The HySecurity MX001395 is a replacement 24VDC electric motor used on HySecurity SwingSmart DC gate operators. Official HySecurity SwingSmart DC parts documentation lists MX001395 as Motor, Electric, 24VDC for SwingSmart DC models. Public distributor listings commonly describe this motor as a 24VDC, 350W, approximately 2700 RPM replacement motor for SwingSmart DC systems.
This motor is part of the SwingSmart DC drive system. The operator uses a 24VDC motor, motor pulley, drive belt, gearbox pulley, gearbox, taper clamp assembly, and gate arm hardware to move the swing gate. When the motor is weak, worn, burned, contaminated, or no longer running correctly, the operator may show symptoms such as weak gate movement, intermittent travel, motor stall, no motor output, excessive noise, arcing, overheating, or failure to move the gate under load.
The MX001395 motor should be matched by HySecurity part number and the correct SwingSmart DC parts diagram. This is not a complete gate operator, gearbox, control board, pulley kit, belt, arm assembly, battery, charger, or full drive assembly. It is a motor replacement component and should be installed only after confirming that the motor is the failed part and not a symptom of a gate, battery, charger, controller, belt, pulley, gearbox, or arm-geometry issue.
The HySecurity MX001395 electric motor is commonly associated with the following operator and service applications:
| Manufacturer | HySecurity / Nice HySecurity |
|---|---|
| Part Number | MX001395 |
| Product Type | Electric Motor / Replacement Drive Motor |
| Common Description | Motor, Electric, 24VDC / 24VDC 350W 2700RPM Motor |
| Voltage | 24VDC |
| Power Rating | 350W, commonly shown in public distributor listings |
| Speed | Approximately 2700 RPM, commonly shown in public distributor listings |
| Compatible Operator Family | HySecurity SwingSmart DC, where MX001395 is shown in the parts diagram |
| Operator Type | Swing gate operator |
| Drive System Application | Motor power source for the SwingSmart DC belt, pulley, gearbox, and gate arm drive assembly |
| Operator Gearbox Reference | SwingSmart DC product information describes the operator drive as a 24VDC motor driving a 600:1 gearbox |
| Included Items | Replacement motor only, unless otherwise stated by the product listing |
| Related Gearbox | MX002005 SwingSmart DC gearbox is a related separate part, not included unless stated |
| Related Belt | MX001744 drive belt is a related separate part, not included unless stated |
| Related Motor Pulley | MX001403 24T motor pulley is a related separate part, not included unless stated |
| Important Notes | Verify operator model, parts diagram, motor condition, pulley condition, belt condition, gearbox condition, battery voltage, charger operation, and gate movement before ordering. |
Depending on why the motor is being replaced, the following related components may also need to be inspected:
A SwingSmart DC motor failure should be diagnosed as part of the full drive and power system. Before replacing the motor, check battery voltage under load, charger operation, control board motor output, motor wiring, drive belt, motor pulley, gearbox pulley, gearbox condition, taper clamp setting, and mechanical gate movement. A weak battery, bad charger, damaged gearbox, worn belt, seized gate, or binding arm can create symptoms that look like a failed motor.
If the motor is noisy, weak, hot, arcing, or intermittent, inspect the motor brushes and commutator condition as well. HySecurity MX001920 is commonly listed as the related 24VDC motor brush kit. If the motor has burned windings, heavy internal damage, seized bearings, water intrusion, or severe shaft damage, replacing the complete motor may be more appropriate than replacing brushes only.
Motor replacement involves internal electrical and drive components. Disconnect all power sources before service, including AC power, DC battery power, and any connected solar charging circuit. A swing gate can move unexpectedly if power remains connected or if the gate is under load.
After replacing the motor, check motor wiring, belt tracking, pulley alignment, gearbox operation, taper clamp adjustment, gate arm travel, limits, stops, and all required safety devices before returning the operator to service. If the motor failed from low voltage, mechanical binding, water intrusion, overload, or poor arm geometry, the underlying problem should be corrected by a qualified gate technician.
The HySecurity MX001395 is a replacement 24VDC electric motor used on SwingSmart DC gate operators.
Official HySecurity SwingSmart DC parts documentation lists MX001395 as Motor, Electric, 24VDC for SwingSmart DC models. Always verify the parts diagram before ordering.
Public distributor listings commonly describe MX001395 as a 24VDC, 350W motor with an approximate speed of 2700 RPM.
No. MX001395 is the electric motor. The SwingSmart DC gearbox is a separate part, commonly listed as MX002005.
The motor pulley should be verified against your stocked listing. The related SwingSmart DC motor pulley is commonly listed separately as MX001403.
Yes. Worn or contaminated motor brushes can cause weak operation, intermittent movement, arcing, noise, or motor stall symptoms. The related brush kit is commonly listed as MX001920.
Inspect the batteries, charger, control board output, motor wiring, drive belt, pulleys, gearbox, taper clamp assembly, gate arm hardware, limits, mechanical stops, and overall gate movement before replacing the motor.