HySecurity MX001162, LONG DISTANCE MODULE
The HySecurity MX001162 long distance module is a control-circuit interface used to help isolate open-close-stop command wiring from noise, induced voltage, and lightning-related interference on long wire runs. HySecurity wiring references identify MX001162 as the long-distance interface for StrongArm, SlideDriver, SwingRiser, and HydraLift, and accessory listings describe it as an open/close/stop noise and lightning isolator. This part is typically considered when a remote control station, guard shack, pedestal, or dry-contact command device is located far from the operator and nuisance commands or unreliable inputs are suspected. It should be installed as part of a proper low-voltage control wiring design, not as a substitute for correct grounding, surge protection, shielded cable where needed, or controller input troubleshooting.
Features and Specifications
| Manufacturer | HySecurity / Nice HySecurity |
|---|
| Product Type | Long distance module / noise isolator |
|---|
| Part Number | MX001162 |
|---|
| Application | Open-close-stop control circuit isolation |
|---|
| Signal Type | Low-voltage command wiring interface |
|---|
| Common Use | Long wire runs to remote control stations |
|---|
| Compatible Operator Type | Select HySecurity hydraulic, Smart DC, Smart Touch, and commercial/industrial operators |
|---|
| Notes | Install according to HySecurity wiring diagram |
|---|
Compatible With
- HySecurity StrongArm applications where MX001162 is specified
- HySecurity SlideDriver applications where long-distance open-close-stop wiring is used
- HySecurity SwingRiser applications where the wiring diagram calls for the module
- HySecurity HydraLift and HydraSwing applications where supported
- HySecurity SlideSmart DC and SwingSmart DC applications where a long-distance interface is required
- HySecurity StrongArmPark DC, SlideSmart HD, WedgeSmart, HydraWedge SM50, and StrongArm M30/M50 applications when listed by accessory documentation
- Remote push-button, key switch, or control station wiring runs that need open-close-stop isolation
- Not a monitored entrapment protection device or universal surge protector
Also Known As / Related Part Numbers
- MX001162
- HYS-MX001162
- Nice HySecurity MX001162
- Long Distance Module
- Long Distance Interface
- Noise Isolator
- Open Close Stop noise isolator
- Lightning isolator
- Control wire isolator
- Long distance command module
Technician Note
Use the HySecurity long-distance interface wiring diagram and confirm the controller input type before connecting field wiring. Do not use the module to mask a grounding or wiring fault.
Before Ordering Checklist
- Confirm the operator controller supports MX001162
- Verify the issue involves open-close-stop control wiring, not radio or safety input wiring
- Check cable route, grounding, conduit, and surge exposure
- Confirm the command device uses the correct dry-contact arrangement
- Use the HySecurity wiring diagram for terminal placement
Professional Advisory
Long control wiring runs can collect electrical noise and surge energy. If the site has recurring lightning damage or nuisance inputs, have the complete grounding and surge-protection layout reviewed.
Important Ordering Warnings
- Not a replacement for safety devices
- Not a universal surge protector for all operator circuits
- Do not connect high voltage to low-voltage control inputs
Product Questions and Answers
What does MX001162 do?
MX001162 helps isolate long open-close-stop control wiring from noise and lightning-related interference.
Is MX001162 a receiver?
No. It is a long-distance control wiring interface/noise isolator, not a radio receiver.
Which operators can use it?
It is commonly associated with select HySecurity StrongArm, SlideDriver, SwingRiser, HydraLift, HydraSwing, Smart DC, and related operator families when the wiring diagram calls for it.
Will it fix every nuisance opening problem?
No. Nuisance operation can also be caused by wiring faults, shorted devices, water intrusion, radio issues, or controller problems.
Can it replace safety edge or photo eye protection?
No. It is not an entrapment protection device and must not be used as a safety-device substitute.
