Mighty Mule Power Supply 19V for MM271 - RP1010 Transformer for the 271 Opener
The Mighty Mule RP1010 power supply is the replacement 19V charging supply used with select modern Mighty Mule residential swing gate operators. This product page is written for the MM271 gate opener application, but the same RP1010 part number is also commonly used across several related Mighty Mule models in the MM271, MM371W, MM372W, MM571W, and MM572W family.
In a battery-operated gate opener, the transformer or plug-in power supply does not normally drive the gate motor directly. Its job is to feed the charging circuit so the control board can maintain the battery. When the power supply fails, the gate may work for a while from the battery and then slow down, stop, show low-battery behavior, or fail after the battery discharges.
Correct voltage matters. Older Mighty Mule and GTO operators may use different transformer ratings, including 14VAC or 18VAC supplies, so the RP1010 should only be used where the opener documentation or original part number calls for this 19V supply.
Compatible With
The RP1010 is model-specific to select newer Mighty Mule systems. Compatibility should be confirmed by the opener model and original power supply label.
- Mighty Mule MM271 single swing gate opener
- Mighty Mule MM371W single swing gate opener
- Mighty Mule MM372W dual swing gate opener
- Mighty Mule MM571W single swing gate opener
- Mighty Mule MM572W dual swing gate opener
- Mighty Mule TS571W applications where the RP1010 power supply is specified
- Select newer Mighty Mule battery-charging gate operator systems that call for the RP1010 19V power supply
- Do not use as a replacement for older 14VAC or 18VAC transformers unless the manual specifically calls for RP1010
Features and Specifications
| Manufacturer | Linear / Mighty Mule |
|---|
| Product Type | Gate opener power supply / battery charger input transformer |
|---|
| Part Number | RP1010 |
|---|
| Application | Replacement 19V power supply for MM271 and select Mighty Mule gate operators |
|---|
| Voltage | 19V power supply output |
|---|
| Compatible Operator Type | Battery-powered residential swing gate operators using RP1010 |
|---|
| Included Components | Power supply only unless otherwise stated |
|---|
| Notes | Not interchangeable with older 14VAC or 18VAC transformer models |
|---|
Also Known As / Related Part Numbers
- RP1010
- LIN-RP1010
- Mighty Mule RP1010
- 19V 2A DC transformer
- 19V power supply
- MM271 transformer
- MM371W transformer
- MM372W transformer
- MM571W transformer
- MM572W transformer
- TS571W transformer
Technician Note
If the battery is old or sulfated, replacing only the power supply may not restore normal gate operation. Test the battery and charging input before replacing multiple parts.
Before Ordering
- Confirm the gate opener model is MM271 or another model listed for RP1010 use
- Compare the original transformer label to the RP1010 rating
- Inspect the battery, battery leads, and charging terminals for corrosion or damage
- Confirm the outdoor outlet or GFCI has power
- Do not substitute a different voltage transformer just because the plug looks similar
Professional Advisory
Low-voltage power supply replacement is usually straightforward, but any damaged wiring, water intrusion, repeated blown fuses, or unsafe gate movement should be inspected by a qualified gate technician.
Important Ordering Warnings
- RP1010 is not a universal Mighty Mule transformer
- Do not confuse RP1010 with RB570, RB502, or older GTO transformer part numbers
- A dead battery can mimic a failed power supply
- Use the correct power source and never bypass safety devices or control-board protection
Product Questions and Answers
Is the RP1010 the correct power supply for a Mighty Mule MM271?
Yes, the RP1010 is commonly listed for the MM271 application when the operator uses the newer 19V power supply. Always compare the original power supply label and operator manual before ordering.
What other Mighty Mule models commonly use the RP1010?
The RP1010 is commonly associated with MM271, MM371W, MM372W, MM571W, MM572W, and TS571W applications where a 19V power supply is specified.
Will this fix a gate opener that opens slowly or stops after a few cycles?
It may help if the battery is not being charged, but a weak battery, bad wiring, bad control board, or poor power connection can cause the same symptoms.
Can I use this in place of an older 18VAC or 14VAC transformer?
No. Use the transformer rating specified for the operator. Similar-looking plug-in transformers are not always interchangeable.
Does the RP1010 power the gate motor directly?
On these battery-based systems, the power supply maintains the battery charging circuit. The battery supplies the high current needed for gate movement.