AES ENCIP65-LG, 200 x 150 x 55mm iGate Enclosure ONLY. IP65

AES ENCIP65-LG, 200 x 150 x 55mm iGate Enclosure ONLY. IP65

The AES ENCIP65-LG is a large IP65 plastic enclosure used for compatible AES iGate installations. It measures 200 x 150 x 55 mm and provides a protective housing for low-voltage iGate access control equipment where the device needs to be mounted in a more protected enclosure.

This is the enclosure only. It should not be confused with a complete iGate cellular gate opener, iGate Wi-Fi controller, relay device, power supply, antenna kit, SIM card, or finished access control package. The enclosure provides the housing, but the electronics and installation accessories must be confirmed separately.

What This Enclosure Does

The ENCIP65-LG provides a protective plastic housing for compatible AES iGate equipment. It is useful when an iGate device needs a more secure and weather-resistant mounting location, especially at gate columns, equipment posts, low-voltage access control areas, or service locations where the device should not be left exposed.

• Large IP65 plastic enclosure for compatible AES iGate applications
• Measures 200 x 150 x 55 mm
• Used to house and protect compatible low-voltage iGate equipment
• Helps protect against dust, debris, and weather exposure when installed correctly
• Four mounting screw holes for installation support
• Enclosure-only item; electronics are not included
• Useful for service replacement, new installation, or enclosure upgrade work

Compatible With

The AES ENCIP65-LG may be used with compatible AES iGate models where the larger 200 x 150 x 55 mm enclosure size is required or preferred. Always confirm the iGate model, internal clearance, wiring layout, antenna path, and cable entry method before ordering.

• Select AES iGate cellular gate opener applications
• Select AES iGate Wi-Fi or iGate-style access control installations where the large enclosure is specified
• Installations where the 200 x 150 x 55 mm enclosure size is required
• Replacement applications where the existing housing is marked or cross-referenced as ENCIP65-LG
• Low-voltage gate access installations needing a protective iGate enclosure
• Installations where the smaller ENCIP65-SM enclosure is not large enough

Important Compatibility Warning

Do not order this enclosure by size or appearance alone. AES offers different iGate products, enclosure sizes, and accessory kits. This part is the large IP65 enclosure only and does not include the electronics or wiring accessories needed to make an iGate system operate.

• Confirm the required part number is ENCIP65-LG.
• Confirm the required enclosure size is 200 x 150 x 55 mm.
• Confirm the installed AES device is compatible with the large iGate enclosure.
• Confirm this is not being ordered instead of the complete iGate device.
• Confirm whether the smaller ENCIP65-SM enclosure is actually required instead.
• Confirm whether cable glands, grommets, screws, backplate, antenna parts, or mounting hardware are included with your actual package.
• Confirm the enclosure can be sealed properly after drilling or routing cable entries.

ENCIP65-LG Compared With Similar AES Enclosure Parts

Similar Parts That Are Not Automatically Interchangeable

• AES ENCIP65-SM: Related small IP65 iGate enclosure. It is not the same size as ENCIP65-LG and may not provide the same internal space.
• AES IGATE-WIFI-ENC: Related iGate Wi-Fi product with enclosure. It should not be treated as the same as an empty enclosure-only housing.
• AES iGate cellular or Wi-Fi devices: These are the actual access control devices. They are not included with this enclosure-only listing.
• Generic IP65 plastic enclosures: May have different dimensions, mounting hole positions, lid design, gasket quality, cable entry options, or internal clearance.
• Metal enclosures: Metal housings may affect wireless or cellular signal and should not be substituted without confirming the installation requirements.

Not Intended For

• Replacing the iGate controller or cellular gate opener electronics
• Replacing a relay board, PCB, SIM card, cellular module, antenna, or power supply
• Replacing an OPYN, Praetorian, Prime, or other AES intercom enclosure unless compatibility is confirmed
• Housing high-voltage gate motor wiring
• Charging batteries or powering access control equipment by itself
• Creating a weather-rated installation after unsealed holes, oversized openings, or improper cable entries
• Bypassing gate operator safety devices, emergency access, fire access, or monitored entrapment protection

Features & Specifications

Also Known As / Related Part Numbers

• AES ENCIP65-LG
• ENCIP65-LG
• ENCIP65LG
• AES iGate IP65 Enclosure Large
• AES Large iGate Enclosure
• AES 200 x 150 x 55 mm iGate Enclosure
• AES 8 x 6 iGate Enclosure
• AES IP65 Plastic Enclosure for iGate
• AES iGate Enclosure Only
• ENCIP65-SM - related small iGate enclosure, not the same large enclosure
• IGATE-WIFI-ENC - related complete iGate Wi-Fi product with enclosure, not the same enclosure-only item

Related Parts and Accessories

• AES ENCIP65-SM small IP65 plastic enclosure for iGate where the smaller size is required
• AES iGate cellular and iGate Wi-Fi access control devices where enclosure compatibility is confirmed
• AES IGATE-WIFI-ENC complete iGate Wi-Fi package where a full device with enclosure is required
• Compatible antennas, power supplies, relay wiring, and network/cellular accessories only where required by the installed iGate system
• Approved cable glands, grommets, sealant, mounting screws, and weather-protection hardware where required by the installation

Technician Note

The enclosure rating depends heavily on the installation. Drilling extra holes, using the wrong cable entry, leaving unused openings, crushing the gasket, or mounting the box where water can sit against the cable entry can reduce the protection the enclosure provides. Use proper cable glands, drip loops, and sealing practices for the site.

Also consider wireless signal before mounting. Cellular, Wi-Fi, and RF devices can perform poorly if the enclosure is placed behind metal, inside a shielded cabinet, too low to the ground, or in an area with weak signal. Confirm the antenna route and signal conditions before final mounting.

Before Ordering, Confirm

• Confirm the exact part number is ENCIP65-LG.
• Confirm the required enclosure size is 200 x 150 x 55 mm.
• Confirm the installed AES device is part of the iGate product family.
• Confirm the internal space is large enough for the device, wiring, and cable bend radius.
• Confirm whether the smaller ENCIP65-SM enclosure is the correct part instead.
• Confirm whether the job requires an enclosure only or a complete iGate device with enclosure.
• Confirm the antenna, power, relay, and cable entry locations before drilling.
• Confirm whether cable glands, grommets, mounting screws, backplate, or sealing parts must be ordered separately.
• Confirm the enclosure location is suitable for weather exposure, service access, and signal performance.

Installation and Service Notes

• Mount the enclosure on a solid surface using suitable fasteners for the wall, post, or gate column.
• Use proper cable glands or grommets for cable entry points.
• Seal unused openings so the enclosure can maintain its weather protection.
• Do not leave the lid gasket pinched, twisted, dirty, or missing.
• Use a drip loop where cables enter from above or from exposed areas.
• Avoid mounting the enclosure where it will sit in standing water or direct spray from irrigation.
• Keep low-voltage access control wiring separated from high-voltage gate operator wiring.
• After installation, test the iGate device, relay trigger, network or cellular connection, and any connected access control functions.

Professional Advisory

Low-voltage gate access equipment, enclosure mounting, cable entry sealing, antenna routing, and iGate service should be handled by a qualified gate access or low-voltage technician when the wiring is unclear or the system controls an automated gate. Do not use an enclosure replacement, wiring changes, or accessory mounting to bypass required gate safety devices, emergency access equipment, fire access equipment, monitored photo eyes, safety edges, or operator safety circuits.

Product Questions & Answers

What is the AES ENCIP65-LG?

The AES ENCIP65-LG is a large IP65 plastic enclosure for compatible AES iGate installations. It measures 200 x 150 x 55 mm and is sold as the enclosure only.

Does the ENCIP65-LG include the iGate device?

No. This listing is for the enclosure only. It does not include the iGate controller, cellular module, Wi-Fi device, relay board, SIM card, antenna, power supply, or wiring accessories unless your package specifically states otherwise.

What size is the ENCIP65-LG enclosure?

The ENCIP65-LG measures 200 x 150 x 55 mm, which is approximately 7.9 in. x 5.9 in. x 2.2 in.

Is this the same as ENCIP65-SM?

No. ENCIP65-LG is the larger 200 x 150 x 55 mm enclosure. ENCIP65-SM is the smaller related iGate enclosure and should not be substituted unless the smaller size is correct for the installation.

Is the ENCIP65-LG weatherproof?

It is listed as an IP65 enclosure, but the final weather protection depends on proper installation. Drilled holes, cable entries, gaskets, glands, and mounting location all affect how well the enclosure protects the equipment.

Can this enclosure be used for any AES product?

No. It should be used only where the installed AES device and parts listing call for this iGate enclosure or where the installer has confirmed size, mounting, wiring, and environmental requirements.

What should be checked before installing this enclosure?

Before installation, check enclosure size, device fit, cable entry locations, antenna routing, gasket condition, mounting surface, weather exposure, and whether the required cable glands or mounting hardware are included.