Genie GE-113433.0001.S Front Actuator Arm Bracket for GLA24V Gate Operators

Genie GE-113433.0001.S Front Actuator Arm Bracket

The Genie GE-113433.0001.S is a front actuator arm bracket for select Genie GLA24V linear actuator swing gate operator service repairs. Genie service-parts documentation lists 113433.0001.S as the front actuator arm bracket, making this a mechanical mounting part used at the front/gate-side actuator connection where the parts diagram confirms fitment.

This is a bracket service part only. It is not the complete actuator arm, rear actuator bracket, push open bracket, control box, post mount kit, battery kit, gate operator, or safety device. Match this part by exact part number, operator model, front bracket location, mounting geometry, gate swing layout, and existing hardware before ordering.

Primary Use

• Replacement front actuator arm bracket for select Genie GLA24V linear actuator swing gate operator installations
• Used at the front or gate-side actuator mounting location where 113433.0001.S is listed in the service parts diagram
• Helps secure the actuator arm to the gate-side mounting point when the original bracket is bent, worn, cracked, damaged, or missing
• Used in repairs where the original bracket is marked, ordered, or cross-referenced as 113433.0001.S
• Applies only where the gate frame, actuator geometry, and Genie installation dimensions support this bracket

Compatible With

Use this bracket only where the installed Genie operator and parts documentation confirm 113433.0001.S as the correct front actuator arm bracket. Do not assume it fits every Genie swing gate operator, slide gate operator, or non-Genie linear actuator system.

• Select Genie GLA24V residential linear actuator swing gate operator installations where the service parts list shows 113433.0001.S
• Repairs where the existing bracket is the front actuator arm bracket and not the rear bracket or push open bracket
• Applications where the gate-side mounting point, actuator pin location, bracket angle, and gate frame match the Genie installation requirements
• Single or dual GLA24V installations where the specific gate leaf uses this front bracket and the parts diagram confirms fitment

Features and Specifications

Important Comparison With Similar Genie Brackets

Genie actuator brackets can look similar but are used in different locations. Ordering the wrong bracket can create poor actuator geometry, travel problems, binding, or bracket damage.

• GE-113433.0001.S / 113433.0001.S: Front actuator arm bracket for select GLA24V applications.
• 113434.0001.S: Rear actuator arm bracket. This is a related but different bracket and should not be substituted for the front bracket without confirming the parts diagram.
• 113374.0001.S: Push open bracket for supported push-to-open GLA24V installations. This is not the same as the standard front actuator bracket.
• 113435.0001.S: Post mount actuator control box kit. This is a mounting accessory and not the front actuator arm bracket.
• GLA24V actuator arm: Not the same part. The actuator arm is a separate component from the front bracket.
• Complete GLA24V single or dual kit: Not the same item. This listing should be treated as the front bracket service part only.

Also Known As / Related Part Numbers

• GE-113433.0001.S
• 113433.0001.S
• GE1134330001S
• 1134330001S
• Genie GE-113433.0001.S
• Genie 113433.0001.S
• Genie front actuator arm bracket
• Bracket, Actuator Arm, Front
• Front actuator bracket for Genie GLA24V
• Genie GLA24V gate-side actuator bracket
• Genie linear actuator front mounting bracket
• 113434.0001.S - related rear actuator arm bracket, not the same part
• 113374.0001.S - related push open bracket, not the same front actuator bracket
• 113435.0001.S - related post mount kit, not the same part

Technician Notes

• Confirm the operator is a Genie GLA24V before ordering this bracket. Do not assume it fits GRSW24V, GRSL24V, GCSW36V, GCSL36V, or other actuator systems.
• Verify that the damaged or missing part is the front actuator bracket, not the rear bracket or optional push open bracket.
• Inspect the gate frame where the bracket mounts. A bent bracket may be a symptom of a weak gate frame, cracked weld, loose fasteners, gate sag, or incorrect actuator geometry.
• Check the actuator pin, clevis, bushings, cotter clips, and related hardware for wear before replacing only the bracket.
• If the bracket was bent, inspect for binding at full open and full close. The actuator should not bottom out, rub, twist, or force the bracket past its intended travel.
• After replacement, verify manual gate movement, actuator alignment, open and close limits, force settings, safety-device function, and warning devices before returning the operator to service.
• Do not drill, weld, or modify the bracket unless the installation documentation and gate structure support the change. Poor geometry can damage the actuator or create unsafe gate movement.

Before Ordering Checklist

• Confirm the exact part number is GE-113433.0001.S or 113433.0001.S.
• Confirm the installed operator is a Genie GLA24V linear actuator swing gate operator.
• Confirm you need the front actuator arm bracket, not the rear bracket, push open bracket, post mount kit, or actuator arm.
• Confirm the gate-side mounting location, hole pattern, bracket angle, actuator pin location, and existing hardware match the parts diagram.
• Inspect the gate frame, welds, fasteners, hinges, gate stops, actuator arm, clevis, pins, and rear bracket before ordering only the front bracket.
• Confirm whether bolts, nuts, washers, pins, clips, bushings, or mounting hardware are included.
• Confirm the original bracket failure was not caused by gate binding, sagging hinges, wrong push-to-open geometry, actuator overtravel, or impact damage.

Professional Advisory

The front actuator arm bracket affects actuator alignment, gate travel, force, and safe operation. If the bracket is bent, torn loose, repeatedly breaking, or mounted on a weak gate frame, have the gate inspected by a qualified gate operator technician before replacing parts. Do not force the operator to run with incorrect geometry, damaged brackets, missing pins, bypassed safety devices, or binding gate movement. After any bracket repair, monitored photo eyes, safety edges, inherent entrapment protection, limits, force settings, warning signs, and manual release operation should be verified.

Product Q&A

What is Genie GE-113433.0001.S used for?

Genie GE-113433.0001.S is the front actuator arm bracket for select Genie GLA24V linear actuator swing gate operator installations where the parts diagram lists 113433.0001.S.

Is GE-113433.0001.S the same as the rear actuator bracket?

No. GE-113433.0001.S is the front actuator arm bracket. The rear actuator arm bracket is a separate Genie service part and should not be treated as the same item.

Does this bracket fit every Genie swing gate operator?

No. This bracket should be matched to select Genie GLA24V applications where the service parts diagram confirms fitment. Do not assume it fits other Genie swing, slide, or commercial operator models.

Is this the same as the Genie push open bracket?

No. The push open bracket is a different Genie accessory used for supported push-to-open GLA24V installations. GE-113433.0001.S is the front actuator arm bracket.

Does this listing include the actuator arm or mounting hardware?

Do not assume the actuator arm, pins, bolts, washers, nuts, clips, or mounting hardware are included. Treat this as the front bracket only unless the supplier package specifically lists additional parts.

What can cause a front actuator bracket to bend or break?

Common causes include gate binding, sagging hinges, weak gate frame material, incorrect bracket geometry, actuator overtravel, missing gate stops, impact damage, or worn actuator pins and hardware.

What should I check after replacing this bracket?

Check manual gate movement, actuator alignment, pin and clevis fit, open and close limits, force settings, gate stops, safety photo eyes, safety edges, warning devices, and full travel before returning the gate to service.