The HySecurity MX001639 is a replacement 5HP, 60Hz, three-phase electric motor for select HySecurity and Nice HySecurity hydraulic gate operator systems. It is commonly listed as Motor, Electric, 60Hz, 5 hp, 3PH, 3450 RPM, 208-230/460VAC.
This motor is part of the electric-to-hydraulic drive system used in compatible HySecurity operators. In a hydraulic gate operator or hydraulic supply system, the electric motor drives the hydraulic pump so the pump pack can build pressure and move hydraulic fluid through the valves, hoses, manifolds, and hydraulic drive components. A 5HP three-phase motor is used in higher-load applications where the operator electrical system is built for three-phase power.
HySecurity HydraSupply XL parts documentation lists MX001639 for Twin model applications, and current listings commonly describe it as a 5HP Baldor electric motor. Because motor fitment depends on the installed operator, pump pack, voltage configuration, and control system, MX001639 should be matched by parts diagram and motor nameplate before ordering.
The MX001639 electric motor provides the rotation needed to drive the hydraulic pump in compatible HySecurity hydraulic systems. The pump then supplies the pressure and flow needed for the operator to move the gate or hydraulic drive assembly, depending on the operator family and installation.
This is the electric motor only unless the current package specifically includes additional parts. It is not a complete pump pack, hydraulic motor, hose kit, controller board, braking manifold, soft-start kit, contactor kit, VFD, overload, or full operator rebuild kit. Replacing the motor can correct a failed motor, but it will not repair a seized pump, damaged motor coupler, incorrect incoming voltage, failed contactor, bad overload, VFD fault, worn pump pack, leaking hydraulic hose, contaminated fluid, or a gate that is dragging or binding.
The HySecurity MX001639 is intended for select HySecurity / Nice HySecurity hydraulic operator applications that require a 5HP, 60Hz, three-phase, 3450 RPM electric motor. Compatibility depends on the exact operator model, serial number, motor nameplate, voltage, phase, RPM, shaft/coupler arrangement, pump pack layout, and current HySecurity parts documentation.
Do not assume MX001639 fits every HySecurity hydraulic operator. HySecurity operators may use different motor voltages, horsepower ratings, frame styles, RPM ratings, motor brands, contactors, overloads, VFD controls, couplers, pump assemblies, and mounting layouts. Always confirm by parts diagram and motor tag before ordering.
MX001639 is a 5HP three-phase AC motor and should not be confused with single-phase motors, DC motors, or lower-horsepower motors used in other HySecurity systems.
If the operator has had a previous motor replacement, pump pack repair, voltage conversion, VFD replacement, or motor-to-pump coupler change, compare the installed motor nameplate and coupling setup instead of relying only on the operator model.
MX001639 should be selected by the HySecurity parts diagram and motor nameplate, not by horsepower alone. A 5HP three-phase motor from another source may not match the pump shaft, coupler, mounting, RPM, voltage, service factor, insulation, enclosure style, control system, or duty requirements of the HySecurity operator.
If the motor failed, check the cause before installing the replacement. A seized pump, damaged coupler, incorrect voltage, phase loss, failed contactor, overload issue, VFD fault, poor wiring connection, water intrusion, overloaded gate, or dragging gate can damage a replacement motor quickly.
| Feature / Specification | Details |
|---|---|
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX001639 |
| Product Type | Replacement electric motor |
| Common Description | Motor, Electric, 60Hz, 5 hp, 3PH, 3450 RPM, 208-230/460VAC |
| Horsepower | 5 HP |
| Frequency | 60Hz |
| Phase | Three-phase / 3PH |
| Voltage Reference | 208-230/460VAC commonly listed |
| RPM Reference | 3450 RPM commonly listed |
| Motor Brand Reference | Current listings commonly describe this as a Baldor electric motor; verify motor tag before ordering |
| Primary Documented Application | HydraSupply XL Twin models where MX001639 is listed in HySecurity parts documentation |
| System Type | AC three-phase electric motor for select hydraulic pump systems |
| Function | Drives the hydraulic pump in compatible HySecurity hydraulic operator systems |
| Diagnosis Note | Motor failure should be diagnosed with phase balance, voltage, contactor, overload/VFD, wiring, pump load, and motor coupler condition included in the inspection |
| Included Items | Electric motor only unless the current supplier package specifically includes coupler hardware, mounting hardware, threadlocker, anti-seize, labels, or instructions |
| Not Included Unless Listed | Hydraulic pump, pump pack, motor coupler, hydraulic fluid, hoses, fittings, valves, controller board, contactor, overload, VFD, disconnect, and mounting hardware unless separately listed |
A 5HP three-phase motor should be diagnosed with the full power circuit included. Check all three phases, phase balance, incoming voltage under load, disconnect condition, breaker/fuse condition, contactor operation, overload setting, VFD status where used, wiring terminals, and motor windings before replacing the motor.
If the motor runs but the operator does not build hydraulic pressure or move the gate, inspect the motor-to-pump coupler, hydraulic pump, fluid level, relief valve, hoses, quick disconnects, and pump pack. A seized pump, stripped coupler, or dragging gate can damage a new motor quickly.
Disconnect operator power and secure the gate before servicing the motor or pump pack. This motor may be connected to 208-230VAC or 460VAC three-phase power. Label wiring before removal and compare the replacement motor to the original motor nameplate before installation.
Inspect the motor-to-pump coupler, pump shaft, motor shaft, and mounting alignment before installing the replacement motor. After installation, verify correct motor rotation, normal hydraulic pressure response, smooth gate movement, no unusual noise, and no overheating. If the motor runs backward, hums, labors, overheats, trips an overload, or faults a VFD, stop and diagnose the phase wiring, pump load, voltage, and gate condition.
Replacing a 5HP three-phase motor in a hydraulic gate operator can involve high-current three-phase line voltage, moving gate parts, hydraulic pressure, rotating shafts, and sensitive controller electronics. A qualified HySecurity gate technician or electrician should handle the repair when the operator has repeated motor failures, phase-loss issues, overload trips, VFD faults, hydraulic pressure problems, or unknown prior repairs.
Do not bypass fuses, contactors, overloads, VFD protections, controller protections, monitored entrapment protection, photo eyes, safety edges, limits, or disconnects to make the motor run. The motor and hydraulic system should be repaired correctly and fully tested before the gate is returned to service.
The HySecurity MX001639 is a 5HP, 60Hz, three-phase electric motor used in select HySecurity hydraulic gate operator systems where the parts diagram lists this motor.
MX001639 is commonly listed as a 208-230/460VAC motor. Always verify the motor nameplate and operator wiring before ordering.
Current listings commonly describe MX001639 as a 3450 RPM electric motor.
Yes. MX001639 is commonly listed as a 3PH / three-phase motor.
No. MX001639 is a 5HP three-phase motor. MX001725 is a related 5HP single-phase motor. They should not be substituted without HySecurity parts-diagram and electrical-system confirmation.
It may help if the electric motor has failed, but no-move conditions can also be caused by phase loss, contactor or overload failure, VFD faults, incorrect voltage, damaged wiring, a seized pump, failed coupler, low hydraulic fluid, valve issues, worn drive components, or a dragging gate.