AES EL00IG-RAD-PCB, PCB FOR EL00IG-RAD, In-Ground
The AES EL00IG-RAD-PCB is a replacement PCB / control board for select AES EL00IG-RAD In-Ground radar e-Loop vehicle detection applications. It is used when the internal board in a compatible EL00IG-RAD commercial in-ground radar loop has failed, been damaged, or is no longer communicating or detecting properly.
This part is intended for board-level service work on the EL00IG-RAD in-ground e-Loop family. It replaces the internal PCB only and does not replace the complete loop housing, shell, battery, receiver, transceiver, magnet, mounting materials, wiring, or gate operator control connection.
The EL00IG-RAD-PCB should be ordered by exact part number and installed e-Loop model. Do not choose this board by appearance alone, because AES offers several EL00-series e-Loop models and related boards that may look similar but are tied to different housings, detection methods, mounting styles, battery formats, and service parts.
What This PCB Does
The EL00IG-RAD-PCB is the replacement control board used inside compatible AES EL00IG-RAD in-ground radar e-Loop units. In the correct system, the board works with the installed radar / magnetometer detection hardware, battery, wireless communication, calibration, and paired receiver or transceiver to help detect vehicles and send the proper signal to the gate control system.
This board does not operate a gate by itself. Vehicle detection still depends on the complete EL00IG-RAD sensor assembly, battery condition, receiver pairing, wireless range, in-ground installation position, radar settings, calibration, and correct wiring into the gate operator or access control input.
Compatible With
Use the AES EL00IG-RAD-PCB only where the installed product, AES documentation, original board marking, or supplier cross-reference confirms EL00IG-RAD in-ground PCB compatibility. Compatibility depends on the exact EL00IG-RAD model, board generation, connector layout, detection hardware, and system configuration.
- Select AES EL00IG-RAD In-Ground Commercial Radar Loop applications where EL00IG-RAD-PCB is listed as the replacement PCB
- Select AES EL00IG-RAD in-ground radar / magnetometer loop units where the board layout and parts diagram match
- Repairs where the original board is marked, listed, or cross-referenced as EL00IG-RAD-PCB
- Service work where the shell, battery, in-ground installation, receiver pairing, and mounting location are still usable
- Applications where the connected receiver or transceiver, gate operator input, and radio range have been confirmed operational
- Repairs where the issue has been traced to the PCB rather than the battery, shell, receiver, radio path, radar settings, calibration, or gate operator input
Important Compatibility Warning
Do not assume all AES EL00-series PCBs are the same. The EL00IG-RAD-PCB is for compatible EL00IG-RAD in-ground radar applications only. AES also has related e-Loop products for commercial surface-mount, light industrial, mini, and post-mount systems, and those parts are not automatically interchangeable.
If the installed unit is EL00C, EL00LI, EL00M, EL00PM, or a non-radar EL00IG version, verify the correct PCB before ordering. A board that appears similar may not match the same detection style, firmware, connector layout, battery configuration, shell design, in-ground housing, or calibration requirements.
Similar AES e-Loop Parts That Are Not Automatically Interchangeable
- AES EL00IG-RAD-PCB: Replacement PCB / control board for select EL00IG-RAD in-ground radar e-Loop applications; this is the part described on this page.
- AES EL00IG-RAD: Complete in-ground commercial radar loop reference; not the same as the PCB-only replacement.
- AES EL00IG-SH: Shell assembly / housing for EL00IG in-ground applications; not the same as the PCB.
- AES EL00IG-B: Replacement 3.6V D battery for compatible in-ground e-Loop applications; not a control board.
- AES EL00IG-SPARES-KIT: 3mm hex key and magnet service kit; not the same as the PCB.
- AES EL00PM-RAD-PCB: Related PCB for EL00PM Post Mount applications; not automatically interchangeable with EL00IG-RAD-PCB.
- AES EL00LI-RAD-PCB: Related PCB for EL00LI Light Industrial applications; not the same in-ground board.
- AES EL00M-PCB: Related PCB for EL00M Mini applications; not the same as EL00IG-RAD-PCB.
- AES receivers / transceivers: Receiver or transceiver faults can look like loop PCB failure but require a different repair.
Not Intended For
- Use as a complete AES e-Loop vehicle detection system by itself
- Replacement for the complete EL00IG-RAD loop unless the parts diagram calls for PCB-only service
- Replacement for the EL00IG shell, battery, receiver, transceiver, magnet, or mounting hardware
- Replacement for EL00C, EL00LI, EL00M, EL00PM, or other AES e-Loop boards unless AES documentation confirms compatibility
- Repairing weak radio range, incorrect receiver pairing, failed batteries, damaged shell, water intrusion, poor in-ground mounting, or gate operator input problems without proper diagnosis
- Bypassing monitored gate safety inputs, photo eyes, safety edges, access control wiring, or required entrapment protection
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | AES / AES Global |
| Part Number | EL00IG-RAD-PCB |
| Product Type | Replacement PCB / control board |
| Common Application | AES EL00IG-RAD In-Ground Commercial Radar Loop service and board replacement |
| Associated Model Family | EL00IG-RAD in-ground radar e-Loop family; verify exact installed model before ordering |
| Series Reference | EL00 |
| Associated Installation Style | In-ground e-Loop application, where confirmed by the installed EL00IG-RAD unit |
| Associated Detection Type | Radar / magnetometer wireless vehicle detection system, where supported by the installed unit |
| Board-Level Repair Item | Use only when the original board layout, connector style, and parts diagram match |
| Included Components | PCB / control board only unless the product listing or package states otherwise |
| Not Included | Complete e-Loop unit, shell assembly, battery, magnet, receiver, transceiver, wiring, gate operator, mounting hardware, mastic, or complete vehicle detection kit unless specifically stated |
Also Known As / Related Part Numbers
Related Parts and Accessories
- AES EL00IG-RAD, complete in-ground commercial radar loop reference; verify if the repair needs the full loop instead of the PCB
- AES EL00IG-SH, shell assembly for EL00IG in-ground e-Loop applications; not a PCB
- AES EL00IG-B, 3.6V D battery reference for compatible in-ground e-Loop applications; not a PCB
- AES EL00IG-SPARES-KIT, 3mm hex key and magnet kit for EL00IG service work; not a PCB
- AES EL00PM-RAD-PCB, PCB for EL00PM post-mount applications; not the same board
- AES EL00LI-RAD-PCB, PCB for EL00LI light industrial applications; not the same board
- AES EL00M-PCB, PCB for EL00M Mini applications; not the same board
- AES e-Loop receiver or transceiver components, where required by the installed vehicle detection system
- AES e-Loop batteries, magnets, and service tools, where specified by the installed model
Technician Note
For EL00IG-RAD repairs, replace the PCB only after confirming the fault is actually board-related. An in-ground radar e-Loop that does not detect, pair, transmit, or activate the gate can also have a weak battery, incorrect receiver pairing, radio interference, poor in-ground placement, standing water, damaged housing, calibration issues, radar setting issues, receiver problems, or gate operator input problems.
Inspect the shell for cracks, moisture entry, corrosion, damaged battery contacts, loose wiring, and signs of previous service before installing a new board. If water has reached the electronics, a shell repair, seal repair, battery replacement, or complete loop replacement may also be needed.
Before Ordering, Confirm
- The required part number is EL00IG-RAD-PCB.
- The installed unit is an AES EL00IG-RAD In-Ground Commercial Radar Loop.
- The repair requires the PCB / control board only.
- The shell, battery, in-ground mounting location, receiver or transceiver, and gate operator input have been checked.
- The board layout, connector style, mounting points, and battery connections match the original board.
- The part is not being confused with EL00IG-SH, EL00IG-B, EL00IG-SPARES-KIT, EL00IG-RAD complete loop, EL00PM-RAD-PCB, or EL00LI-RAD-PCB.
- The package contents are confirmed, especially whether any screws, battery contacts, gasket, wiring, labels, or service hardware are included.
- The problem is not caused by receiver pairing, dead battery, weak radio range, incorrect calibration, radar settings, water intrusion, or gate operator input wiring.
Installation and Service Notes
- Follow AES service instructions for the installed EL00IG-RAD in-ground e-Loop.
- Power down or disconnect the unit as directed before removing the PCB.
- Document battery orientation, connector location, board position, and any wiring before removing the original board.
- Use proper static-control handling when working with circuit boards and wireless detection electronics.
- Do not force connectors, battery terminals, board mounts, shell parts, or in-ground housing components into place.
- Inspect for moisture, corrosion, cracked shell parts, loose fasteners, damaged battery leads, and worn sealing surfaces before reassembly.
- After replacement, test pairing, detection response, receiver/transceiver operation, gate activation input, calibration, radar response, and normal gate operation.
- Do not bypass monitored gate safety inputs, photo eyes, safety edges, access control wiring, or required entrapment protection during testing.
Professional Advisory
A qualified gate technician should service the system if the EL00IG-RAD unit is not detecting vehicles reliably, the receiver is not responding, the gate activates unexpectedly, the in-ground housing has water damage, or the operator input behavior is unknown. This PCB should only be used for the intended EL00IG-RAD in-ground board repair and should not be used to bypass gate safety or access control protections.
Product Questions & Answers
The AES EL00IG-RAD-PCB is used as a replacement PCB / control board for select AES EL00IG-RAD In-Ground radar e-Loop vehicle detection units.
Does EL00IG-RAD-PCB include the complete in-ground e-Loop?
No. EL00IG-RAD-PCB is the PCB / control board only. It does not include the complete e-Loop unit, shell, battery, receiver, transceiver, magnet, mounting hardware, or gate operator controls.
No. EL00IG-RAD is the complete in-ground radar loop reference, while EL00IG-RAD-PCB is the replacement PCB for compatible EL00IG-RAD units.
No. EL00IG-RAD-PCB is the control board, while EL00IG-SH is the shell assembly / replacement housing for compatible EL00IG in-ground units.
Can this PCB fix an EL00IG-RAD unit that is not detecting vehicles?
It may help if the original PCB has failed, but detection problems can also be caused by a weak battery, receiver pairing, radio range, water intrusion, damaged housing, incorrect in-ground placement, calibration, radar settings, or gate operator input issues.
Will this PCB fit other AES e-Loop models?
Do not assume it fits other AES e-Loop models. EL00IG-RAD-PCB should only be used where the installed unit, board marking, or AES documentation confirms EL00IG-RAD in-ground compatibility.
What should I check before ordering AES EL00IG-RAD-PCB?
Confirm the exact EL00IG-RAD-PCB part number, installed EL00IG-RAD model, board layout, connector style, battery condition, receiver pairing, shell condition, package contents, and whether the problem is truly PCB-related.
