BEA 10R2E-100, R2E-100 Security Sensor
The BEA 10R2E-100 is the R2E-100 active infrared request-to-exit sensor used on secure interior access-control doors. Instead of watching a large hallway area like a general motion detector, the R2E-100 is designed to place an active infrared detection pattern near the door handle. When a person reaches for the handle from the secure side, the sensor sends a release signal to the connected locking or access-control hardware. This targeted detection is useful where cross traffic, warm air movement, or general room motion could cause unwanted door releases. Correct installation is important because request-to-exit devices are part of the egress and security design, not just a convenience accessory.
BEA’s UL Listed R2E-100 is a request-to-exit sensor with an
active infrared (AIR) detection zone focused directly on the
door handle. This allows the R2E-100 to only detect people
intending to exit through the door as they reach for the door
handle.
The AIR based R2E-100 improves accuracy of detection as
compared to passive infrared (PIR) technology including
ground based errors, PIR sensor spoofing, known PIR
vulnerabilities (hot air, background objects, cross traffic).
Standards Compliant
UL 294/ULC S319 Listed
Define Your Tilt Angle
Adjustable tilt angle from 0-10 degrees
Customizable Detection Zones
Adjustable detection range from 20-48 inches
Low Profile Mounting
Low profile sensor mounts on or above the door frame
Multiple Inputs
Three DRY auxiliary inputs; a push button or other request-to-exit device, a card reader or other request-to-enter device, and a door position switch
Technical Specifications
| Specification | Details |
|---|
| Detector Type | Focused Active Infrared |
|---|
| Supply Voltage | 12 – 24 VAC / VDC; ±10% @ 60 Hz |
|---|
| Current - Sounder OFF | 155 mA |
|---|
| Current - Sounder MAX VOLUME | 200 mA |
|---|
| Temperature (UL Install) | 32 – 120 °F (0 – 49 °C) |
|---|
| Temperature | -20 – 120 °F (-29 – 49 °C) |
|---|
| Humidity (ULC S319 Installation) | 0 – 93% non-condensing |
|---|
| Humidity (UL 294 Installation) | 0 – 85% non-condensing |
|---|
| Detection Range | 20 – 48", adjustable via potentiometer |
|---|
| Relay | 2 Form "C" contact sets; 1.3 A @ 24 VAC / 30 VDC |
|---|
| Relay Hold Time | 0.5 – 60 s, adjustable via potentiometer |
|---|
| Sounder | 85 dB max, adjustable volume |
|---|
| Indicator LEDs | Green, Red, Yellow, Orange |
|---|
| REX Input | DRY contact, NO |
|---|
| Card Reader Input | DRY contact, NC |
|---|
| Door Position Switch Input | DRY contact, NO |
|---|
| Dimensions | 6 7/10" (W) × 1 7/10" (D) × 2" (H) |
|---|
| Material | Plastic (ABS and PC) |
|---|
| Wiring Interface | JST (14-pin) with 4' cable |
|---|
| Norm Conformity | UL 294 / ULC S319 |
|---|
| FCC Compliance | FCC Part 15 B |
|---|
Compatible With
- Interior protected-premise access-control doors
- Electric lock release applications requiring request-to-exit sensing
- Employee entrances and controlled interior doors
- Door header installations focused toward the handle area
- Systems using relay input from a request-to-exit sensor when voltage and wiring match
Features & Specifications
| Manufacturer | BEA |
|---|
| Product Type | Request-to-exit active infrared sensor |
|---|
| Part Number | 10R2E-100 |
|---|
| Model | R2E-100 |
|---|
| Application | Interior access-control door egress |
|---|
| Detection Technology | Focused active infrared |
|---|
| Common Mounting | On or above the door header |
|---|
| Typical Use | Electric lock release / RTE signal |
|---|
| Notes | Match to access-control and egress requirements |
|---|
Also Known As / Related Part Numbers
- 10R2E-100
- R2E-100
- BEA R2E100
- BEA R2E-100 security sensor
- BEA active infrared request-to-exit sensor
- RTE sensor - related search term
Technician Note
A request-to-exit sensor affects both security and safe egress. Confirm the required fail-safe or fail-secure lock behavior, local code requirements, door hardware, and access-controller input before replacing or adding this device.
Before Ordering
- Confirm the opening is an interior protected-premise application.
- Verify the access controller accepts the sensor relay/output type.
- Confirm the electric lock and egress design meet code.
- Check mounting height, handle position, and detection aiming.
- Do not use this as a general motion detector or gate safety sensor.
- Test lock release, relock timing, and manual egress after installation.
Important Ordering Warnings
- Do not disable required egress devices or life-safety hardware when installing an RTE sensor.
Professional Advisory
Automatic pedestrian door sensors and wireless controls should be installed, adjusted, and tested by a qualified automatic door technician. Do not use an activation sensor as a substitute for required presence, safety, or monitored protection devices.
Product Questions & Answers
Where is the R2E-100 normally installed?
The R2E-100 is normally mounted on or above the secure-side door header so its active infrared zone is focused near the door handle.
Is the R2E-100 a request-to-exit device?
Yes. It is a request-to-exit sensor for access-control doors, designed to release an electric lock when a person intentionally reaches toward the handle.
Is this the same as a passive infrared motion detector?
No. The R2E-100 uses active infrared detection focused at the handle area and is intended to reduce unwanted releases from cross traffic.
Can this be used outdoors?
The R2E-100 is generally used for interior protected-premise applications. Check the site environment and product documentation before using it in exposed areas.
Does this replace a push button?
It may be used as a hands-free request-to-exit device in suitable systems, but the access-control and life-safety design must still meet code requirements.
