The Miller Edge MEP190 10 ft pneumatic treadle is a black, all-weather PVC pressure-sensitive activation treadle used for select vehicle detection and signaling applications. It is commonly used where a vehicle driving over the treadle needs to activate a connected door, gate, alarm, or signaling control through an external pneumatic switch.
The MEP190 is the pneumatic version of the Miller Edge ME190 treadle family. It uses attached pneumatic tubing to send air pressure to an external pneumatic switch. The switch then converts that pressure into an electrical contact signal for the connected control equipment. Always confirm the required switch, tubing path, control input, and mounting method before ordering.
The MEP190 treadle responds when a vehicle rolls over the PVC treadle body. That pressure creates an air pulse through the attached pneumatic tube. When connected to the correct pneumatic switch, such as a compatible Miller Edge PS-20A switch, the system can provide a contact output to a gate operator, garage door operator, signaling device, alarm panel, or access control circuit.
This Miller Edge MEP190 treadle may be used with select control systems where a pneumatic pressure switch contact is an approved activation input. Compatibility depends on the switch used, the control circuit, the installation surface, the vehicle traffic pattern, and the intended function.
Do not order this item based only on the word "treadle." The Miller Edge ME190 treadle family includes different configurations. The MEP190 is the pneumatic treadle version, while the MAW190 is the Air-Wave treadle version. Pneumatic and Air-Wave systems use different switch styles and should not be treated as the same system.
The treadle itself does not replace the external pneumatic switch unless the product listing specifically includes one. Miller Edge product information indicates switches are sold separately for ME190 treadle systems. Confirm whether the PS-20A pneumatic switch, treadle retainer, mounting hardware, tubing fittings, and operator-side wiring are included or must be ordered separately.
| Specification | Details |
|---|---|
| Brand | Miller Edge |
| Model / Part Number | MEP190 |
| Product Family | ME190 treadle family |
| Product Type | Pneumatic pressure-sensitive treadle |
| Listed Length | 10 ft |
| Color | Black |
| Material | PVC |
| Configuration | Non-monitored pneumatic treadle |
| Detection Type | Pressure-sensitive vehicle activation |
| Common Applications | Parking garages, service stations, car washes, drive-through signaling, motorized doors, and automated gates |
| Approximate Dimensions | Approximately 3-11/16 in to 3-3/4 in wide x 3/4 in high |
| Sensitivity | Approximately 2 lb / 32 oz activation sensitivity |
| Lead Hose | Attached 5/16 in ID PVC pneumatic tubing |
| Outlet Location | End outlet |
| Operating Temperature | Approximately -30 degrees F to +158 degrees F |
| Electrical Components in Treadle | None inside the treadle body; requires external pneumatic switch for electrical contact output |
| Related Pneumatic Switch | Miller Edge PS-20A or compatible pneumatic switch, verify before ordering |
| Optional Accessory | Treadle retainer, verify if required and sold separately |
| Warranty | 1 year, subject to manufacturer terms |
| Country of Origin | Made in USA |
The product title may use the words "treadle switch," but the MEP190 treadle normally works with an external pneumatic switch. Confirm current package contents before publishing, picking, or shipping.
Before replacing or installing a pneumatic treadle, review the entire activation system. A treadle will not correct a failed pneumatic switch, damaged tubing, wrong control input, poor mounting surface, water-filled tubing, or operator control fault.
The MEP190 is an activation treadle, not a monitored safety edge. It is often used where a vehicle needs to trigger a door, gate, signal, or alert by physically driving over the treadle. The external pneumatic switch is what provides the electrical contact back to the control system.
On outdoor installations, routing the pneumatic tube cleanly matters. Avoid low spots that can hold water, tight bends that restrict air movement, and exposed hose runs that can be crushed by traffic or maintenance equipment.
This treadle should be installed by a qualified door, gate, access control, low-voltage, or facility maintenance technician familiar with the equipment being controlled. The treadle, pneumatic tube, switch, and control input should be installed according to the manufacturer instructions and the connected operator or control panel documentation.
Do not bypass photo eyes, sensing edges, monitored safety inputs, loop detectors, warning devices, fire access controls, door reversal systems, or entrapment protection to make a gate or door run. If the treadle does not activate the system, diagnose the pneumatic tube, switch, contact output, wiring, and control input instead of defeating safety circuits.
A pneumatic treadle is part of an activation or signaling system, not a substitute for required safety devices. If the door, gate, or equipment moves unexpectedly, fails to stop, fails to reverse, or ignores safety inputs, stop using it until the operator, controls, and safety devices are checked by a qualified technician.
For South Florida customers, local pickup in the Hialeah Gardens area may be available when inventory allows. Confirm availability, package contents, switch requirements, and retainer needs before coming in for pickup.
The Miller Edge MEP190 10 ft treadle is used for pressure-sensitive vehicle activation and signaling in select gate, door, parking garage, service station, car wash, and drive-through applications.
Yes. MEP190 is the pneumatic version of the Miller Edge ME190 treadle family. It uses attached pneumatic tubing and requires a compatible external pneumatic switch to provide an electrical contact signal.
No. MEP190 is the pneumatic treadle version. MAW190 is the Air-Wave treadle version and uses Air-Wave style switching equipment. They should not be ordered interchangeably.
Not automatically. Miller Edge treadle information indicates that switches are sold separately unless the listing specifically includes one. Confirm whether the PS-20A pneumatic switch is included before ordering.
The Miller Edge PS-20A pneumatic switch is commonly associated with pneumatic configured sensing edges and treadles. Confirm the switch output and enclosure needs before connecting it to the control system.
Yes. The MEP190 treadle is intended for indoor or outdoor applications when properly installed. The tubing route, switch enclosure, drainage, and retainer method should be planned for the site conditions.
No. The pneumatic MEP190 treadle is a non-monitored pressure activation device. It should not be used as a substitute for required monitored photo eyes, monitored sensing edges, or UL 325 entrapment protection.
Confirm the 10 ft length, pneumatic configuration, switch requirement, tubing route, outlet location, retainer needs, mounting surface, control input compatibility, and whether the PS-20A switch or any accessories are included.