HySecurity MX3483-10, BUMPER, T-SLOT, SAP ARM, 10'
The HySecurity MX3483-10 is a T-slot bumper for select SAP / StrongArmPark barrier arm assemblies. It mounts to the arm profile to provide a replaceable bumper surface that helps reduce contact damage and restores the proper appearance and protection of the traffic arm.
Arm bumpers are commonly replaced when the original bumper is torn, missing, weathered, pulled from the T-slot, or damaged by vehicle contact. The arm length and profile matter. MX3483-10 should be used only where the parts diagram or installed arm calls for the 10 ft version, not the longer 14 ft MX3483-14 version or a different barrier arm profile.
Compatible With
- Select HySecurity StrongArmPark DC / SAP barrier arm assemblies requiring MX3483-10.
- 10 ft T-slot SAP arm bumper applications where the installed arm profile matches.
- Commonly associated with StrongArmPark arm maintenance, arm-impact repair, and bumper replacement work.
- May be used with lighted or non-lighted arm assemblies only when the T-slot profile and length match.
- Not a universal foam pad or bumper for every HySecurity barrier arm.
- Use MX3483-14 where the operator/arm requires the 14 ft version.
Features and Specifications
| Manufacturer | HySecurity / Nice HySecurity |
|---|
| Part Number | MX3483-10 |
|---|
| Product Type | T-slot arm bumper |
|---|
| Primary Application | Replacement T-slot bumper for select StrongArmPark / SAP barrier arm assemblies |
|---|
| Compatible Operator Type | Barrier arm / StrongArmPark arm applications |
|---|
| Handing / Size / Rating | 10 ft SAP arm bumper reference; verify arm profile and length. |
|---|
| Included Components | T-slot bumper only unless hardware is listed. |
|---|
| Notes | Length/profile-specific arm bumper; do not confuse with 14 ft version MX3483-14. |
|---|
Also Known As / Related Part Numbers
- MX3483-10
- MX348310
- MX3483 10
- Bumper, T-Slot, SAP Arm, 10 ft
- T-slot SAP arm bumper 10 ft
- HySecurity StrongArmPark 10 ft arm bumper
- Related longer version: MX3483-14
Technician Note
Measure the arm and inspect the T-slot before ordering. A bumper that is too short, too long, or made for a different extrusion profile may not seat correctly in the arm.
Before Ordering
- Confirm part number MX3483-10 in the HySecurity parts diagram.
- Verify 10 ft arm requirement and T-slot profile.
- Inspect the arm extrusion for damage before installing a new bumper.
- Check for missing end caps or retaining hardware.
- Confirm arm balance and travel after repair if the arm was impacted.
Professional Advisory
Installation and service on automated gate equipment should be performed by a qualified gate technician. Do not bypass safety devices, breakaway switches, monitored edges, or photo eyes to make a gate run.
Product Questions and Answers
What is HySecurity MX3483-10 used for?
HySecurity MX3483-10 is used as a t-slot arm bumper in replacement t-slot bumper for select strongarmpark / sap barrier arm assemblies. It should be selected by the exact part number and the operator parts diagram.
Is MX3483-10 compatible with all HySecurity operators?
No. MX3483-10 should only be used with the HySecurity operator families and assemblies that list this part number or an approved related number in the parts diagram.
What should I check before ordering MX3483-10?
Check the original part number, operator model, serial number, production date when relevant, and the physical style of the old part. Also inspect nearby hardware or wiring that may have caused the failure.
Can I install MX3483-10 myself?
Mechanical parts should be installed only by someone familiar with automated gate equipment. Electrical parts and safety-related repairs should be handled by a qualified gate technician.
Are there related part numbers for MX3483-10?
Yes. See the Also Known As / Related Part Numbers section on this page. Related numbers may describe opposite-hand parts, newer or older harnesses, companion parts, or search variations and are not always direct replacements.
