The HySecurity MX002723 is a lower arm linkage assembly for select HySecurity / Nice HySecurity StrongArm M30 and StrongArm M50 crash barrier applications. This linkage is part of the StrongArm M30/M50 arm and hardware assembly and helps support correct mechanical movement of the lower arm system.
This is a model-specific StrongArm crash barrier component. It should be matched by operator model, serial number, lower arm assembly, linkage position, bearing condition, retaining hardware, and current HySecurity parts diagram before ordering. Do not substitute a similar-looking linkage unless the parts diagram confirms the same part number.
The lower arm linkage assembly connects into the StrongArm M30/M50 arm hardware system and helps maintain proper arm movement, geometry, and mechanical alignment. In a properly maintained barrier, the linkage works with the lower arm assembly, upper arm, straps, bearings, saddle assembly, catch pin, and related hardware.
If the linkage assembly is worn, bent, loose, or damaged, the barrier arm may move unevenly, bind, sit out of alignment, place added stress on bearings, or wear related hardware faster than normal. Linkage damage can also be a sign of impact damage, incorrect arm setup, worn bearings, loose retaining hardware, or a distorted arm assembly.
This linkage assembly may be used with the following applications where the current HySecurity parts diagram confirms MX002723:
Important: Do not assume this linkage fits StrongArmPark, StrongArm 36, StrongArm DOT, or unrelated barrier arm systems. The confirmed application is StrongArm M30/M50 where the current parts diagram lists MX002723.
StrongArm arm and linkage parts can look similar but may not be interchangeable. Linkage geometry, pivot spacing, bearing size, arm type, hardware stack-up, and model family all matter.
| Part / Component | Common Description | Interchangeability Note |
|---|---|---|
| MX002723 | Lower arm linkage assembly | Correct where MX002723 is listed for the StrongArm M30/M50 lower arm linkage location |
| MX2604-NN | Lower arm assembly with strap and saddle | Related lower arm assembly, not the same as the lower arm linkage assembly |
| MX002588 | Poly bearing, 1.25 inch ID x 1.5 inch | Related bearing used in the arm hardware diagram, not the linkage assembly |
| MX3142 | Saddle assembly with hardware | Related arm hardware component, not the lower arm linkage assembly |
| Upper arm assemblies | Upper arm assemblies for M30, M50, or manual configurations | Different arm assemblies; not interchangeable with the lower arm linkage |
The MX002723 lower arm linkage assembly is tied to the StrongArm M30/M50 arm geometry. It should not be selected based only on the words lower arm or by visual similarity. The lower arm linkage, bearings, lower arm assembly, upper arm assembly, straps, saddle hardware, and catch pin all work together as a matched mechanical system.
If the original linkage failed due to vehicle impact, arm binding, worn bearings, loose retaining hardware, or frame movement, inspect the surrounding arm hardware before installing a new linkage assembly. Replacing only the linkage may not correct the problem if the lower arm, upper arm, saddle, straps, catch hardware, or pivot points are also damaged.
| Feature / Specification | Details |
|---|---|
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX002723 |
| Product Type | Lower arm linkage assembly |
| Common Description | Arm, Lower Linkage Assy / Linkage Assembly, Lower Arm |
| Common Operator Family | Select HySecurity StrongArm M30 and StrongArm M50 applications where specified |
| Assembly Area | StrongArm M30/M50 arm and hardware assembly |
| Function | Supports proper lower arm linkage movement and mechanical alignment |
| Related Hardware | Lower arm assembly, upper arm assembly, straps, bearings, saddle assembly, catch pin, and retaining hardware should be inspected during service |
| Package Contents | Lower arm linkage assembly; confirm included pins, bearings, bushings, fasteners, and current package contents before ordering |
Before replacing the MX002723 lower arm linkage assembly, inspect the entire StrongArm M30/M50 arm system. A damaged linkage can be caused by vehicle impact, worn bearings, loose straps, bent lower arm sections, a damaged upper arm, worn catch hardware, saddle misalignment, or a barrier arm that is not seating correctly.
Check for ovaled holes, cracked welds, worn bushings, seized bearings, loose fasteners, bent linkage plates, and uneven arm movement. If the barrier was hit, do not assume the linkage is the only damaged part. The lower arm assembly, upper arm assembly, saddle, catch pin, and frame mounting points should all be inspected before the operator is returned to service.
The MX002723 is part of the arm linkage system on a StrongArm crash barrier. Service should be performed by a qualified gate technician when the repair involves heavy barrier arm movement, linkage removal, impact damage, worn pivots, bearing replacement, catch hardware alignment, or unknown prior modifications.
Do not bypass arm hardware, catch hardware, controller protections, vehicle detection, safety devices, limits, disconnects, or operator safeguards to keep the barrier running. If the arm is bent, binding, loose, misaligned, or damaged from impact, the complete barrier arm assembly should be inspected before continued operation.
The HySecurity MX002723 is a lower arm linkage assembly used on select StrongArm M30 and StrongArm M50 crash barrier arm applications where the parts diagram confirms this part number.
Yes, HySecurity parts documentation lists the lower arm linkage assembly for StrongArm M30/M50 arm hardware applications, but the exact fit should still be verified by model, serial number, and current parts diagram.
No. MX002723 is the lower arm linkage assembly. The lower arm assembly with strap and saddle is a related part but is not the same component.
Check the lower arm, upper arm, bearings, pins, straps, saddle assembly, catch pin, mounting holes, and signs of impact damage before replacing the linkage assembly.
Yes. A bent, worn, or loose lower arm linkage can cause uneven arm movement, binding, poor alignment, added bearing wear, and stress on related StrongArm M30/M50 hardware.
The part is identified as a lower arm linkage assembly. Package contents should be confirmed before ordering, especially if bearings, pins, bushings, fasteners, or retaining hardware are also needed.
Yes. Because this part is used in a heavy crash barrier arm assembly, installation should be handled by a qualified gate technician when heavy arm movement, impact damage, linkage alignment, or safety concerns are involved.