The Security Brands SecurePass TR1 is a mid-range UHF vehicle tag reader for gate, parking, and perimeter access-control applications. It is designed to read compatible UHF vehicle tags from an approaching vehicle and send a 26-bit Wiegand signal to a compatible access-control system.
This reader is commonly associated with Security Brands part references 40-TR1 and 40-200. Current Security Brands product material shows the model as 40-TR1, while some distributor and store listings use 40-200 for the SecurePass TR1 vehicle tag reader. Because of that part-number difference, the physical label, supplier record, and purchase order should be checked before publishing or ordering replacements.
The SecurePass TR1 is useful for properties that want vehicle access without requiring the driver to stop at a keypad, roll down a window, or present a handheld card at a short-range reader. When the vehicle tag, reader position, controller input, and programming are set up correctly, the system can grant access as the tagged vehicle approaches the gate or controlled entry point.
This is a Wiegand vehicle tag reader, not a stand-alone gate opener, not a complete access-control system, and not a vehicle detector. It must be connected to a compatible 26-bit Wiegand controller, select Security Brands Ascent system, Security Brands Edge system, or other compatible access controller. The controller decides whether the presented tag is valid and then sends the access command to the gate operator or door controller.
The TR1 reader uses UHF vehicle tags and is intended for mid-range vehicle identification. Current Security Brands information lists a read range of up to 20 feet. Real-world read distance can vary based on tag type, tag placement, vehicle angle, mounting height, reader aim, nearby metal, lane width, electrical noise, and controller setup.
The included mounting hardware gives the installer flexibility in the field. The reader can be mounted to a post or round pipe using the post-mount bracket with U-bolt, or it can be mounted to a flat surface using the surface-mount bracket. The bracket allows angle adjustment so the reader can be aimed into the correct vehicle approach zone instead of reading too early, too late, or across the wrong lane.
The SecurePass TR1 should not be confused with SecurePass CR proximity card readers, Edge E2/E3 card readers, Ascent K2 keypad readers, AWID long-range AVI readers, loop detectors, vehicle presence sensors, or gate safety devices. The TR1 is for reading compatible UHF vehicle tags. It does not confirm that the gate path is clear and must not be used as a safety device.
The Security Brands SecurePass TR1 can be used with compatible access controllers that accept 26-bit Wiegand input. Final compatibility depends on the controller model, Wiegand format, credential programming, vehicle tag type, wiring distance, power source, gate operator input, and lane layout.
Important: The SecurePass TR1 does not replace the access controller or the gate operator. It reads a compatible vehicle tag and sends Wiegand data to the controller. The controller, relay output, gate operator, safety devices, emergency access equipment, and access rules must be installed and programmed correctly for the site.
| Feature / Specification | Details |
|---|---|
| Manufacturer | Security Brands / American Access Systems |
| Product Family | SecurePass TR |
| Product Type | Mid-range UHF vehicle tag reader |
| Current Manufacturer Model Reference | 40-TR1 |
| Common Distributor / Store Reference | 40-200 |
| Common Name | SecurePass TR1 |
| Reader Technology | UHF vehicle tag reading |
| Output Protocol | 26-bit Wiegand |
| Read Range | Up to 20 ft under suitable conditions |
| Credential Type | Compatible UHF vehicle tags |
| Compatible Tag References | Security Brands 40-TW windshield tag and 40-TL license plate tag where available and properly programmed |
| Feedback | LED and audible-tone feedback |
| Construction | Weather-resistant polycarbonate construction |
| Mounting Hardware | Post-mount bracket with U-bolt and surface-mount bracket included |
| Mounting Adjustment | Mounting holes allow reader positioning in 10-degree increments from 0 to 60 degrees |
| Power | Power supply included; installation guide shows +12V and ground reference for Wiegand controller wiring |
| Wire Harness Reference | Yellow Data 0, gray Data 1, red Trigger +, black Trigger - / Ground depending on installation type |
| Controller Compatibility | Select Ascent models, Edge systems, and other 26-bit Wiegand controllers |
| Simple Relay Note | When used in a simple relay setup, the onboard relay triggers whenever a valid tag is read |
| Included Items | Reader, power supply, post-mount bracket with U-bolt, and surface-mount bracket |
| Warranty Reference | Two-year limited warranty commonly listed by the manufacturer |
| Important Service Note | Read performance depends on tag type, tag position, reader aiming, vehicle approach, lane layout, and controller programming. |
Related item note: Vehicle tags, access controller, gate operator, post or mounting pipe, conduit, access-control cable, low-voltage wiring, safety devices, loop detectors, fire access equipment, and installation labor are separate unless the product listing specifically states that they are included.
The SecurePass TR1 is a reader for authorized UHF vehicle tags. It should not be treated like a loop detector or vehicle presence sensor. A loop detector senses a vehicle in a detection zone. A tag reader identifies a tag. Those are different jobs, and most gate systems still need proper safety loops, photo eyes, safety edges, and monitored entrapment protection where required.
Reader placement is the most important field issue. Aim the reader at the intended vehicle approach path and avoid aiming across another lane, exit lane, sidewalk, or nearby driveway. If the reader is aimed too wide or too far into the wrong area, it may read a valid tag before the vehicle is in the desired access position.
Tag placement also matters. Windshield tags and license plate tags can read differently depending on glass type, windshield tint, metalized film, vehicle shape, mounting height, tag orientation, and approach angle. Test the tag style on the actual vehicle type before finalizing the mounting position.
Use the current model-specific information when selling this product. Security Brands currently shows the SecurePass TR as model 40-TR1, while many distributor records and store listings still use 40-200. Both references are commonly associated with this TR1 reader, but the part number should be verified before ordering replacement stock.
When wiring the reader, follow the access controller or gate operator documentation. Do not wire low-voltage reader outputs into high-voltage operator power. If a simple relay trigger layout is used, understand that a valid tag read can trigger the onboard relay, so the reader position, tag programming, and safety layout must be tested carefully.
The Security Brands SecurePass TR1 should be installed by a qualified gate, access-control, or low-voltage technician when Wiegand wiring, controller programming, tag encoding, relay wiring, reader aiming, or gate operator input wiring is not clearly understood.
Do not use this reader to bypass gate safety devices, monitored photo eyes, safety edges, loop detectors, stop circuits, emergency access devices, or required entrapment protection. The SecurePass TR1 provides vehicle tag identification only. The gate operator must still be installed, wired, and tested as a safe automatic gate system.
After installation, test with the actual vehicle tags that will be used on the property. Confirm read distance, tag position, lane coverage, controller response, relay command, gate response, event logging where applicable, emergency access, and all gate safety-device operation before turning the system over to the customer.
The SecurePass TR1 is a mid-range UHF vehicle tag reader that sends 26-bit Wiegand data to a compatible access controller when an authorized vehicle tag is read.
Current Security Brands material shows the SecurePass TR as model 40-TR1, while some distributor and store listings use 40-200. Verify the supplier record and product label before ordering replacement stock.
The SecurePass TR1 is intended for select Security Brands Ascent models, Security Brands Edge systems, and other compatible 26-bit Wiegand controllers where the wiring, credential format, and programming are matched correctly.
The SecurePass TR1 is designed for compatible UHF vehicle tags, such as windshield or license plate style tags where supported. Standard short-range proximity cards and fobs should not be assumed to work as vehicle tags.
Security Brands lists the SecurePass TR1 with a read range of up to 20 feet. Actual distance depends on tag type, tag placement, reader aiming, vehicle angle, mounting height, and site conditions.
No. The SecurePass TR1 is a vehicle tag reader, not a vehicle presence detector or gate safety device. Loop detectors, photo eyes, safety edges, and required entrapment protection must be handled separately.
The current installation guide shows the reader, power supply, post-mount bracket with U-bolt, and surface-mount bracket. Confirm included parts with the current box contents before installation.
Check the controller's 26-bit Wiegand support, tag compatibility, mounting height, reader angle, lane coverage, wiring path, power source, relay layout, emergency access, and the gate safety system before completing the installation.