The HySecurity MX001725 is a replacement 5HP, 60Hz, single-phase electric motor for select HySecurity and Nice HySecurity hydraulic gate operator systems. It is commonly listed as Motor, Electric, 60Hz, 5 hp, 1PH, 3450 RPM, 230VAC and is also shown in current listings with 208-230VAC / 230VAC voltage references.
This motor is part of the electric-to-hydraulic drive system used in compatible HySecurity operators. In a hydraulic gate operator, the electric motor drives the hydraulic pump so the pump pack can build pressure and move hydraulic fluid through the valves, hoses, manifolds, and hydraulic drive components. A 5HP motor is typically used in higher-load applications where the hydraulic system requires more power than smaller 1HP, 2HP, or DC motor configurations.
The MX001725 should be matched by HySecurity part number, operator model, serial number, motor nameplate, voltage, phase, frequency, horsepower, RPM, frame/mounting style, shaft/coupler arrangement, pump pack layout, and wiring. Do not order by 5HP motor alone. Similar motors may not match the HySecurity pump, coupler, capacitor circuit, mounting, controller output, or duty requirements.
The MX001725 electric motor provides the rotation needed to drive the hydraulic pump in compatible HySecurity hydraulic gate operators. The pump then supplies the pressure and flow needed for the operator to move the gate or hydraulic drive assembly, depending on the operator family and installation.
This is the electric motor only unless the current package specifically includes additional parts. It is not a complete pump pack, hydraulic motor, hose kit, controller board, capacitor kit, brake manifold, soft-start kit, contactor kit, or full operator rebuild kit. Replacing the motor can correct a failed motor, but it will not repair a seized pump, damaged motor coupler, bad capacitor, incorrect voltage, worn pump pack, leaking hydraulic hose, contaminated fluid, or a gate that is dragging or binding.
The HySecurity MX001725 is intended for select HySecurity / Nice HySecurity hydraulic operator applications that require a 5HP, 60Hz, single-phase, 3450 RPM electric motor. Compatibility depends on the exact operator model, serial number, motor nameplate, voltage, phase, RPM, shaft/coupler arrangement, pump pack layout, and current HySecurity parts documentation.
Do not assume MX001725 fits every HySecurity hydraulic operator. HySecurity operators may use different motor voltages, horsepower ratings, frame styles, RPM ratings, motor brands, start switches, capacitors, couplers, pump assemblies, and mounting layouts. Always confirm by parts diagram and motor tag before ordering.
MX001725 is a 5HP single-phase AC motor and should not be confused with smaller AC motors, DC motors, or three-phase motors used in other HySecurity systems.
If the operator has had a previous motor replacement, pump pack repair, or motor-to-pump coupler change, compare the installed motor nameplate and coupling setup instead of relying only on the operator model.
MX001725 should be selected by the HySecurity parts diagram and motor nameplate, not by horsepower alone. A 5HP single-phase motor from another source may not match the pump shaft, coupler, mounting, RPM, capacitor/start circuit, voltage, or duty requirements of the HySecurity operator.
If the motor failed, check the cause before installing the replacement. A seized pump, damaged coupler, failed capacitor, incorrect voltage, poor wiring connection, water intrusion, overloaded gate, or dragging gate can damage a replacement motor quickly.
| Feature / Specification | Details |
|---|---|
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX001725 |
| Product Type | Replacement electric motor |
| Common Description | Motor, Electric, 60Hz, 5 hp, 1PH, 3450 RPM, 230VAC |
| Horsepower | 5 HP |
| Frequency | 60Hz |
| Phase | Single-phase / 1 phase |
| Voltage Reference | 230VAC; some current listings reference 208-230VAC |
| RPM Reference | 3450 RPM commonly listed |
| System Type | AC electric motor for select hydraulic gate operator pump systems |
| Common Application | Select HySecurity hydraulic operator applications where the parts diagram confirms MX001725 |
| Function | Drives the hydraulic pump in compatible HySecurity hydraulic operator systems |
| Diagnosis Note | Motor failure should be diagnosed with capacitors, start circuit, voltage, wiring, pump load, and motor coupler condition included in the inspection |
| Included Items | Electric motor only unless the current supplier package specifically includes coupler hardware, capacitors, start switch, mounting hardware, threadlocker, anti-seize, labels, or instructions |
| Not Included Unless Listed | Hydraulic pump, pump pack, motor coupler, capacitors, start switch, hydraulic fluid, hoses, fittings, valves, controller board, contactor, relay, and mounting hardware unless separately listed |
A 5HP single-phase motor places a heavy load on the operator power circuit and hydraulic pump system. Before replacing the motor, check incoming voltage under load, breaker and disconnect condition, contactor/relay operation, capacitor circuit, start switch, wiring terminals, and motor windings.
If the motor runs but the operator does not build hydraulic pressure or move the gate, inspect the motor-to-pump coupler, hydraulic pump, fluid level, relief valve, hoses, quick disconnects, and pump pack. A seized pump, stripped coupler, or dragging gate can damage a new motor quickly.
Disconnect operator power and secure the gate before servicing the motor or pump pack. This motor may be connected to 230VAC single-phase power, and the start circuit may contain capacitors. Label wiring before removal and compare the replacement motor to the original motor nameplate before installation.
Inspect the motor-to-pump coupler, pump shaft, motor shaft, and mounting alignment before installing the replacement motor. After installation, verify proper motor rotation, normal hydraulic pressure response, smooth gate movement, no unusual noise, and no overheating. If the motor hums, labors, overheats, or trips protection, stop and diagnose the pump, capacitors, wiring, voltage, and gate load.
Replacing a 5HP single-phase motor in a hydraulic gate operator can involve high-current line voltage, capacitor circuits, moving gate parts, hydraulic pressure, rotating shafts, and sensitive controller electronics. A qualified HySecurity gate technician or electrician should handle the repair when the operator has repeated motor failures, start-circuit issues, hydraulic pressure problems, or unknown prior repairs.
Do not bypass fuses, contactors, relays, start switches, capacitors, controller protections, monitored entrapment protection, photo eyes, safety edges, limits, or disconnects to make the motor run. The motor and hydraulic system should be repaired correctly and fully tested before the gate is returned to service.
The HySecurity MX001725 is a 5HP, 60Hz, single-phase electric motor used in select HySecurity hydraulic gate operator systems where the parts diagram lists this motor.
MX001725 is commonly listed as a 230VAC motor, with some current listings referencing 208-230VAC. Always verify the motor nameplate and operator wiring before ordering.
Current listings commonly describe MX001725 as a 3450 RPM electric motor.
Yes. MX001725 is commonly listed as a 1PH / single-phase motor.
No. MX001725 is a 5HP single-phase motor. MX001912 is a related 2HP, 60Hz, single-phase motor kit. They should not be substituted without HySecurity parts-diagram confirmation.
It may help if the electric motor has failed, but no-move conditions can also be caused by bad capacitors, a failed start switch, incorrect voltage, damaged wiring, a seized pump, failed coupler, low hydraulic fluid, valve issues, worn drive components, or a dragging gate.