Mighty Mule MM571W Replacement Control Board - RP1007 Logic Board
The Mighty Mule RP1007 is a replacement logic board for select Mighty Mule smart swing gate operators. On the MM571W, this board is the main control center for the opener. It processes push-button commands, remote receiver signals, smart-control communication, limit and obstruction information, battery/charging conditions, accessory inputs, and monitored safety-device behavior.
This board is commonly replaced when the opener has a confirmed control-board failure, visible board damage, intermittent operation, no response from known-good controls, or failure after a surge, water intrusion, insect contamination, or wiring short. It is important to diagnose the whole operator before replacing the board. A weak battery, failed power supply, damaged arm cable, shorted accessory, poor terminal connection, or safety-device fault can create symptoms that look like a bad board.
Although the RP1007 board is used across more than one Mighty Mule smart operator, it is not a universal Mighty Mule board. It is tied to the MM371W, MM372W, MM571W, and MM572W family. Older FM-series operators and several earlier GTO/Mighty Mule boards use different electronics, terminals, programming, and control logic. Match the model number, board label, and control box layout before ordering.
Compatible With
RP1007 is commonly associated with these Mighty Mule smart swing gate operator models when the original board and control box match:
- Mighty Mule MM371W smart single swing gate opener
- Mighty Mule MM372W smart dual swing gate opener
- Mighty Mule MM571W heavy-duty smart single swing gate opener
- Mighty Mule MM572W heavy-duty smart dual swing gate opener
Depending on the installation, this board may be used with compatible Mighty Mule accessories connected to the operator, including select remotes, keypads, push buttons, solar charging equipment, power supplies, safety devices, and smart-control accessories supported by the opener model. Accessory compatibility should be confirmed from the operator manual.
Also Known As / Related Part Numbers
- RP1007
- LIN-RP1007
- Mighty Mule RP1007 logic board
- Logic Board for MM371/MM372/MM571/MM572 operators
- MM371W control board reference
- MM372W control board reference
- MM571W control board reference
- MM572W control board reference
- Related loaded control box reference: RP1004
- Related antenna reference: RP1008
- Related power supply reference: RP1010
Related numbers are included for search and service reference. They are not all direct replacements for the RP1007 board.
Features & Specifications
| Manufacturer | Mighty Mule / Linear / Nice North America |
|---|
| Product Type | Replacement logic board / control board |
|---|
| Part Number | RP1007 |
|---|
| Application | MM571W single smart swing gate opener service part |
|---|
| Compatible Operator Type | Residential smart swing gate operator |
|---|
| Voltage | 12V DC operator system |
|---|
| Safety Monitoring | Used in UL 325 compliant smart operator family when installed and configured correctly |
|---|
| Notes | Match original board label, operator model, control box layout, and wiring before ordering |
|---|
Technician Note
If the original board failed because of a shorted accessory, wet control box, damaged arm cable, incorrect charger, lightning surge, or reversed wiring, the new board may fail immediately after installation. Inspect and correct the cause of failure before installing the replacement board.
Before Ordering Checklist
- Confirm the operator model is MM571W or another supported RP1007 model
- Confirm the original control board label or parts diagram calls for RP1007
- Compare terminal layout and wire connections before removal
- Check the battery and charging system before condemning the board
- Inspect arm cable, accessory wiring, and safety-device wiring for shorts
- Do not order this board for older FM-series or non-W operators unless a parts diagram confirms it
Professional Advisory
Control board replacement may require reprogramming and safety-device verification. If the gate moves unexpectedly, has missing safety devices, or has wiring damage, stop using the operator and have the system checked by a qualified gate technician.
Product Q&A
Is the RP1007 board compatible with the Mighty Mule MM571W?
Yes, RP1007 is commonly listed as the replacement logic board family for Mighty Mule MM371W, MM372W, MM571W, and MM572W smart swing gate operators, including the MM571W when the original board and control box configuration match.
Does RP1007 fit older Mighty Mule FM or non-W smart operators?
No. RP1007 is for the newer smart MM371/MM372/MM571/MM572 operator family. It should not be assumed to fit older FM350, FM500, FM502, MM560, MM562, or non-W operator generations.
Will the opener need setup after the board is replaced?
Yes. After board replacement, the operator may need limit, remote, accessory, obstruction, and smart-control setup according to the operator manual.
What should be checked before replacing the logic board?
Check the battery, power supply, arm wiring, accessory wiring, antenna, safety devices, fuses, and signs of water or insect damage. A bad external device can make a good control board appear defective.
Can safety devices be bypassed to make the gate run?
No. Monitored safety and entrapment protection devices should not be bypassed. If the operator will not run because of a safety fault, the fault should be diagnosed and corrected properly.
