Genie GE-113440.0001.S Logic Board Assembly for 24V Gate Operators

Genie GE-113440.0001.S Logic Board Assembly

The Genie GE-113440.0001.S is a logic board assembly used with select Genie 24V gate operator service repairs. Genie service documentation lists 113440.0001.S as PCB Assy, Logic BD, making it the main logic/control board service part where the installed operator parts diagram confirms this exact replacement.

This is an electronic logic board assembly, not the 24V motor drive PCB, PCB mount, power supply, reset button, buzzer, control box enclosure, actuator arm, loop rack, receiver accessory, or complete control box assembly. Match this part by exact part number, operator model, board revision, connector layout, software/setup requirements, and supplier package contents before ordering.

Primary Use

• Replacement logic board assembly for select Genie 24V gate operator service repairs
• Used where the service parts diagram lists 113440.0001.S as the logic board assembly
• Supports the operator control functions, setup logic, accessory inputs, safety inputs, relay logic, and status functions where installed in a compatible Genie operator
• Service replacement when the original logic board is confirmed failed, damaged, corroded, water damaged, surge damaged, or no longer communicating properly with the operator system
• Used only after related power, battery, motor drive, wiring, accessory, and monitored safety-device issues have been checked

Compatible With

Use this logic board only where the installed Genie operator documentation confirms 113440.0001.S as the correct service part. Do not assume it fits every Genie gate operator, every Genie garage door opener, or every 24V gate opener.

• Select Genie GLA24V linear actuator swing gate operator service repairs where the parts diagram lists 113440.0001.S
• Select Genie GRSW24V residential swing gate operator service repairs where the parts diagram lists 113440.0001.S
• Select Genie GRSL24V residential slide gate operator service repairs where the parts diagram lists 113440.0001.S
• Repairs where the original board is marked, ordered, or cross-referenced as GE-113440.0001.S or 113440.0001.S
• Applications where the control enclosure, power supply, motor drive PCB, accessory wiring, monitored safety inputs, and board connector layout match the installed Genie parts diagram

Features and Specifications

Important Comparison With Similar Genie Control Parts

Genie gate operator electronics include several separate service parts. Similar names do not mean the parts are interchangeable. Confirm whether you need the logic board, motor drive board, power supply, PCB mount, reset button, or enclosure before ordering.

• GE-113440.0001.S / 113440.0001.S: Logic board assembly for select Genie 24V gate operator service repairs.
• 113429.0001.S: 24V motor drive PCB assembly. This is the motor drive board and is not the same as the logic board.
• 113428.0001.S: 24V drive PCB mount. This is a mechanical mounting part and is not the logic board.
• 113292.0001.S: Gate operator PCB mount. This is a board support/mounting part and not the logic board assembly.
• 113443.0001.S: 24V 350W power supply. This is a power component and does not replace the logic board.
• 113436.0001.S: Linear actuator reset button. This is a separate button/switch service part and not the logic board.
• 113442.0001.S: UL325 gate operator buzzer. This is an audible warning component and not the logic board.
• 113431.0001.S: Control box enclosure. This is the enclosure housing and not an electronic control board.
• Complete control box assembly: Not the same item. This listing should be treated as the logic board assembly only unless the supplier package confirms a larger assembly.

Also Known As / Related Part Numbers

• GE-113440.0001.S
• 113440.0001.S
• GE1134400001S
• 1134400001S
• Genie GE-113440.0001.S
• Genie 113440.0001.S
• Genie logic board assembly
• Genie gate operator logic board
• Genie control board circuit assembly
• PCB Assy, Logic BD
• Logic board for Genie 24V gate operator
• Control board for Genie GLA24V gate operator
• Control board for Genie GRSW24V gate operator
• Control board for Genie GRSL24V gate operator
• 113429.0001.S - related 24V motor drive PCB assembly, not the same part
• 113428.0001.S - related 24V drive PCB mount, not the same part
• 113292.0001.S - related gate operator PCB mount, not the same part
• 113443.0001.S - related 24V power supply, not the same part
• 113436.0001.S - related reset button, not the same part
• 113442.0001.S - related UL325 buzzer, not the same part
• 113431.0001.S - related control box enclosure, not the same part

Technician Notes

• Confirm the logic board is the failed component before ordering. Many gate issues that look like a board failure are caused by batteries, power supply faults, motor drive board issues, damaged wiring, accessories, or monitored safety devices.
• Check the board for corrosion, water marks, insect damage, burned components, surge damage, loose connectors, cracked solder joints, damaged display area, or overheated terminals.
• If the board failed from water intrusion, correct the enclosure, seals, conduit entries, grommets, drainage, and mounting before installing the replacement board.
• If the board failed after a power surge or lightning event, inspect the power supply, motor drive board, batteries, radio/accessory wiring, loop detector wiring, safety inputs, and grounding.
• Do not confuse the logic board with the motor drive PCB. The logic board handles operator control logic, while the separate motor drive board handles motor output in supported systems.
• Label every connector before removal. Logic board wiring may include power, motor drive communication, safety inputs, accessory power, radio, relay outputs, loop inputs, reset wiring, buzzer, and control inputs depending on the model.
• After replacement, verify travel setup, force settings, limits, motor direction, timer-to-close, auxiliary relays, transmitter programming, primary/secondary setup where used, monitored safety devices, and fault status.
• Do not bypass monitored photo eyes, monitored safety edges, reset circuits, fire inputs, fuses, grounding, or operator protections to make a gate run after board replacement.

Before Ordering Checklist

• Confirm the exact part number is GE-113440.0001.S or 113440.0001.S.
• Confirm the installed Genie operator model and service parts diagram list 113440.0001.S.
• Confirm you need the logic board assembly, not the motor drive PCB, power supply, PCB mount, reset button, buzzer, control enclosure, or complete operator kit.
• Confirm the existing board revision, connector layout, mounting location, display/status behavior, and wire harness match the replacement board.
• Test battery voltage under load, charger or power supply output, fuses, reset button, motor drive board, safety inputs, accessory wiring, and control wiring before replacing the board.
• Inspect for water intrusion, insects, corrosion, heat damage, lightning damage, loose terminals, rubbed wires, damaged connectors, and failed accessories.
• Confirm monitored photo eyes, safety edges, loop detectors, exit devices, receivers, keypads, relays, fire access inputs, and auxiliary accessories are not causing the fault.
• Confirm whether the package includes only the board or also includes mounts, screws, harnesses, labels, display parts, instructions, or other control components.

Professional Advisory

Logic board replacement involves operator electronics, battery power, accessory wiring, monitored safety inputs, relay outputs, setup menus, and moving-gate operation. Incorrect diagnosis or wiring can damage the new board, create nuisance faults, or cause unsafe gate movement. If the system has water intrusion, lightning damage, burned wiring, repeated blown fuses, unknown prior modifications, fire access wiring, accessory relay wiring, or monitored safety-device issues, have the operator inspected by a qualified gate technician. Do not bypass monitored photo eyes, safety edges, reset circuits, fire inputs, fuses, grounding, warning devices, or operator control protections during diagnosis or repair.

Product Q&A

What is Genie GE-113440.0001.S used for?

Genie GE-113440.0001.S is a logic board assembly used with select Genie 24V gate operator service repairs where the parts diagram lists 113440.0001.S.

Is GE-113440.0001.S the same as the motor drive board?

No. GE-113440.0001.S is the logic board assembly. The 24V motor drive PCB assembly is a separate Genie service part and should not be treated as the same board.

Which Genie operators use this logic board?

This part appears in select Genie 24V gate operator service parts diagrams, including GLA24V, GRSW24V, and GRSL24V documentation. Always confirm fitment by the installed model and parts diagram before ordering.

Does this logic board include the power supply or PCB mounts?

Do not assume the power supply, PCB mounts, screws, wiring harnesses, or control enclosure are included. Treat this item as the logic board assembly only unless the supplier package specifically lists additional parts.

Can a bad logic board cause a gate not to run?

Yes, but a no-run condition can also be caused by weak batteries, failed power supply, blown fuses, bad motor drive board, damaged wiring, safety faults, reset button issues, or accessory input problems.

What should I check before replacing this logic board?

Check the operator model, part number, batteries, power supply, fuses, reset button, motor drive board, safety inputs, accessory wiring, board connectors, water intrusion, corrosion, and operator fault status before replacing the board.

What should be checked after replacing the logic board?

After replacing the logic board, verify travel setup, force settings, motor direction, monitored safety devices, transmitter programming, relay settings, timer-to-close, battery backup, reset operation, and full gate travel.