SECO-LARM SK-1323-SDQ Sealed Housing Weatherproof Stand-Alone Digital Keypad
The SK-1323-SDQ is a sealed weatherproof stand-alone keypad built for outdoor access points that need PIN-code entry without a separate controller. It is a good fit for pedestrian gates, small commercial doors, shared equipment areas, service entrances, and properties where a compact weather-resistant keypad is preferred over a larger surface-mount vandal-resistant unit. The keypad has two relay outputs, supports a large number of user codes, and includes egress and door-sensor inputs for typical access-control wiring. Because this is the SDQ model, it should be selected for code-only access. If the job requires cards or fobs, the SPQ proximity version should be checked instead.
Compatible With
- Outdoor pedestrian gate and door access points needing code-only entry
- Gate operator low-voltage open/access inputs that accept a dry-contact command
- Electric strikes, magnetic locks, egress buttons, and door-sensor circuits within published ratings
- Small commercial, residential community, service entry, and equipment-room access applications
- Replacement for compatible SK-1323-SDQ installations where the housing, wiring, voltage, and programming needs match
Also Known As / Related Part Numbers
- SK-1323-SDQ
- SK1323SDQ
- SECO-LARM SK-1323-SDQ
- Enforcer sealed-housing digital keypad
- SK-1323-SxQ keypad family
- Related model: SK-1323-SPQ proximity-reader version
- Related model: SK-1323-BDQ black housing version
Features & Specifications
| Manufacturer | SECO-LARM / ENFORCER |
|---|
| Product Type | Sealed-housing weatherproof stand-alone digital keypad |
|---|
| Part Number | SK-1323-SDQ |
|---|
| Application | Outdoor keypad access for doors, pedestrian gates, and controlled entry points |
|---|
| Operating Voltage | 12 to 24 VAC/VDC |
|---|
| User Capacity | Up to 1,010 user codes |
|---|
| Relay Outputs | Two Form C relays, commonly 1A at 30VDC |
|---|
| Inputs | Two egress inputs and door sensor input |
|---|
| Tamper Sensor | Optical tamper sensor |
|---|
| Environmental Rating | Weatherproof / IP65 keypad family |
|---|
| Credential Technology | Keypad code only; no proximity reader on SDQ version |
|---|
Technician Note
The sealed housing helps with outdoor durability, but the keypad still needs proper conduit, drip protection, and strain relief so water does not follow the cable into the wall or post.
Before Ordering Checklist
- Confirm the job needs keypad codes only, not card access.
- Verify the mounting surface and cable path.
- Check whether one or two relay outputs are required.
- Confirm the voltage and power source.
- Document user-code ranges and master code after setup.
Professional Advisory
When used on a gate, wire the relay only to the correct low-voltage access input and leave all monitored safety devices connected and functional.
Important Ordering Warnings
- Do not order the SDQ version if the customer needs proximity cards or key tags.
- Do not exceed relay ratings or use the relay as a high-voltage switch.
- Confirm door/gate hardware before using output 2 for a secondary function.
Product Questions and Answers
What is the difference between SK-1323-SDQ and SK-1323-SPQ?
The SK-1323-SDQ is the digital keypad-only version. The SK-1323-SPQ adds a built-in 125 kHz proximity reader for cards or tags.
Can this keypad be installed outside?
Yes, it is part of SECO-LARM's sealed weatherproof keypad family, but the installation still needs proper conduit, mounting, and weather protection.
How many relays does it have?
It has two Form C relay outputs that can be programmed for access and auxiliary functions when wired within rating.
Can it be used for a gate opener?
Yes, if the gate opener has a compatible low-voltage access-command input. It should not be connected to motor power or safety circuits.
Does it need a separate access-control panel?
No, it can operate as a stand-alone keypad, although some installations may still use a separate controller depending on site design.
