HySecurity MX001127, MANIFOLD ASSEMBLY, SR 220
HySecurity MX001127 is a flow control manifold kit for select HySecurity SwingRiser Single HRG 220 hydraulic gate operator applications. It is commonly listed as a manifold assembly or flow control kit used in the hydraulic control section of the SwingRiser Single system.
This part is associated with hydraulic flow management on the SwingRiser Single operator. Current product listings commonly describe MX001127 as including valves and a seal kit. Because hydraulic manifold components are model-specific and configuration-specific, this kit should be selected only after confirming the operator model, serial number, HRG 220 single configuration, and HySecurity parts diagram.
What This Flow Control Manifold Kit Does
The flow control manifold helps regulate hydraulic oil flow within the SwingRiser Single hydraulic system. Proper hydraulic flow control is important for smooth gate movement, controlled travel, consistent operator behavior, and reduced strain on related hydraulic components.
A worn, contaminated, leaking, misadjusted, or incorrect flow control manifold can contribute to poor hydraulic performance. Symptoms may include uneven movement, poor speed control, erratic gate travel, hydraulic leakage around the manifold area, or issues after previous hydraulic service. Similar symptoms can also be caused by hydraulic hoses, fittings, pump pack issues, incorrect valve adjustment, cylinder wear, low or contaminated fluid, or gate mechanical binding.
Compatible With
Use HySecurity MX001127 only where the operator parts diagram, original installed part, or HySecurity documentation confirms this part number.
- Select HySecurity SwingRiser Single HRG 220 applications where MX001127 is listed as the flow control manifold kit.
- SwingRiser Single hydraulic control repairs where the original manifold assembly is marked, listed, or cross-referenced as MX001127.
- Applications where the HySecurity parts diagram identifies MX001127 for the SwingRiser Single pump pack or flow control manifold area.
- Repairs where valves and seal kit service are required for the approved SwingRiser Single flow control manifold assembly.
Possible SwingRiser Single Model Family Use
HySecurity SwingRiser Single HRG 220 models may include multiple versions and motor configurations. Confirm the parts diagram before ordering for any of the following model families:
- HySecurity SwingRiser 14 Single / HRG 220-A where the parts diagram lists MX001127.
- HySecurity SwingRiser 19 Single / HRG 220-B where the parts diagram lists MX001127.
- HySecurity SwingRiser 30 Single / HRG 220-C where the parts diagram lists MX001127.
- Other SwingRiser Single HRG 220 configurations where HySecurity documentation confirms MX001127.
Important Compatibility Warning
MX001127 should not be selected only because the operator is a SwingRiser. This part is specifically associated with SwingRiser Single HRG 220 flow control manifold applications. SwingRiser Twin systems can use different flow control hardware and may require a different kit.
Do not confuse MX001127 with MX001128. MX001128 is commonly listed as a flow control kit for SwingRiser Twin applications and may include fittings to the flow divider manifold. MX001127 is for SwingRiser Single applications where the parts diagram confirms this part number.
Similar Parts That Are Not Automatically Interchangeable
- mx001128-braking-manifold-assembly-swingriser-twin-hrg-222.html">HySecurity MX001128 - flow control manifold kit for SwingRiser Twin; not the same as MX001127.
- HySecurity MX001132 - hose fittings kit for single operators; not the same as the flow control manifold kit.
- HySecurity MX001135 - hose fittings kit for twin operators; not the same as the flow control manifold kit.
- HySecurity MX001114 - 1/4 inch hydraulic hose; not the same as the manifold assembly.
- HySecurity MX001121 - brake manifold kit; not the same as the flow control manifold kit.
- Hydraulic pump pack assemblies - may connect near the manifold area but are not the same part as MX001127.
- Hydraulic motors and cylinders - separate hydraulic components and not interchangeable with the flow control manifold.
Not Intended For
- SwingRiser Twin applications unless the parts diagram specifically lists MX001127.
- SlideDriver, SlideSmart, StrongArm, HydraSwing, HydraLift, or HydraWedge operators unless the parts diagram specifically lists MX001127.
- Hydraulic hose replacement.
- Hydraulic hose fitting kit replacement.
- Hydraulic pump pack replacement.
- Hydraulic cylinder or hydraulic motor replacement.
- Limit switch, reset switch, disconnect switch, sensor, controller, or electrical troubleshooting repairs.
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX001127 |
| Product Type | Flow control manifold kit / manifold assembly |
| Common Description | Manifold assembly, SR 220 / flow control manifold for SwingRiser Single |
| Common Application | Select HySecurity SwingRiser Single HRG 220 hydraulic applications |
| Operator Family | SwingRiser Single, where listed by parts diagram |
| Hydraulic Function | Flow control for hydraulic operation |
| Commonly Listed Kit Contents | Valves and seal kit; verify current package contents before ordering |
| Electrical Rating | Not a standalone electrical component; verify solenoid/coil requirements separately if servicing hydraulic controls |
| Pressure / Adjustment Note | Hydraulic flow and valve adjustments should be performed only according to HySecurity service instructions by a qualified technician |
Also Known As / Related Part Numbers
- MX001127
- HySecurity MX001127
- Nice HySecurity MX001127
- HYS-MX001127
- HYS-mx001127
- HySecurity manifold assembly SR 220
- HySecurity manifold, flow control, SwingRiser Single
- Flow Control Kit for SwingRiser Single
- Manifold Flow Control SwingRiser Single
- Manifold Flow Control Kit for SwingRiser Single HRG 220
- MX001128 - related SwingRiser Twin flow control kit; not the same part
- HYS-MX001128 - related distributor SKU format for twin applications; not the same part
Related Parts and Accessories
The correct related parts depend on the exact SwingRiser Single model, hydraulic configuration, and repair being performed. Inspect the hydraulic system before ordering only the manifold kit.
- MX001128 flow control manifold kit for SwingRiser Twin - related twin-system part, not interchangeable with MX001127 unless documentation confirms.
- MX001132 hose fittings kit for single operators - separate fitting kit, not the manifold assembly.
- MX001114 1/4 inch hydraulic hose - related hydraulic hose, not the manifold assembly.
- MX001107 pressure gauge kit - useful for hydraulic pressure checks where specified by service procedure.
- Hydraulic pump pack assemblies - separate assemblies that may connect with the manifold area.
- Hydraulic valves, seals, fittings, and coils - verify exact part numbers before ordering separately.
Technician Note
Before replacing the flow control manifold kit, confirm that the issue is actually in the manifold and not caused by low fluid, contaminated hydraulic oil, leaking hoses, damaged fittings, incorrect valve adjustment, pump pack wear, cylinder problems, gate binding, or a mechanical obstruction. Hydraulic symptoms can overlap, so replacing the manifold without a proper diagnosis may not correct the problem.
When servicing this part, keep hydraulic cleanliness in mind. Dirt or debris introduced into the system can damage valves, seals, fittings, and other hydraulic components. If valve adjustments are required, they should be made according to HySecurity service procedures, not by guessing or bypassing hydraulic controls.
Before Ordering, Confirm
- The required part number is MX001127.
- The operator is a HySecurity SwingRiser Single HRG 220 configuration.
- The operator model and serial number match the parts diagram being used.
- The repair requires the flow control manifold kit, not a hose fitting kit, hose, pump pack, hydraulic motor, or cylinder.
- The package includes the valves and seal kit required for the repair.
- The operator is not a SwingRiser Twin system requiring a different flow control kit.
- The hydraulic concern is not being caused by leaking hoses, fittings, low fluid, contaminated fluid, gate binding, or incorrect adjustment.
- Any required pressure or flow adjustment procedure is understood before service begins.
Installation and Service Notes
- Secure the gate and operator before servicing hydraulic components.
- Relieve hydraulic load according to the manufacturer's service procedure before opening hydraulic connections.
- Keep ports, fittings, hoses, and manifold openings clean during service.
- Do not mix up hose routing or fittings during reassembly.
- Do not use the wrong sealant or tape on hydraulic fittings unless specified by the manufacturer.
- Inspect hydraulic hoses, fittings, valves, seals, and related components while the manifold area is accessible.
- After service, check for leaks, smooth travel, proper speed, correct stopping behavior, and safe operator operation.
Professional Advisory
Hydraulic manifold service on a SwingRiser operator should be handled by a qualified gate technician. This repair may involve hydraulic pressure, valve adjustment, heavy gate movement, hose routing, and safety-critical operator behavior. Do not bypass safety devices, hydraulic protections, limit controls, inherent entrapment systems, photo eyes, gate edges, or controller protections to test operation.
Product Questions & Answers
What is HySecurity MX001127 used for?
HySecurity MX001127 is commonly used as a flow control manifold kit for select SwingRiser Single HRG 220 gate operator applications. It should be used where the parts diagram confirms this part number.
Is MX001127 for SwingRiser Single or SwingRiser Twin operators?
MX001127 is commonly listed for SwingRiser Single applications. SwingRiser Twin systems commonly use a different related flow control kit, so verify the operator configuration before ordering.
Does MX001127 include valves and seals?
Current listings commonly describe MX001127 as including valves and a seal kit. Package contents should still be verified before ordering because packaging and kit contents can change.
Is MX001127 the same as MX001128?
No. MX001127 is commonly listed for SwingRiser Single flow control applications, while MX001128 is commonly listed for SwingRiser Twin applications. They should not be treated as interchangeable unless HySecurity documentation confirms it.
Can this manifold fix slow or uneven SwingRiser movement?
It may be involved in flow control concerns, but slow or uneven movement can also be caused by low fluid, contaminated fluid, hose or fitting leaks, pump pack issues, cylinder problems, valve adjustment, gate binding, or mechanical wear. Diagnose the system before replacing the manifold.
Is MX001127 a pump pack or hydraulic motor?
No. MX001127 is a flow control manifold kit. It is not a pump pack, hydraulic motor, hydraulic cylinder, hose fitting kit, or electrical control board.
Should a technician install this manifold kit?
Yes. A qualified gate technician is recommended because this repair can involve hydraulic pressure, valve adjustment, heavy gate movement, and safety-critical operator performance.
