HySecurity MX001128, MANIFOLD ASSY, BRAKING, SR 222
HySecurity MX001128 is a braking manifold assembly and flow control manifold kit for select HySecurity SwingRiser Twin HRG 222 hydraulic gate operator applications. Current product listings identify this part as "MANIFOLD ASSY, BRAKING, SR 222" and also describe it as a flow control kit for SwingRiser Twin systems.
This kit is commonly listed as including valves, a seal kit, and fittings to the flow divider manifold. Because SwingRiser Twin hydraulic systems rely on correct braking, flow control, and flow-divider behavior, this part should be selected only after confirming the operator model, serial number, HRG 222 configuration, manifold layout, and HySecurity parts diagram.
What This Braking Manifold Assembly Does
The braking manifold assembly is part of the hydraulic control system used on select SwingRiser Twin operators. In this type of system, hydraulic flow, braking behavior, and flow-divider function must work together so both gate leaves move properly and the operator maintains controlled movement.
A worn, leaking, contaminated, incorrectly installed, or incorrect manifold assembly can contribute to poor hydraulic performance. Possible symptoms may include uneven twin gate movement, inconsistent speed, poor braking behavior, hydraulic leakage around the manifold, abnormal pressure behavior, or problems after previous hydraulic service. Similar symptoms can also be caused by hydraulic hoses, fittings, flow divider valve issues, pump pack problems, cylinder wear, low or contaminated fluid, incorrect valve adjustment, or mechanical gate binding.
Compatible With
Use HySecurity MX001128 only where the operator parts diagram, original manifold assembly, or HySecurity documentation confirms this part number.
- Select HySecurity SwingRiser Twin HRG 222 applications where MX001128 is listed as the braking manifold assembly or flow control manifold kit.
- SwingRiser Twin hydraulic control repairs where the original manifold assembly is marked, listed, or cross-referenced as MX001128.
- Applications where the HySecurity parts diagram identifies MX001128 for the SwingRiser Twin braking manifold or flow control manifold area.
- Repairs where valves, seal kit, and fittings to the flow divider manifold are required for the approved SwingRiser Twin manifold assembly.
Possible SwingRiser Twin Model Family Use
HySecurity SwingRiser Twin models include multiple sizes and hydraulic configurations. Confirm the parts diagram before ordering for any of the following model families:
- HySecurity SwingRiser 14 Twin / HRG 222 configurations where the parts diagram lists MX001128.
- HySecurity SwingRiser 19 Twin / HRG 222 configurations where the parts diagram lists MX001128.
- HySecurity SwingRiser 30 Twin / HRG 222 configurations where the parts diagram lists MX001128.
- Other SwingRiser Twin HRG 222 configurations where HySecurity documentation confirms MX001128.
Important Compatibility Warning
MX001128 should not be selected only because the operator is a SwingRiser. This part is specifically associated with SwingRiser Twin / HRG 222 hydraulic manifold applications where the parts diagram confirms the part number. SwingRiser Single systems can use a different manifold kit.
Do not confuse MX001128 with MX001127. MX001127 is commonly associated with SwingRiser Single / HRG 220 flow control manifold applications. MX001128 is commonly associated with SwingRiser Twin / HRG 222 braking or flow control manifold applications and may include fittings to the flow divider manifold.
Similar Parts That Are Not Automatically Interchangeable
- mx001127-flow-control-manifold-kit-swingriser-single-hrg-220.html">HySecurity MX001127 - flow control manifold kit for SwingRiser Single / HRG 220; not the same as MX001128.
- mx000352-manifold-check-valve-cartridge.html">HySecurity MX000352 - manifold check valve cartridge; not the same as the complete braking manifold assembly.
- mx001258-1-8-inch-npt-flow-control-valve.html">HySecurity MX001258 - 1/8 inch NPT flow control valve; not the same as the manifold assembly kit.
- mx001255-manual-bypass-valve.html">HySecurity MX001255 - manual bypass valve; not the same as this braking manifold assembly.
- HySecurity MX000174 - 3000 PSI relief valve; not the same as this manifold kit.
- Flow divider valve components - related to SwingRiser Twin hydraulic control but not automatically the same as MX001128.
- Hydraulic hoses, fittings, pump packs, motors, and cylinders - related hydraulic components, but not interchangeable with this manifold assembly.
Not Intended For
- SwingRiser Single / HRG 220 applications unless the parts diagram specifically lists MX001128.
- SlideDriver, SlideSmart, StrongArm, HydraSwing, HydraLift, or HydraWedge operators unless the parts diagram specifically lists MX001128.
- Individual flow control valve replacement.
- Individual check valve cartridge replacement.
- Hydraulic hose or hose fitting kit replacement.
- Hydraulic pump pack replacement.
- Hydraulic cylinder or hydraulic motor replacement.
- Limit switch, reset switch, disconnect switch, sensor, controller, or electrical troubleshooting repairs.
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX001128 |
| Product Type | Braking manifold assembly / flow control manifold kit |
| Common Description | Manifold assembly, braking, SR 222 |
| Common Application | Select HySecurity SwingRiser Twin HRG 222 hydraulic applications |
| Operator Family | SwingRiser Twin, where listed by parts diagram |
| Hydraulic Function | Braking / flow control support for approved SwingRiser Twin hydraulic configurations |
| Commonly Listed Kit Contents | Valves, seal kit, and fittings to flow divider manifold; verify current package contents before ordering |
| Electrical Rating | Not a standalone electrical component; verify any solenoid or coil requirements separately if applicable |
| Hydraulic Service Note | Hydraulic pressure, flow, braking behavior, and flow-divider function should be diagnosed by a qualified technician |
Also Known As / Related Part Numbers
- MX001128
- HySecurity MX001128
- Nice HySecurity MX001128
- HYS-MX001128
- HYS-mx001128
- HySecurity manifold assembly, braking, SR 222
- HySecurity braking manifold assembly SR 222
- HySecurity SwingRiser Twin braking manifold assembly
- HySecurity manifold, flow control, SwingRiser Twin
- Flow Control Kit for SwingRiser Twin
- Manifold Flow Control Kit for SwingRiser Twin HRG 222
- MX001127 - related SwingRiser Single / HRG 220 flow control kit; not the same part
- HYS-MX001127 - related distributor SKU format for single applications; not the same part
Related Parts and Accessories
The correct related parts depend on the exact SwingRiser Twin model, hydraulic configuration, and repair being performed. Inspect the hydraulic system before ordering only the manifold assembly.
- MX001127 flow control manifold kit for SwingRiser Single - related single-system part, not interchangeable with MX001128 unless documentation confirms.
- Flow divider valve components - related to SwingRiser Twin hydraulic synchronization and braking behavior; verify exact part number separately.
- Hydraulic hose fittings - some MX001128 listings mention fittings to the flow divider manifold, but verify the included pieces.
- MX000352 check valve cartridge - related hydraulic valve, not the complete manifold kit.
- MX001258 1/8 inch NPT flow control valve - related valve, not the complete manifold assembly.
- Hydraulic pump pack assemblies - separate assemblies that may connect with the manifold area.
- Hydraulic hoses, cylinders, seals, fittings, and valves - verify exact part numbers before ordering separately.
Technician Note
Before replacing the MX001128 braking manifold assembly, confirm that the issue is actually in the manifold kit and not caused by a flow divider problem, low fluid, contaminated hydraulic oil, leaking hoses, damaged fittings, incorrect valve adjustment, pump pack wear, cylinder bypass, gate binding, or mechanical obstruction. SwingRiser Twin hydraulic symptoms can overlap because both leaves and the flow-divider circuit must work together.
Hydraulic cleanliness is critical. Dirt introduced into the manifold, valves, fittings, or flow-divider circuit can damage seals, valve cartridges, pump components, and cylinders. If braking or flow adjustments are required after service, they should be made according to HySecurity service procedures, not by guessing or bypassing hydraulic controls.
Before Ordering, Confirm
- The required part number is MX001128.
- The operator is a HySecurity SwingRiser Twin / HRG 222 configuration.
- The operator model and serial number match the parts diagram being used.
- The repair requires the braking manifold assembly or flow control manifold kit, not an individual valve, hose, fitting, pump pack, motor, or cylinder.
- The package includes the valves, seal kit, and fittings required for the repair.
- The operator is not a SwingRiser Single system requiring MX001127 or another single-operator manifold kit.
- The hydraulic concern is not being caused by leaking hoses, fittings, low fluid, contaminated fluid, gate binding, flow divider issues, or incorrect adjustment.
- Any required pressure, braking, or flow adjustment procedure is understood before service begins.
Installation and Service Notes
- Secure the gates and operator before servicing hydraulic components.
- Relieve hydraulic load according to the manufacturer's service procedure before opening hydraulic connections.
- Keep ports, fittings, hoses, manifold openings, and flow-divider connections clean during service.
- Do not mix up hose routing or fittings during reassembly.
- Do not use incorrect sealant or tape on hydraulic fittings unless specified by the manufacturer.
- Inspect hydraulic hoses, fittings, valves, seals, cylinders, and related components while the manifold area is accessible.
- After service, check for leaks, smooth twin-gate travel, proper speed, correct braking behavior, synchronization, and safe operator operation.
Professional Advisory
Hydraulic braking manifold service on a SwingRiser Twin operator should be handled by a qualified gate technician. This repair may involve hydraulic pressure, valve adjustment, flow-divider behavior, heavy gate movement, hose routing, and safety-critical operator performance. Do not bypass safety devices, hydraulic protections, limit controls, inherent entrapment systems, photo eyes, gate edges, or controller protections to test operation.
Product Questions & Answers
What is HySecurity MX001128 used for?
HySecurity MX001128 is commonly used as a braking manifold assembly or flow control manifold kit for select SwingRiser Twin HRG 222 hydraulic gate operator applications.
Is MX001128 for SwingRiser Single or SwingRiser Twin operators?
MX001128 is commonly listed for SwingRiser Twin applications. SwingRiser Single systems commonly use a different related manifold kit, so verify the operator configuration before ordering.
Does MX001128 include valves and fittings?
Current listings commonly describe MX001128 as including valves, a seal kit, and fittings to the flow divider manifold. Package contents should still be verified before ordering because packaging can change.
Is MX001128 the same as MX001127?
No. MX001128 is commonly associated with SwingRiser Twin / HRG 222 applications, while MX001127 is commonly associated with SwingRiser Single / HRG 220 applications. They should not be treated as interchangeable unless HySecurity documentation confirms it.
Can this manifold help with uneven SwingRiser Twin movement?
It may be involved in braking or flow-control concerns, but uneven movement can also be caused by flow divider issues, low fluid, contaminated fluid, hose or fitting leaks, pump pack problems, cylinder problems, valve adjustment, gate binding, or mechanical wear.
Is MX001128 an individual flow control valve?
No. MX001128 is a manifold assembly or kit. It should not be confused with an individual valve such as MX001258, MX000352, MX001255, or MX000174.
Should a technician install this braking manifold assembly?
Yes. A qualified gate technician is recommended because this repair can involve hydraulic pressure, braking adjustment, flow-divider connections, heavy twin-gate movement, and safety-critical operator performance.
