AES EL00LI-RAD-PCB, PCB FOR EL00LI, Light Industrial
The AES EL00LI-RAD-PCB is a replacement PCB / control board for select AES EL00LI Light Industrial radar e-Loop vehicle detection applications. It is used when the internal board in a compatible EL00LI radar loop has failed, been damaged, or is no longer communicating or detecting properly.
This part is intended for board-level service work on the EL00LI light industrial e-Loop family. It replaces the internal PCB only and does not replace the complete loop housing, shell, batteries, receiver, transceiver, magnet, mounting hardware, wiring, or gate operator control connection.
The EL00LI-RAD-PCB should be ordered by exact part number and installed e-Loop model. Do not choose this board by appearance alone, because AES offers several EL00-series e-Loop models and related boards that may look similar but are tied to different housings, detection methods, mounting styles, and service parts.
What This PCB Does
The EL00LI-RAD-PCB is the replacement control board used inside compatible AES EL00LI Light Industrial radar e-Loop units. In the correct system, the board works with the installed detection hardware, batteries, wireless communication, calibration, and paired receiver or transceiver to help detect vehicles and send the proper signal to the gate control system.
This board does not operate a gate by itself. Vehicle detection still depends on the complete EL00LI sensor assembly, battery condition, receiver pairing, wireless range, mounting position, calibration, and correct wiring into the gate operator or access control input.
Compatible With
Use the AES EL00LI-RAD-PCB only where the installed product, AES documentation, original board marking, or supplier cross-reference confirms EL00LI light industrial PCB compatibility. Compatibility depends on the exact EL00LI model, board generation, connector layout, detection hardware, and system configuration.
- Select AES EL00LI Light Industrial e-Loop applications where EL00LI-RAD-PCB is listed as the replacement PCB
- Select AES EL00LI-RAD light industrial radar loop units where the board layout and parts diagram match
- Repairs where the original board is marked, listed, or cross-referenced as EL00LI-RAD-PCB
- Service work where the shell, batteries, wiring, receiver pairing, and mounting position are still usable
- Applications where the connected receiver or transceiver, gate operator input, and radio range have been confirmed operational
- Repairs where the issue has been traced to the PCB rather than the battery, shell, receiver, antenna/radio path, calibration, or gate operator input
Important Compatibility Warning
Do not assume all AES EL00-series PCBs are the same. The EL00LI-RAD-PCB is for compatible EL00LI light industrial applications only. AES also has related e-Loop products for commercial surface-mount, in-ground, mini, and post-mount systems, and those parts are not automatically interchangeable.
If the installed unit is EL00C, EL00IG, EL00M, EL00PM, or another AES e-Loop model, verify the correct PCB before ordering. A board that appears similar may not match the same detection style, firmware, connector layout, battery configuration, shell design, or mounting position.
Similar AES e-Loop Parts That Are Not Automatically Interchangeable
- AES EL00LI-RAD-PCB: Replacement PCB / control board for select EL00LI Light Industrial radar e-Loop applications; this is the part described on this page.
- AES EL00LI-SH: Shell assembly / housing for EL00LI applications; not the same as the PCB.
- AES EL00LI-RAD: Complete light industrial radar loop reference where offered; not the same as the PCB-only replacement.
- AES EL00PM-RAD-PCB: Related PCB for EL00PM Post Mount applications; not automatically interchangeable with EL00LI-RAD-PCB.
- AES EL00IG-RAD-PCB: Related PCB for EL00IG in-ground radar applications; not the same light industrial board.
- AES EL00C parts: Commercial e-Loop battery, shell, magnet, and spares items are different service parts and should not be substituted for this PCB.
- AES receivers / transceivers: Receiver or transceiver faults can look like loop PCB failure but require a different repair.
Not Intended For
- Use as a complete AES e-Loop vehicle detection system by itself
- Replacement for the complete EL00LI radar loop unless the parts diagram calls for PCB-only service
- Replacement for the EL00LI shell, batteries, receiver, transceiver, magnet, or mounting hardware
- Replacement for EL00C, EL00IG, EL00M, EL00PM, or other AES e-Loop boards unless AES documentation confirms compatibility
- Repairing weak radio range, incorrect receiver pairing, failed batteries, damaged shell, water intrusion, or gate operator input problems without proper diagnosis
- Bypassing monitored gate safety inputs, photo eyes, safety edges, access control wiring, or required entrapment protection
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | AES / AES Global |
| Part Number | EL00LI-RAD-PCB |
| Product Type | Replacement PCB / control board |
| Common Application | AES EL00LI Light Industrial radar e-Loop service and board replacement |
| Associated Model Family | EL00LI / EL00LI-RAD light industrial e-Loop family; verify exact installed model before ordering |
| Series Reference | EL00 |
| Associated Detection Type | Light industrial radar / wireless e-Loop detection system, where supported by the installed unit |
| Board-Level Repair Item | Use only when the original board layout, connector style, and parts diagram match |
| Included Components | PCB / control board only unless the product listing or package states otherwise |
| Not Included | Complete e-Loop unit, shell assembly, batteries, magnet, receiver, transceiver, wiring, gate operator, mounting hardware, or complete vehicle detection kit unless specifically stated |
Also Known As / Related Part Numbers
- AES EL00LI-RAD-PCB
- EL00LI-RAD-PCB
- AES Global EL00LI-RAD-PCB
- Nice AES EL00LI-RAD-PCB
- AES PCB for EL00LI Light Industrial
- AES Control Board for EL00LI Light Industrial
- AES EL00LI Light Industrial PCB
- AES EL00LI Radar PCB
- AES EL00LI-RAD Replacement Board
- AES Light Industrial e-Loop PCB
- AES Light Industrial Radar Loop Control Board
- AES-EL00LI-RAD-PCB
- EL00LIRADPCB, possible search variation only; verify exact part number as EL00LI-RAD-PCB
- HYS-EL00LI-RAD-PCB, related distributor-style SKU format only; verify seller SKU before ordering
- EL00LI-SH, related shell assembly; not the same as the PCB
- EL00PM-RAD-PCB, related post-mount PCB; not the same as EL00LI-RAD-PCB
- EL00IG-RAD-PCB, related in-ground PCB; not the same as EL00LI-RAD-PCB
Related Parts and Accessories
- AES EL00LI-SH, shell assembly for EL00LI applications; not a PCB
- AES EL00PM-RAD-PCB, PCB for EL00PM post-mount applications; not the same board
- AES EL00IG-RAD-PCB, PCB for EL00IG in-ground radar applications; not the same board
- AES EL00C-SH, commercial e-Loop shell assembly; not the same as this PCB
- AES EL00IG-SH, in-ground e-Loop shell assembly; not the same as this PCB
- AES EL00PM-SH, post-mount shell assembly; not the same as this PCB
- AES e-Loop receiver or transceiver components, where required by the installed vehicle detection system
- AES e-Loop batteries, magnets, and service tools, where specified by the installed model
Technician Note
For EL00LI repairs, replace the PCB only after confirming the fault is actually board-related. A light industrial e-Loop that does not detect, pair, transmit, or activate the gate can also have weak batteries, incorrect pairing, radio interference, poor mounting position, water intrusion, damaged housing, receiver issues, or gate operator input problems.
Inspect the shell for cracks, moisture entry, corrosion, damaged battery contacts, loose wiring, and signs of previous service before installing a new board. If water has reached the electronics, a shell repair, seal repair, or complete loop replacement may also be needed.
Before Ordering, Confirm
- The required part number is EL00LI-RAD-PCB.
- The installed unit is an AES EL00LI / EL00LI-RAD light industrial e-Loop.
- The repair requires the PCB / control board only.
- The shell, batteries, mounting position, receiver or transceiver, and gate operator input have been checked.
- The board layout, connector style, mounting points, and battery connections match the original board.
- The part is not being confused with EL00LI-SH, EL00PM-RAD-PCB, EL00IG-RAD-PCB, or a complete e-Loop unit.
- The package contents are confirmed, especially whether any screws, battery contacts, gasket, wiring, labels, or service hardware are included.
- The problem is not caused by receiver pairing, dead batteries, weak radio range, incorrect calibration, water intrusion, or gate operator input wiring.
Installation and Service Notes
- Follow AES service instructions for the installed EL00LI light industrial e-Loop.
- Power down or disconnect the unit as directed before removing the PCB.
- Document battery orientation, connector location, board position, and any wiring before removing the original board.
- Use proper static-control handling when working with circuit boards and wireless detection electronics.
- Do not force connectors, battery terminals, board mounts, or housing parts into place.
- Inspect for moisture, corrosion, cracked shell parts, loose fasteners, damaged battery leads, and worn sealing surfaces before reassembly.
- After replacement, test pairing, detection response, receiver/transceiver operation, gate activation input, calibration, and normal gate operation.
- Do not bypass monitored gate safety inputs, photo eyes, safety edges, access control wiring, or required entrapment protection during testing.
Professional Advisory
A qualified gate technician should service the system if the EL00LI unit is not detecting vehicles reliably, the receiver is not responding, the gate activates unexpectedly, the housing has water damage, or the operator input behavior is unknown. This PCB should only be used for the intended EL00LI light industrial board repair and should not be used to bypass gate safety or access control protections.
Product Questions & Answers
What is the AES EL00LI-RAD-PCB used for?
The AES EL00LI-RAD-PCB is used as a replacement PCB / control board for select AES EL00LI Light Industrial radar e-Loop vehicle detection units.
Does EL00LI-RAD-PCB include the complete light industrial e-Loop?
No. EL00LI-RAD-PCB is the PCB / control board only. It does not include the complete e-Loop unit, shell, batteries, receiver, transceiver, magnet, mounting hardware, or gate operator controls.
Is EL00LI-RAD-PCB the same as EL00LI-SH?
No. EL00LI-RAD-PCB is the control board, while EL00LI-SH is the shell assembly / replacement housing for compatible EL00LI units.
Is EL00LI-RAD-PCB the same as EL00PM-RAD-PCB?
No. EL00LI-RAD-PCB is for compatible EL00LI light industrial applications, while EL00PM-RAD-PCB is for EL00PM post-mount applications. They should not be treated as automatic replacements.
Can this PCB fix an EL00LI unit that is not detecting vehicles?
It may help if the original PCB has failed, but detection problems can also be caused by weak batteries, receiver pairing, radio range, water intrusion, damaged housing, incorrect mounting position, calibration, or gate operator input issues.
Will this PCB fit other AES e-Loop models?
Do not assume it fits other AES e-Loop models. EL00LI-RAD-PCB should only be used where the installed unit, board marking, or AES documentation confirms EL00LI light industrial compatibility.
What should I check before ordering AES EL00LI-RAD-PCB?
Confirm the exact EL00LI-RAD-PCB part number, installed EL00LI model, board layout, connector style, battery condition, receiver pairing, shell condition, package contents, and whether the problem is truly PCB-related.
