HySecurity MX001753, HARNESS, LIMIT SWITCHES, SM
The HySecurity MX001753 is a limit switch wiring harness for select HySecurity SwingSmart DC swing gate operators. This harness connects the limit switch circuit to the operator wiring so the controller receives proper open and close limit information. It is typically considered when the operator shows intermittent limit recognition, damaged wire insulation, broken connectors, switch signal errors, or physical harness damage near the moving arm or limit hardware. Limit wiring is important to safe and predictable gate travel; a poor connection can cause nuisance faults or incorrect stopping behavior even if the switch itself is still good. MX001753 should be matched to the SwingSmart DC model and parts diagram before ordering.
This is a service replacement part, so correct fitment matters more than the product name alone. HySecurity has used different assemblies across hydraulic slide operators, Smart DC operators, barrier operators, swing operators, and high-security crash products. Always compare the original part number, operator model, voltage or hydraulic configuration when applicable, connector or fitting style, and the factory parts diagram before ordering.
Compatible With
This part may be used with the following HySecurity applications when the installed operator and parts diagram confirm the match:
- HySecurity SwingSmart DC swing gate openers where MX001753 is specified
- SwingSmart DC limit switch wiring service locations
- select SwingSmart DC operator generations using the matching harness, connector, and routing. Do not substitute for StrongArm MX001715 or unrelated SlideSmart/AC power harnesses without parts-diagram confirmation.
Compatibility should be verified before installation. Similar HySecurity parts may look close but differ by connector, hose length, switch geometry, voltage rating, gear size, lock cylinder, or operator generation.
Features & Specifications
| Manufacturer | HySecurity / Nice HySecurity |
|---|
| Product Type | Limit switch wiring harness |
|---|
| Part Number | MX001753 |
|---|
| Application | SwingSmart DC limit switch wiring |
|---|
| Compatible Operator Type | HySecurity SwingSmart DC references |
|---|
| Included Components | Harness only unless otherwise stated |
|---|
| Notes | Verify connector, routing, and operator generation |
|---|
Also Known As / Related Part Numbers
- MX001753
- MX001753-5128
- HYS-MX001753
- Nice HySecurity MX001753
- SwingSmart DC limit switch harness
- Harness limit switches SM
- Limit switch harness swing gate
Technician Note
Before replacing this part, inspect the surrounding assembly for the condition that caused the failure. Worn pivots, loose hardware, incorrect routing, damaged wiring, leaking hydraulic fittings, bad mating gears, or a changed lock cylinder can make the replacement part appear incorrect or cause repeat failures.
Before Ordering
- Confirm the HySecurity part number on the original part, package label, or parts diagram.
- Verify the exact operator model and generation.
- Compare connector style, hose fitting, switch arm shape, key/lock type, or mechanical dimensions as applicable.
- Check whether related hardware, seals, bushings, switches, fittings, or mating parts should be replaced at the same time.
- For electrical or hydraulic service, use a qualified gate technician if the repair involves unsafe voltage, stored energy, hydraulic pressure, or moving gate components.
Professional Advisory
Do not bypass limit switches, monitored safety devices, covers, lock hardware, or required safety circuits to keep a gate running. If the operator moves unpredictably, overtravels, leaks hydraulic oil, trips protection, or has damaged wiring, the system should be inspected and repaired before being returned to service.
Product Questions & Answers
What does the MX001753 harness connect?
It connects the limit switch wiring on select HySecurity SwingSmart DC swing gate operators.
Is MX001753 the same as MX001715?
No. MX001753 is associated with SwingSmart DC limit switch wiring, while MX001715 is commonly listed for StrongArm limit sensor switch use.
Can a harness cause limit faults?
Yes. A broken conductor, loose connector, or damaged insulation can interrupt the limit signal and cause intermittent travel problems.
Does this harness include limit switches?
This listing is for the harness unless the product details state that switches are included.
What should be checked after replacing it?
The technician should check wire routing, connector seating, limit switch operation, and open/close limit settings before returning the gate to service.
