HySecurity MX002467, EYEBOLT, REPLACEMENT,NORD-LOCK

HySecurity MX002467, EYEBOLT, REPLACEMENT,NORD-LOCK

HySecurity MX002467 is a cylinder anchor eyebolt hardware assembly for select HySecurity StrongArm barrier gate operator applications. HySecurity parts documentation lists MX002467 as "Eyebolt, Nut and Nord-Lock, Cylinder Anchor" for StrongArm models manufactured after 3/25/2011.

Current listings describe this part as a 1 inch cylinder anchor adjustment part that includes the eyebolt, 2 nuts, and 2 Nord-Lock washers. Because this hardware anchors and adjusts the hydraulic cylinder mount, it should be matched carefully by operator model, manufacture date, cylinder anchor arrangement, and parts diagram.

What This Cylinder Anchor Eyebolt Does

The MX002467 eyebolt assembly anchors and adjusts the hydraulic cylinder at the approved mount location on select StrongArm operators. The eyebolt, nuts, and Nord-Lock washers work together to provide the correct mechanical connection and locking hardware for the cylinder anchor point where HySecurity specifies this part.

A worn, bent, loose, missing, cross-threaded, or incorrect cylinder anchor eyebolt can affect cylinder alignment, arm movement, hardware retention, and hydraulic drive performance. Similar symptoms can also be caused by worn cylinder pins, loose crankshaft hardware, damaged cylinder rod ends, worn bearings, loose yokes, damaged arm brackets, incorrect arm balance, or prior non-factory repairs.

Compatible With

Use HySecurity MX002467 only where the operator parts diagram, original cylinder anchor hardware, or HySecurity documentation confirms this part number.

• Select HySecurity StrongArm barrier gate operator applications where MX002467 is listed as the cylinder anchor eyebolt, nut and Nord-Lock assembly.
• HySecurity StrongArm models manufactured after 3/25/2011 where the parts diagram lists MX002467.
• StrongArm cylinder anchor repairs where the original hardware is marked, listed, or cross-referenced as HySecurity MX002467.
• Applications where the 1 inch cylinder anchor hardware, eyebolt, nuts, Nord-Lock washers, and mount arrangement match the HySecurity parts diagram.
• Repairs where diagnosis confirms the cylinder anchor eyebolt hardware is worn, damaged, loose, or no longer serviceable.

Important Compatibility Warning

Do not order MX002467 based only on the word "eyebolt." This is a cylinder anchor hardware assembly with Nord-Lock washers for specific StrongArm applications. It should not be replaced with a generic eyebolt, ordinary flat washers, split lock washers, or random hardware-store fasteners.

The manufacture date matters. HySecurity parts documentation lists MX002467 for StrongArm models manufactured after 3/25/2011. Earlier StrongArm units may use different cylinder anchor hardware, so confirm the serial number and parts diagram before ordering.

Similar Parts That Are Not Automatically Interchangeable

• Generic eyebolts - not confirmed substitutes for the HySecurity cylinder anchor hardware.
• Generic nuts or standard washers - not the same as the specified nut and Nord-Lock washer assembly.
• HySecurity MX000077 - StrongArm hydraulic cylinder assembly; not the same as MX002467.
• HySecurity MX000312 - stainless steel cylinder pin for StrongArm references; related linkage hardware, not the cylinder anchor eyebolt.
• HySecurity MX001100 - crankshaft with bearing, zerk and keys; related arm-drive component, not the cylinder anchor eyebolt.
• HySecurity MX000306 - 4-bolt crankshaft bearing; not the same as this eyebolt assembly.
• HySecurity MX000299 - limit cam; related travel/limit component, not the cylinder anchor hardware.
• HySecurity MX001000 or MX001386 hose kit references - related hydraulic hose parts, not the cylinder anchor hardware.
• Arm brackets, yokes, counterweights, and complete barrier arms - related StrongArm hardware but not interchangeable with MX002467.

Not Intended For

• StrongArm models manufactured before 3/25/2011 unless the current parts diagram specifically lists MX002467.
• StrongArm M30/M50, StrongArmPark, SwingRiser, HydraSwing, HydraLift, HydraWedge, SlideDriver, SlideSmart, SwingSmart, or WedgeSmart operators unless the parts diagram specifically lists MX002467.
• Hydraulic cylinder replacement.
• Cylinder pin replacement.
• Crankshaft, crank bearing, or limit cam replacement.
• Hydraulic hose, pump pack, manifold, or valve replacement.
• Side-mount arm bracket, yoke bracket, counterweight, or complete barrier arm replacement.
• General-purpose eyebolt, nut, washer, or fastener replacement not shown in the HySecurity parts diagram.

Features & Specifications

Also Known As / Related Part Numbers

• MX002467
• HySecurity MX002467
• Nice HySecurity MX002467
• HYS-MX002467
• HYS-mx002467
• MX002467-5128
• HySecurity eyebolt replacement Nord-Lock
• HySecurity eyebolt, nut and Nord-Lock, cylinder anchor
• HySecurity cylinder anchor eyebolt
• HySecurity cylinder anchor eyebolt with Nord-Lock washers
• Eyebolt, Nut and Nord-Lock, Cylinder Anchor
• Eyebolt replacement with Nord-Lock washers
• 1 inch cylinder anchor eyebolt assembly
• MX000077 - related StrongArm cylinder assembly; not the same part
• MX000312 - related cylinder pin; not the same part
• MX001100 - related crankshaft assembly; not the same part

Related Parts and Accessories

The correct related parts depend on the installed StrongArm model, cylinder mounting arrangement, and cause of the original hardware issue. Inspect the full cylinder anchor and arm-drive area before ordering only this eyebolt assembly.

• MX000077 cylinder assembly - related hydraulic cylinder, not the eyebolt hardware.
• MX000312 cylinder pin - related linkage hardware, not the cylinder anchor eyebolt.
• MX001100 crankshaft with bearing, zerk and keys - related arm-drive part, not the cylinder anchor hardware.
• MX000306 4-bolt crankshaft bearing - related bearing support part, not the eyebolt hardware.
• Hydraulic hose kits and fittings - inspect for leaks, restrictions, and damage during cylinder anchor service.
• Yoke, counterweight, and arm mounting hardware - inspect if the arm is binding, sagging, or out of balance.

Technician Note

Before replacing MX002467, inspect the cylinder anchor area carefully. Look for bent or stretched hardware, damaged threads, loose nuts, missing Nord-Lock washers, wallowed mounting holes, misaligned cylinder hardware, worn cylinder pins, damaged cylinder rod ends, and signs of arm impact or overload.

Do not replace the Nord-Lock washer set with standard washers unless HySecurity documentation confirms the substitution. The locking washer arrangement is part of the specified cylinder anchor hardware and helps maintain clamping under vibration and load.

Before Ordering, Confirm

• The required part number is MX002467.
• The operator is a HySecurity StrongArm model where the parts diagram lists MX002467.
• The StrongArm unit was manufactured after 3/25/2011, or the current parts diagram confirms MX002467 for the installed unit.
• The repair requires the cylinder anchor eyebolt, nuts and Nord-Lock washers, not the cylinder, cylinder pin, crankshaft, hose kit, or arm hardware.
• The cylinder anchor mount and surrounding bracket hardware are not bent, cracked, stripped, or wallowed out.
• The hydraulic cylinder, pins, rod end, hoses, fittings, crankshaft hardware, and arm balance have been inspected.
• The package includes the expected eyebolt, 2 nuts and 2 Nord-Lock washers.
• The operator has not been modified with non-standard cylinder anchor hardware.

Installation and Service Notes

• Secure the barrier arm before servicing cylinder anchor hardware.
• Do not work under an unsupported arm or counterweight-loaded arm assembly.
• Disconnect and secure operator power before working near moving mechanical parts.
• Relieve hydraulic load according to the manufacturer's service procedure before adjusting cylinder anchor hardware.
• Use the correct eyebolt, nuts and Nord-Lock washers specified for the cylinder anchor.
• Do not substitute generic hardware or omit locking washers from the assembly.
• After service, verify smooth arm travel, correct cylinder alignment, secure hardware, proper limit operation, and all required safety devices.

Professional Advisory

StrongArm cylinder anchor repairs should be handled by a qualified gate technician when the repair involves hydraulic pressure, heavy barrier arms, counterweights, cylinder alignment, anchor adjustment, damaged threads, arm balance, or unknown prior modifications. Do not bypass limit controls, stop circuits, kill switches, hydraulic protections, controller protections, access control safety inputs, or any required safety devices to keep the operator running.

Product Questions & Answers

What is HySecurity MX002467?

HySecurity MX002467 is an eyebolt, nut and Nord-Lock washer assembly used as cylinder anchor hardware for select HySecurity StrongArm barrier gate operators.

What operators use MX002467?

HySecurity parts documentation lists MX002467 for StrongArm models manufactured after 3/25/2011. Use it only where the operator parts diagram confirms this cylinder anchor hardware.

What is included with MX002467?

Current listings commonly describe MX002467 as including the eyebolt, 2 nuts and 2 Nord-Lock washers. Package contents should still be verified before ordering.

Is MX002467 the hydraulic cylinder?

No. MX002467 is the cylinder anchor eyebolt hardware. The hydraulic cylinder assembly is a separate part and should be verified by the operator parts diagram.

Can I use a generic eyebolt instead?

No, not unless HySecurity documentation confirms the exact replacement. This part uses specified cylinder anchor hardware with Nord-Lock washers, and generic hardware may not provide the correct fit or locking performance.

Why does the manufacture date matter for MX002467?

HySecurity parts documentation lists MX002467 for StrongArm models manufactured after 3/25/2011. Earlier units may use different cylinder anchor hardware, so the serial number and parts diagram should be checked before ordering.

What should be checked before replacing this cylinder anchor eyebolt?

Inspect the cylinder anchor mount, threads, nuts, Nord-Lock washers, hydraulic cylinder, cylinder pins, rod end, hoses, crankshaft hardware, and arm balance before replacing only the eyebolt assembly.