AES GSM-ANT-PCB LTE Internal PCB Antenna with 100mm Cable
The AES GSM-ANT-PCB is an LTE internal PCB antenna with a 100mm cable for select AES cellular access control and intercom equipment. It is intended for applications where the installed AES system uses the internal PCB-style LTE antenna and the original antenna assembly is identified as GSM-ANT-PCB.
This is an antenna component only. It is not a cellular module, SIM card, modem board, external antenna kit, PoE device, power supply, or complete AES communication package. Match the antenna by part number, cable length, connector type, mounting location, and the installed AES documentation before ordering.
Primary Use
- Replacement internal LTE PCB antenna for select AES cellular equipment
- Used where the original antenna assembly is marked, listed, or cross-referenced as GSM-ANT-PCB
- Helps replace a damaged, disconnected, corroded, kinked, or missing internal LTE antenna assembly
- Intended for internal antenna applications using a 100mm antenna cable where specified
Compatible With
Use AES GSM-ANT-PCB only where the installed equipment, cellular module, parts diagram, or AES service documentation confirms this antenna as the correct replacement. Do not assume compatibility based only on the AES brand or LTE wording.
- Select AES LTE/cellular intercom and access control systems where GSM-ANT-PCB is listed
- Repairs where the original internal PCB antenna is marked or cross-referenced as GSM-ANT-PCB
- Applications where the antenna cable length, connector type, mounting location, and cellular module requirements match the installed equipment
- Internal LTE antenna replacements where the system documentation calls for a PCB-style internal antenna rather than an external puck antenna
Features and Specifications
| Specification | Details |
| Brand | AES / AES Global |
| Part Number | GSM-ANT-PCB |
| Product Type | Internal LTE PCB antenna |
| Cable Length | 100mm |
| Antenna Style | PCB-style internal antenna |
| Wireless Use | LTE/cellular applications where supported by the installed AES equipment |
| Connector Type | Verify against the original antenna and cellular module before ordering |
| Mounting Location | Internal mounting location where specified by AES documentation |
| Programming Required | No programming for the antenna itself; cellular service and module status may still need to be checked |
| Package Contents | Confirm before ordering; treat as the internal antenna and 100mm cable unless additional parts are specifically stated |
Important Comparison With Similar AES Antenna Parts
AES antenna parts may serve different installation needs. Match the antenna type, cable length, connector, and mounting style before ordering.
- GSM-ANT-PCB: Internal LTE PCB antenna with 100mm cable for select AES cellular equipment where specified.
- GSM-ANT-4GP-KIT: Related external LTE puck antenna kit with longer cable and bracket. This is not the same part as the internal PCB antenna.
- Cellular module or modem board: Not the same part. An antenna replacement will not correct a failed modem, inactive account, SIM issue, or board-level cellular fault.
- SIM card: Not the same part. A SIM or service/account issue can create cellular problems even when the antenna is good.
- Generic LTE antenna: Do not substitute a generic antenna unless the connector, cable length, frequency support, mounting style, and AES documentation confirm it is suitable.
Also Known As / Related Part Numbers
- GSM-ANT-PCB
- GSMANTPCB
- AES GSM-ANT-PCB
- AES Global GSM-ANT-PCB
- Nice AES GSM-ANT-PCB
- AES PCB antenna LTE internal antenna
- AES LTE internal PCB antenna
- AES internal LTE antenna with 100mm cable
- AES cellular internal antenna
- AES GSM antenna PCB
- PCB Antenna LTE Internal Antenna 100mm Cable
- GSM-ANT-4GP-KIT - related external LTE puck antenna kit, not the same internal PCB antenna
Technician Notes
- Match the replacement antenna by the GSM-ANT-PCB part number, cable length, connector type, and the installed AES cellular equipment documentation.
- Inspect the original antenna cable for sharp bends, crushed sections, pulled connectors, corrosion, moisture damage, or loose connection at the cellular module.
- Check antenna placement before replacing parts. Internal antennas can perform poorly if tucked behind metal, pinched against wiring, mounted incorrectly, or blocked by the enclosure layout.
- Cellular signal problems can also come from weak carrier coverage, inactive SIM service, poor account status, failed cellular module, water intrusion, power instability, damaged coax, or incorrect programming.
- Do not substitute the external puck antenna kit unless the installation requires that style and the AES documentation confirms compatibility.
- Do not force the antenna connector onto the board. Small RF connectors can be damaged if misaligned, pressed at an angle, or connected to the wrong port.
Before Ordering Checklist
- Confirm the exact part number is GSM-ANT-PCB.
- Confirm the installed AES equipment uses an internal LTE PCB antenna.
- Confirm the original antenna cable length is 100mm or that 100mm is specified by the parts documentation.
- Confirm the antenna connector type matches the cellular module or antenna port.
- Confirm the system does not require the external GSM-ANT-4GP-KIT puck antenna kit instead.
- Inspect the original antenna cable, connector, mounting location, cellular module, SIM/account status, and power supply condition.
- Confirm whether the listing includes only the antenna assembly or any adhesive, mounting material, clips, brackets, or related hardware.
Professional Advisory
This antenna does not require programming by itself, but AES cellular systems may involve access credentials, app setup, SIM service, cellular module configuration, relay outputs, gate operator wiring, electric locks, fire access equipment, and safety-related circuits. If the system has poor cellular service, intermittent communication, unknown prior modifications, or wiring tied into a gate operator or access control relay, have the equipment checked by a qualified gate or access control technician. Do not bypass safety devices, fire access equipment, monitored protection circuits, or operator control protections while troubleshooting.
Product Q&A
What is AES GSM-ANT-PCB used for?
AES GSM-ANT-PCB is an LTE internal PCB antenna with a 100mm cable for select AES cellular intercom and access control equipment where the installed system documentation confirms this antenna.
Is GSM-ANT-PCB an external antenna kit?
No. GSM-ANT-PCB is an internal PCB-style LTE antenna with a 100mm cable. It should not be confused with the AES GSM-ANT-4GP-KIT external puck antenna kit with longer cable and bracket.
Will this antenna improve weak cellular signal?
It may help if the original internal antenna is damaged, disconnected, corroded, or missing. Weak signal can also be caused by poor carrier coverage, metal enclosure interference, bad antenna placement, inactive SIM service, power problems, or a failed cellular module.
Does GSM-ANT-PCB include the cellular modem or SIM card?
No. GSM-ANT-PCB should be treated as the internal LTE PCB antenna and 100mm cable unless additional parts are specifically stated. It is not a modem board, SIM card, cellular service plan, or complete communication kit.
What should I verify before ordering GSM-ANT-PCB?
Verify the original part number, antenna style, 100mm cable length, connector type, mounting location, and AES system documentation. Also confirm the problem is not caused by the cellular module, SIM service, power supply, or wiring.
Can I replace this antenna with a generic LTE antenna?
Do not use a generic antenna unless the connector, cable length, LTE frequency support, mounting style, and system documentation confirm it is suitable. A similar-looking antenna may not connect correctly or perform properly.
Can I install GSM-ANT-PCB myself?
The antenna is a small internal component, but care is needed with RF connectors, antenna routing, cellular electronics, and access control wiring. If the system has communication faults, wiring changes, or gate operator connections, use a qualified technician.
