The AES EL00IG-RAD-PCB is a replacement PCB / control board for select AES EL00IG-RAD In-Ground radar e-Loop vehicle detection applications. It is used when the internal board in a compatible EL00IG-RAD commercial in-ground radar loop has failed, been damaged, or is no longer communicating or detecting properly.
This part is intended for board-level service work on the EL00IG-RAD in-ground e-Loop family. It replaces the internal PCB only and does not replace the complete loop housing, shell, battery, receiver, transceiver, magnet, mounting materials, wiring, or gate operator control connection.
The EL00IG-RAD-PCB should be ordered by exact part number and installed e-Loop model. Do not choose this board by appearance alone, because AES offers several EL00-series e-Loop models and related boards that may look similar but are tied to different housings, detection methods, mounting styles, battery formats, and service parts.
The EL00IG-RAD-PCB is the replacement control board used inside compatible AES EL00IG-RAD in-ground radar e-Loop units. In the correct system, the board works with the installed radar / magnetometer detection hardware, battery, wireless communication, calibration, and paired receiver or transceiver to help detect vehicles and send the proper signal to the gate control system.
This board does not operate a gate by itself. Vehicle detection still depends on the complete EL00IG-RAD sensor assembly, battery condition, receiver pairing, wireless range, in-ground installation position, radar settings, calibration, and correct wiring into the gate operator or access control input.
Use the AES EL00IG-RAD-PCB only where the installed product, AES documentation, original board marking, or supplier cross-reference confirms EL00IG-RAD in-ground PCB compatibility. Compatibility depends on the exact EL00IG-RAD model, board generation, connector layout, detection hardware, and system configuration.
Do not assume all AES EL00-series PCBs are the same. The EL00IG-RAD-PCB is for compatible EL00IG-RAD in-ground radar applications only. AES also has related e-Loop products for commercial surface-mount, light industrial, mini, and post-mount systems, and those parts are not automatically interchangeable.
If the installed unit is EL00C, EL00LI, EL00M, EL00PM, or a non-radar EL00IG version, verify the correct PCB before ordering. A board that appears similar may not match the same detection style, firmware, connector layout, battery configuration, shell design, in-ground housing, or calibration requirements.
| Feature / Specification | Details |
|---|---|
| Manufacturer | AES / AES Global |
| Part Number | EL00IG-RAD-PCB |
| Product Type | Replacement PCB / control board |
| Common Application | AES EL00IG-RAD In-Ground Commercial Radar Loop service and board replacement |
| Associated Model Family | EL00IG-RAD in-ground radar e-Loop family; verify exact installed model before ordering |
| Series Reference | EL00 |
| Associated Installation Style | In-ground e-Loop application, where confirmed by the installed EL00IG-RAD unit |
| Associated Detection Type | Radar / magnetometer wireless vehicle detection system, where supported by the installed unit |
| Board-Level Repair Item | Use only when the original board layout, connector style, and parts diagram match |
| Included Components | PCB / control board only unless the product listing or package states otherwise |
| Not Included | Complete e-Loop unit, shell assembly, battery, magnet, receiver, transceiver, wiring, gate operator, mounting hardware, mastic, or complete vehicle detection kit unless specifically stated |
For EL00IG-RAD repairs, replace the PCB only after confirming the fault is actually board-related. An in-ground radar e-Loop that does not detect, pair, transmit, or activate the gate can also have a weak battery, incorrect receiver pairing, radio interference, poor in-ground placement, standing water, damaged housing, calibration issues, radar setting issues, receiver problems, or gate operator input problems.
Inspect the shell for cracks, moisture entry, corrosion, damaged battery contacts, loose wiring, and signs of previous service before installing a new board. If water has reached the electronics, a shell repair, seal repair, battery replacement, or complete loop replacement may also be needed.
A qualified gate technician should service the system if the EL00IG-RAD unit is not detecting vehicles reliably, the receiver is not responding, the gate activates unexpectedly, the in-ground housing has water damage, or the operator input behavior is unknown. This PCB should only be used for the intended EL00IG-RAD in-ground board repair and should not be used to bypass gate safety or access control protections.
The AES EL00IG-RAD-PCB is used as a replacement PCB / control board for select AES EL00IG-RAD In-Ground radar e-Loop vehicle detection units.
No. EL00IG-RAD-PCB is the PCB / control board only. It does not include the complete e-Loop unit, shell, battery, receiver, transceiver, magnet, mounting hardware, or gate operator controls.
No. EL00IG-RAD is the complete in-ground radar loop reference, while EL00IG-RAD-PCB is the replacement PCB for compatible EL00IG-RAD units.
No. EL00IG-RAD-PCB is the control board, while EL00IG-SH is the shell assembly / replacement housing for compatible EL00IG in-ground units.
It may help if the original PCB has failed, but detection problems can also be caused by a weak battery, receiver pairing, radio range, water intrusion, damaged housing, incorrect in-ground placement, calibration, radar settings, or gate operator input issues.
Do not assume it fits other AES e-Loop models. EL00IG-RAD-PCB should only be used where the installed unit, board marking, or AES documentation confirms EL00IG-RAD in-ground compatibility.
Confirm the exact EL00IG-RAD-PCB part number, installed EL00IG-RAD model, board layout, connector style, battery condition, receiver pairing, shell condition, package contents, and whether the problem is truly PCB-related.