The LiftMaster myQ MYQW11AXXW is an indoor plug-in wireless chime that provides audible and visual notifications from select compatible myQ video access devices. It is useful when a phone is muted, charging, in another room, or not close enough for the user to hear a mobile notification.
The chime plugs directly into an indoor wall outlet and connects to a 2.4 GHz Wi-Fi network. Initial setup is completed through the myQ app using Bluetooth. No traditional doorbell wiring, separate speaker wiring, batteries, or mounting hardware are required for the chime itself.
Once paired with a compatible myQ device, the MYQW11AXXW plays a selected tone and can flash its LED when the connected device generates an alert. Tone, volume, LED behavior, and temporary Snooze settings are managed through the myQ app.
Multiple chimes can be added to different rooms or zones. This can improve alert coverage in larger homes, multi-level homes, detached work areas with indoor Wi-Fi coverage, or locations where the connected phone is not always nearby.
Compatibility requires a supported myQ device, current myQ app, myQ account, internet connection, and adequate 2.4 GHz Wi-Fi coverage. Verify the exact connected-device model before ordering.
Do not assume compatibility based only on the myQ name. Confirm the source device model and current myQ app support before purchasing the chime.
The chime can be configured to play a tone, flash its LED, or provide the alert behavior available through the current myQ app. Available settings may change with app or firmware updates.
The MYQW11AXXW connects to a 2.4 GHz Wi-Fi network only. It is not documented for direct connection to a 5 GHz-only network. A dual-band router may be usable when its 2.4 GHz network is enabled and properly configured.
Initial setup uses Bluetooth to connect the chime to the myQ app. The app then guides the user through Wi-Fi connection, device pairing, tone selection, volume adjustment, and LED configuration.
A strong Wi-Fi signal is required at the wall outlet where the chime will be installed. Weak signal, network isolation, changed Wi-Fi credentials, router replacement, or unsupported security settings can prevent setup or cause intermittent operation.
| Specification | Details |
|---|---|
| Brand | LiftMaster myQ |
| Model Number | MYQW11AXXW |
| Product Type | Indoor plug-in wireless chime |
| Primary Function | Audible and visual alerts from compatible myQ devices |
| Wi-Fi Connectivity | 2.4 GHz Wi-Fi only |
| Setup Connection | Bluetooth setup through the myQ app |
| Power Input | 100-240 VAC, 50/60 Hz, 1A |
| U.S. Installation Power | Plug directly into a standard 120V AC wall outlet as directed by the U.S. manual |
| Mounting Style | Direct wall-outlet plug-in |
| Battery Required | No |
| Traditional Doorbell Wiring Required | No |
| Audio Output | 77 dB at 1 meter |
| Volume | Adjustable through the myQ app |
| Chime Tones | Multiple selectable tone options |
| Visual Indicator | Multi-color status and alert LED |
| Snooze Function | Temporary alert silencing through the myQ app |
| Multiple Chime Support | Yes, multiple chimes may be added for separate rooms or zones |
| Operating Temperature | 32 F to 113 F (0 C to 45 C) |
| Installation Environment | Indoor use only |
| Color | White |
| Reset Control | Side-mounted setup and factory-reset button |
| Warranty | 1-year limited warranty, subject to current manufacturer terms |
| LED Condition | Meaning |
|---|---|
| Solid White | Device is starting |
| Blinking Blue | Ready for pairing |
| Solid Blue | Bluetooth connected |
| Alternating Blue and Green | Connecting to Wi-Fi |
| Blinking Green | Connecting to the myQ app |
| Solid Green | Successfully connected to the myQ app |
| Blinking Magenta | Firmware update in progress |
| Pulsing Blue | Chime alert or tone is active when enabled |
| Solid Red | Factory reset |
| No Light | Power is off or the LED has been disabled in the app |
To update the Wi-Fi connection, press and hold the side button until the LED becomes solid blue, then release it to enter setup mode. The myQ app can then be used to enter the current Wi-Fi credentials.
A factory reset removes saved settings and returns the chime to an unconfigured state. Press and hold the reset button until the LED becomes solid red, then release it. The chime must be set up and paired again after the reset.
The MYQW11AXXW is intended for indoor use only. Plug it directly into a suitable wall outlet. Do not use the chime with an extension cord, power strip, damaged outlet, loose receptacle, or location exposed to water or excessive moisture.
Do not install it outdoors, inside an unconditioned gate-operator cabinet, in a wet garage location, or where irrigation, condensation, or rain may reach the device. The published minimum operating temperature is 32 F.
The compatible myQ Video Doorbell, Smart Garage Video Keypad, Secure View 3-in-1 Smart Lock, mobile device, Wi-Fi router, internet service, and myQ account are not included. Printed documentation or package inserts may vary by production revision.
The MYQW11AXXW receives alerts through the compatible myQ ecosystem. It is not a universal dry-contact chime, wired doorbell transformer accessory, gate alarm, or radio receiver.
A chime that does not sound is not always defective. First verify the app volume, Snooze setting, source-device alert configuration, Wi-Fi connection, outlet power, and paired-device status.
If the chime works near the router but not at the intended outlet, the problem is likely Wi-Fi coverage rather than the chime speaker. Relocate the chime or improve the 2.4 GHz network signal before replacing the accessory.
Do not open or modify the chime housing. Stop using the device if the plug, housing, outlet connection, or internal electronics appear damaged or become unusually hot.
A loose, damaged, discolored, sparking, or overheating wall outlet should be inspected by a qualified electrician. The chime should not be used to conceal or continue using an unsafe receptacle.
LiftMaster confirms compatibility with the myQ Video Doorbell, myQ Smart Garage Video Keypad, and Secure View 3-in-1 Video Lock. Verify the exact source-device model and current myQ app support before ordering.
No. The chime plugs directly into an indoor wall outlet and receives alerts wirelessly through the compatible myQ system. It does not connect to traditional doorbell wiring.
The MYQW11AXXW requires a 2.4 GHz Wi-Fi network. A dual-band router may be used when its 2.4 GHz network is enabled and available at the chime location.
Yes. The myQ app provides selectable tone options, adjustable volume, LED behavior settings, and a temporary Snooze function.
Yes. Multiple chimes can be added to provide audible and visual alerts in different rooms, floors, or zones, provided each location has suitable outlet power and Wi-Fi coverage.
No. The MYQW11AXXW is for indoor use only and has a published operating range of 32 F to 113 F. Do not install it where it can be exposed to rain, irrigation, condensation, or excessive moisture.
An alternating blue and green LED indicates that the chime is connecting to Wi-Fi. If the pattern continues, unplug the chime for 10 seconds, reconnect it, and verify the Wi-Fi settings and signal strength.
The standalone product is one MYQW11AXXW plug-in myQ Chime. A compatible doorbell, video keypad, smart lock, mobile device, Wi-Fi router, and internet service are not included.