 / 4L270 belt.
What belt number should I match?
Match the belt to 4L270 and the related part numbers listed for this item. The operator parts diagram should call for K16-50195 or one of its related service numbers.
What symptoms can point to a worn gate operator belt?
Common symptoms include slipping, squealing, cracked rubber, rubber dust in the cabinet, uneven gate movement, or a motor that runs while the gate does not move correctly.
Can I use a different belt length if it looks close?
No. Gate operator belts must match the correct length and belt profile. A belt that is close in size can slip, over-tension the pulleys, or wear out quickly.
What else should be inspected when replacing the belt?
Inspect the motor pulley, drive pulley, gearbox, gate balance, chain or arm hardware, and overall gate movement so the new belt is not damaged by a binding or overloaded gate.
