HySecurity MX001127 is a flow control manifold kit for select HySecurity SwingRiser Single HRG 220 hydraulic gate operator applications. It is commonly listed as a manifold assembly or flow control kit used in the hydraulic control section of the SwingRiser Single system.
This part is associated with hydraulic flow management on the SwingRiser Single operator. Current product listings commonly describe MX001127 as including valves and a seal kit. Because hydraulic manifold components are model-specific and configuration-specific, this kit should be selected only after confirming the operator model, serial number, HRG 220 single configuration, and HySecurity parts diagram.
The flow control manifold helps regulate hydraulic oil flow within the SwingRiser Single hydraulic system. Proper hydraulic flow control is important for smooth gate movement, controlled travel, consistent operator behavior, and reduced strain on related hydraulic components.
A worn, contaminated, leaking, misadjusted, or incorrect flow control manifold can contribute to poor hydraulic performance. Symptoms may include uneven movement, poor speed control, erratic gate travel, hydraulic leakage around the manifold area, or issues after previous hydraulic service. Similar symptoms can also be caused by hydraulic hoses, fittings, pump pack issues, incorrect valve adjustment, cylinder wear, low or contaminated fluid, or gate mechanical binding.
Use HySecurity MX001127 only where the operator parts diagram, original installed part, or HySecurity documentation confirms this part number.
HySecurity SwingRiser Single HRG 220 models may include multiple versions and motor configurations. Confirm the parts diagram before ordering for any of the following model families:
MX001127 should not be selected only because the operator is a SwingRiser. This part is specifically associated with SwingRiser Single HRG 220 flow control manifold applications. SwingRiser Twin systems can use different flow control hardware and may require a different kit.
Do not confuse MX001127 with MX001128. MX001128 is commonly listed as a flow control kit for SwingRiser Twin applications and may include fittings to the flow divider manifold. MX001127 is for SwingRiser Single applications where the parts diagram confirms this part number.
| Feature / Specification | Details |
|---|---|
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX001127 |
| Product Type | Flow control manifold kit / manifold assembly |
| Common Description | Manifold assembly, SR 220 / flow control manifold for SwingRiser Single |
| Common Application | Select HySecurity SwingRiser Single HRG 220 hydraulic applications |
| Operator Family | SwingRiser Single, where listed by parts diagram |
| Hydraulic Function | Flow control for hydraulic operation |
| Commonly Listed Kit Contents | Valves and seal kit; verify current package contents before ordering |
| Electrical Rating | Not a standalone electrical component; verify solenoid/coil requirements separately if servicing hydraulic controls |
| Pressure / Adjustment Note | Hydraulic flow and valve adjustments should be performed only according to HySecurity service instructions by a qualified technician |
The correct related parts depend on the exact SwingRiser Single model, hydraulic configuration, and repair being performed. Inspect the hydraulic system before ordering only the manifold kit.
Before replacing the flow control manifold kit, confirm that the issue is actually in the manifold and not caused by low fluid, contaminated hydraulic oil, leaking hoses, damaged fittings, incorrect valve adjustment, pump pack wear, cylinder problems, gate binding, or a mechanical obstruction. Hydraulic symptoms can overlap, so replacing the manifold without a proper diagnosis may not correct the problem.
When servicing this part, keep hydraulic cleanliness in mind. Dirt or debris introduced into the system can damage valves, seals, fittings, and other hydraulic components. If valve adjustments are required, they should be made according to HySecurity service procedures, not by guessing or bypassing hydraulic controls.
Hydraulic manifold service on a SwingRiser operator should be handled by a qualified gate technician. This repair may involve hydraulic pressure, valve adjustment, heavy gate movement, hose routing, and safety-critical operator behavior. Do not bypass safety devices, hydraulic protections, limit controls, inherent entrapment systems, photo eyes, gate edges, or controller protections to test operation.
HySecurity MX001127 is commonly used as a flow control manifold kit for select SwingRiser Single HRG 220 gate operator applications. It should be used where the parts diagram confirms this part number.
MX001127 is commonly listed for SwingRiser Single applications. SwingRiser Twin systems commonly use a different related flow control kit, so verify the operator configuration before ordering.
Current listings commonly describe MX001127 as including valves and a seal kit. Package contents should still be verified before ordering because packaging and kit contents can change.
No. MX001127 is commonly listed for SwingRiser Single flow control applications, while MX001128 is commonly listed for SwingRiser Twin applications. They should not be treated as interchangeable unless HySecurity documentation confirms it.
It may be involved in flow control concerns, but slow or uneven movement can also be caused by low fluid, contaminated fluid, hose or fitting leaks, pump pack issues, cylinder problems, valve adjustment, gate binding, or mechanical wear. Diagnose the system before replacing the manifold.
No. MX001127 is a flow control manifold kit. It is not a pump pack, hydraulic motor, hydraulic cylinder, hose fitting kit, or electrical control board.
Yes. A qualified gate technician is recommended because this repair can involve hydraulic pressure, valve adjustment, heavy gate movement, and safety-critical operator performance.