The Genie 107042.0004.S is an interior flush mount commercial key switch station used with select Genie commercial door operator control circuits. It provides keyed Open and Close commands using a center-return key switch, plus a separate Stop button on the faceplate.
This station is commonly used where the customer needs restricted local operation from an indoor flush mount wall location. The tamper-proof design requires the key to remove the cover, helping reduce unauthorized access to the station wiring and mounting screws. Always confirm the operator wiring diagram and control circuit before ordering or installing this part.
The 107042.0004.S allows an authorized user to operate a compatible commercial door operator with a key. Turning the key one direction sends an Open command, turning it the other direction sends a Close command, and the key returns to center after use. The separate Stop button provides local stop control when wired to the operator's stop/control circuit correctly.
This Genie key switch station may be used with select Genie commercial door operators that support an Open/Close key switch and Stop button control station. Compatibility should be verified by the operator model, control board, control voltage, wiring diagram, and required Stop circuit logic.
Do not order this station only because the existing control has a key and a Stop button. The mounting style, enclosure rating, key switch function, Stop circuit wiring, and operator control circuit must match. The Genie 107042.0004.S is an interior flush mount station with a center-return Open/Close key switch and Stop button.
If the current station is exterior-rated, surface mounted, stainless steel, non-keyed, three-push-button style, NEMA 4, NEMA 4X, NEMA 7/9, or tied into special interlock wiring, verify the correct replacement before ordering. Incorrect control station wiring can prevent the operator from running or create unsafe control behavior.
| Specification | Details |
|---|---|
| Brand | Genie |
| Part Number | 107042.0004.S |
| Gate Openers Unlimited Item ID | MMTC-1KFS |
| Product Type | Interior commercial key switch station with Stop button |
| Switch Function | Open / Close two-position key switch with center return |
| Stop Function | Separate Stop button on faceplate |
| Mounting Style | Flush mount |
| Application Location | Interior use |
| Enclosure Rating | NEMA 1 |
| Tamper-Proof Feature | Key required to remove cover |
| Faceplate | Brushed aluminum faceplate |
| Switch Rating | 15A @ 125/250VAC |
| Cylinder Type | Mortise type, 5 pin |
| Cylinder Dimensions | Approximately 1-1/8 in diameter x 1 in length |
| Approximate Faceplate Size | 4-3/4 in wide x 6 in tall |
| Approximate Box / Body Reference | 2-3/4 in wide x 5 in tall with 3-3/4 in body height reference; verify mounting depth before installation |
| Agency Approval | UL Listed |
Before replacing a commercial key switch station, inspect the full operator control circuit. A failed Stop circuit, open common wire, loose terminal, damaged key cylinder, wrong station type, or failed control board input can create symptoms that look like a bad wall station.
This part is easy to confuse with other Genie commercial key switch stations. The 107042.0004.S is the interior flush mount version with a Stop button. The similar 107042.0003.S is the interior flush mount key switch without the Stop button. Exterior versions and stainless faceplate versions use different part numbers and should not be substituted without checking the jobsite requirement.
The Stop circuit should be treated carefully. If the Stop circuit is open, disconnected, or wired incorrectly, the commercial operator may not respond to Open or Close commands. That does not always mean the new station is defective.
This key switch station should be installed by a qualified commercial door, low-voltage, or electrical technician familiar with commercial operator control circuits. Power should be turned off before service, and wiring should follow the operator manual, station wiring diagram, and local electrical requirements.
Do not bypass photo eyes, sensing edges, Stop circuits, interlocks, door reversal systems, monitored safety inputs, or other safety devices to make the operator run. If the door does not respond after station replacement, the operator control circuit should be diagnosed safely by a qualified technician.
A commercial door key switch station is only one part of the operator control system. If the door is moving unexpectedly, failing to stop, failing to reverse, or not responding to commands, stop using the equipment until the door, operator, wiring, Stop circuit, and safety devices are checked. Commercial doors are heavy, and unsafe control wiring can create a serious hazard.
For South Florida customers, local pickup in the Hialeah Gardens area may be available when inventory allows. Confirm availability, item ID, and part number before coming in for pickup.
Yes. The Genie 107042.0004.S is an interior NEMA 1 flush mount key switch station for select Genie commercial door operator control circuits.
Yes. This model includes a separate Stop button below the Open/Close key switch. Do not confuse it with similar key switch stations that do not include the Stop button.
On this station, tamper-proof means the key is required to remove the cover. This helps restrict access to the cover, mounting screws, and internal wiring.
No. The 107042.0004.S includes a Stop button. The 107042.0003.S is a similar interior flush mount tamper-proof key switch without the Stop button.
No. This is an interior NEMA 1 station. For exterior, wet, washdown, or exposed locations, verify the correct outdoor-rated Genie key switch station instead.
No. This is a two-position Open/Close key switch with a separate Stop button. It is not the same as a three-push-button Open/Close/Stop control station.
No. This part is intended for select Genie commercial door operator control circuits. It should not be used as a residential wall console, wireless keypad, or residential opener push button replacement.
Confirm the 107042.0004.S part number, interior flush mount requirement, NEMA 1 location, Stop button requirement, operator wiring diagram, control voltage, mounting depth, and whether the job needs an exterior, surface mount, stainless, or higher-rated station.