CAME 3199ZBX6110 ZBX6 120V Control Board
The CAME 3199ZBX6110 is a replacement electronic control board for select CAME BX Series sliding gate operators using a compatible ZBX6 120V / 110V board configuration. It is commonly associated with CAME BX-B 120V sliding gate operator applications and other BX Series installations where the original control board, power input, terminal layout, and operator wiring match this board family.
This board controls the main gate operator logic for compatible CAME BX sliding gate systems. In a typical installation, the control board manages open and close commands, limit switch inputs, safety device inputs, accessory power, receiver or radio command inputs, operating logic, timing functions, and the motor control sequence. When the board fails, the gate may stop responding, run intermittently, ignore commands, blow fuses, fail to process limit signals, or show issues after surge, water intrusion, insect damage, or wiring faults.
The 3199ZBX6110 should be matched by the original CAME board number and the gate operator model, not by the outside cabinet or gate brand alone. CAME has used several different boards across BX, BX-A, BX-B, BX-64, BX-68, BX-74, BX-78, BX-V, BK, BKV, and other sliding gate operator families. Many CAME boards look similar at a quick glance, but the voltage, connector layout, transformer arrangement, DIP switch logic, limit inputs, accessory terminals, and motor outputs may not be interchangeable.
The wording "LiftMaster + CAME" should be reviewed before publishing. This part appears to be a CAME replacement control board. Unless your inventory record confirms a LiftMaster-distributed CAME part or a LiftMaster/CAME co-branded replacement, the cleaner customer-facing product name should lead with CAME and the actual board number.
Because this is a line-voltage electronic board, replacement should be handled carefully. The installer should verify incoming voltage, disconnect power before service, inspect the original wiring, check all accessories for shorts, and confirm that photoeyes, safety edges, loops, receivers, keypads, exit devices, and limit wiring are not the real cause of the failure. Installing a new board into an operator with a shorted accessory or damaged field wiring can damage the replacement board.
What This Control Board Does
- Replaces a compatible CAME ZBX6 control board in select BX Series sliding gate operators
- Controls gate open, close, stop, timing, and command logic on supported systems
- Processes input from push buttons, keypads, receivers, access-control devices, and other dry-contact commands where wired correctly
- Works with compatible safety inputs such as photocells and edge inputs where supported by the operator wiring diagram
- Interfaces with compatible CAME limit switch wiring and motor control circuits
- Provides low-voltage accessory power where supported by the board and transformer configuration
- Supports board-level adjustments and DIP switch settings used on matching ZBX6 applications
Common Use Cases
- Replacing a failed CAME 3199ZBX6110 control board
- Replacing a ZBX6 120V / 110V board in a compatible CAME BX Series sliding gate operator
- Repairing a CAME BX-B 120V operator after confirmed board failure
- Replacing a control board damaged by surge, water, insects, corrosion, or wiring faults
- Restoring operation after the board has been diagnosed as the cause of command or motor-control problems
- Replacing an older board where the operator parts record specifically calls for 3199ZBX6110 or 3199-ZBX6-110
Compatible With
The CAME 3199ZBX6110 is commonly associated with select CAME BX Series sliding gate operators using the compatible ZBX6 120V / 110V board configuration. Compatibility should be confirmed by the original board number, operator model label, incoming voltage, wiring diagram, and terminal layout.
- Select CAME BX Series sliding gate operators using the ZBX6 120V / 110V board configuration
- Select CAME BX-B 120V sliding gate operator applications where the board number matches 3199ZBX6110
- Select CAME BX residential sliding gate systems where the original control panel is a matching ZBX6 version
- Select CAME systems listed with 3199-ZBX6-110 replacement board references
- Select older CAME BX installations where the original board, transformer, motor wiring, limit wiring, and safety inputs match this replacement
Important: Do not assume this board fits every CAME BX operator. Some CAME BX operators use different boards, including later or region-specific ZBX6, ZBX6N, ZBX7N, ZBX74, ZBX78, ZN7, or ZN8 style boards. Always compare the original board number and operator wiring diagram before ordering.
Commonly Associated Operator Applications
- CAME BX Series sliding gate operator applications
- CAME BX-B 120V sliding gate operator applications where the parts record confirms this board
- Residential sliding gate operators using compatible CAME ZBX6 board wiring
- Older CAME sliding gate installations where the original board is labeled or cross-referenced to 3199ZBX6110
Not Intended For
- LiftMaster gate operators unless the operator documentation specifically calls for this CAME board
- CAME BX-V operators using ZN7 or other BX-V board platforms
- CAME BKV operators using ZN8 or other BKV board platforms
- CAME BX-74 or BX-78 operators using ZBX74 / ZBX78 style boards unless confirmed by documentation
- CAME BK Series operators using ZBKN or other BK board platforms
- CAME swing gate operators such as ATI, AXO, AXI, ATS, Krono, or Frog systems using different boards
- CAME barrier gate operators such as GARD models using ZL or other barrier control boards
- Replacing a transformer, receiver, capacitor, limit switch, motor, fuse, photocell, loop detector, or safety edge
- Fixing a gate with mechanical binding, worn rollers, damaged rack, bad limit hardware, or poor ground track alignment
Important Ordering Warnings
- The product title should be reviewed because "LiftMaster + CAME" may confuse customers. This appears to be a CAME board, not a standard LiftMaster board.
- Confirm whether the board is labeled 3199ZBX6110, 3199-ZBX6-110, ZBX6 110, or another variation.
- Confirm the operator is a 120V / 110V CAME BX Series system before ordering.
- Do not replace the board until accessories, safety devices, limit switches, transformer output, fuses, and field wiring have been checked.
- Similar CAME boards may look alike but may use different voltage, programming, terminal layout, or motor output configuration.
- This is a line-voltage control board. Service should be performed by a qualified gate technician when wiring or diagnosis is not clearly understood.
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | CAME |
| Product Type | Replacement gate operator control board |
| Part Number | 3199ZBX6110 |
| Alternate Part Format | 3199-ZBX6-110 |
| Gate Openers Unlimited Part Number | CAME-3199ZBX6110 |
| Board Family | ZBX6 / ZBX-6 style control board family |
| Voltage Version | Commonly listed as 120V / 110V version for BX Series applications; verify product label before installation |
| Application | Replacement control board for select CAME BX Series sliding gate operators |
| Compatible Operator Type | Select CAME residential sliding gate operators using compatible ZBX6 board wiring |
| Common Operator Reference | Select BX-B 120V applications where the original board number matches |
| Accessory Power | 24V accessory output may be present on matching ZBX6 systems; verify board label and transformer wiring before using |
| Control Inputs | Used with compatible open, close, stop, safety, photocell, receiver, and accessory input wiring as shown in the operator manual |
| Programming / Adjustments | DIP switch and adjustment settings may need to be matched to the original board and site requirements |
| Safety Device Note | Photoeyes, edges, loops, and other safety devices must be wired and tested according to the CAME operator manual |
| Installation Type | Electronic board replacement inside compatible CAME BX operator control compartment |
| Handling Note | Electronic circuit board; protect from static discharge, moisture, insects, metal debris, and incorrect wiring |
| Power Safety Note | Disconnect power before service; line-voltage diagnosis should be handled by a qualified technician |
| Notes | Confirm original board number, operator model, voltage, terminal layout, limit wiring, safety devices, and accessory wiring before ordering. |
Also Known As / Related Part Numbers
- CAME 3199ZBX6110
- 3199ZBX6110
- 3199-ZBX6-110
- 3199 ZBX6 110
- ZBX6 110
- ZBX-6 110
- ZBX6 120V
- ZBX-6 120V
- CAME ZBX6
- CAME ZBX-6
- CAME-3199ZBX6110
- CA-3199ZBX6110
- CAME BX Series control board
- CAME BX-B 120V control board
- CAME replacement board for BX Series motors
Related Boards That May Not Be Interchangeable
- ZBX6N - newer replacement board family for some BX Series applications; verify voltage and model before substituting
- ZBX7N - separate BX-related board reference used in some 120V BX listings; not automatically interchangeable with 3199ZBX6110
- ZBX74 / ZBX78 - used on other CAME BX sliding gate platforms; not automatically compatible
- ZN7 - used on select CAME BX-V applications; not a ZBX6 replacement unless documentation confirms it
- ZN8 - used on select CAME BKV applications; not a ZBX6 replacement
- ZBKN - used on select CAME BK Series applications; not a BX ZBX6 board
- ZF1N, ZL37, ZL38, ZL39, ZL65, ZL180 - CAME boards used on other swing gate, barrier gate, or 24V systems; not substitutes for this board
Technician Note
Control board failures on sliding gate operators are often caused by something outside the board. Before replacing the 3199ZBX6110, check the incoming power, transformer, fuses, motor wiring, capacitor if used by the operator, limit switch wiring, receiver, photoeyes, loop detector, edge input, push button wiring, and accessory wiring. A shorted accessory wire can damage a new board immediately.
Take photos of all wiring before removing the old board. Label wires if needed. CAME boards can have multiple command and safety terminals, and a misplaced wire can cause the gate to ignore commands, fail safety checks, run in the wrong direction, or stop at the wrong limit.
After installation, reset the board settings to match the site. Verify DIP switch settings, automatic closing time, safety input behavior, receiver operation, limit switch operation, open/close direction, force or torque settings where applicable, and all required safety devices before returning the gate to service.
Before Ordering, Confirm
- The original board part number is 3199ZBX6110, 3199-ZBX6-110, or a confirmed matching ZBX6 120V board.
- The operator is a compatible CAME BX Series sliding gate operator.
- The system is the 120V / 110V version, not a 230V-only board application.
- The original terminal layout and wiring match the replacement board.
- The motor wiring, limit switches, transformer, fuses, and accessory wiring have been checked.
- The gate is not mechanically binding and the rollers, track, rack, chain, or hardware are in serviceable condition.
- Photoeyes, safety edges, loops, receivers, keypads, and push buttons are not shorted or miswired.
- The installer can safely disconnect and verify line voltage before replacing the board.
- Any receiver, plug-in radio card, transformer, fuses, or external accessories needed for the repair are ordered separately if required.
- The completed gate system will be tested for full open, close, stop, reverse, safety, and limit operation after installation.
Professional Advisory
This is an electronic control board for a line-voltage sliding gate operator. Replacement should be performed by a qualified gate technician when electrical diagnosis, line-voltage service, board wiring, limit setup, or safety-device testing is not clearly understood.
Always disconnect power before servicing the operator. Do not move wires one by one without documenting the original layout. Do not install the board into an operator with unresolved water intrusion, insect damage, burnt wiring, shorted accessories, damaged conduit, or a mechanical gate problem.
Never bypass photoeyes, safety edges, loop detectors, stop circuits, monitored safety devices, or other required protection to make the gate run. After the board is replaced, test every safety device and confirm the gate stops, reverses, or responds correctly according to the operator manual.
Product Q&A
Is the CAME 3199ZBX6110 a LiftMaster control board?
No. The 3199ZBX6110 is best treated as a CAME ZBX6 replacement control board. If your old listing says "LiftMaster + CAME," verify whether that is an old marketplace label or distributor note before publishing.
What operators does the 3199ZBX6110 fit?
It is commonly associated with select CAME BX Series sliding gate operators using a compatible ZBX6 120V / 110V board configuration, including BX-B 120V applications where the original board number matches.
Is this board compatible with every CAME BX operator?
No. CAME BX operators may use different boards depending on model, voltage, generation, and region. Confirm the original board number, operator model, voltage, and wiring diagram before ordering.
Can I replace this board myself?
This board is installed inside a line-voltage gate operator. A qualified gate technician is recommended if you are not comfortable disconnecting power, documenting wiring, checking accessories for shorts, and testing safety devices after installation.
Will this board fix a gate that will not move?
Only if the original board has been correctly diagnosed as failed. A gate that will not move may also have a bad fuse, transformer, receiver, limit switch, motor issue, safety-device fault, wiring short, or mechanical binding.
What should I verify before ordering?
Verify the original board number, CAME BX operator model, 120V / 110V voltage, terminal layout, limit switch wiring, safety device wiring, and whether any accessories caused the original board failure.
