Genie GE-113434.0001.S Rear Actuator Arm Bracket
The Genie GE-113434.0001.S is a rear actuator arm bracket for select Genie GLA24V linear actuator swing gate operator service repairs. Genie service-parts documentation lists 113434.0001.S as the rear actuator arm bracket, making this a mechanical mounting part used at the rear or post-side actuator connection where the parts diagram confirms fitment.
This is a bracket service part only. It is not the complete actuator arm, front actuator bracket, push open bracket, control box, post mount kit, battery kit, gate operator, or safety device. Match this part by exact part number, operator model, rear bracket location, mounting geometry, gate swing layout, and existing hardware before ordering.
Primary Use
- Replacement rear actuator arm bracket for select Genie GLA24V linear actuator swing gate operator installations
- Used at the rear or post-side actuator mounting location where 113434.0001.S is listed in the service parts diagram
- Helps secure the actuator arm to the rear mounting point when the original bracket is bent, worn, cracked, damaged, or missing
- Used in repairs where the original bracket is marked, ordered, or cross-referenced as 113434.0001.S
- Applies only where the post location, rear bracket geometry, hinge offset, and Genie installation dimensions support this bracket
Compatible With
Use this bracket only where the installed Genie operator and parts documentation confirm 113434.0001.S as the correct rear actuator arm bracket. Do not assume it fits every Genie swing gate operator, slide gate operator, or non-Genie linear actuator system.
- Select Genie GLA24V residential linear actuator swing gate operator installations where the service parts list shows 113434.0001.S
- Repairs where the existing bracket is the rear actuator arm bracket and not the front bracket or push open bracket
- Applications where the post-side mounting point, actuator pin location, bracket angle, and hinge geometry match the Genie installation requirements
- Single or dual GLA24V installations where the specific gate leaf uses this rear bracket and the parts diagram confirms fitment
Features and Specifications
| Specification | Details |
| Brand | Genie |
| Part Number | GE-113434.0001.S / 113434.0001.S |
| Service Description | Bracket, Actuator Arm, Rear |
| Product Type | Rear actuator arm bracket / mechanical mounting service part |
| Used With | Select Genie GLA24V linear actuator swing gate operator installations where specified |
| Mounting Location | Rear/post-side actuator arm mounting point, where shown in the Genie parts diagram |
| Electrical Function | None; this is a mechanical bracket |
| Programming Required | No programming for the bracket itself; operator travel, force, limits, and safety devices should be checked after bracket work |
| Package Contents | Confirm before ordering; treat as the rear bracket only unless bolts, pins, clips, washers, nuts, or other hardware are specifically listed |
Important Comparison With Similar Genie Brackets
Genie actuator brackets can look similar but are used in different locations. Ordering the wrong bracket can create poor actuator geometry, travel problems, binding, or bracket damage.
- GE-113434.0001.S / 113434.0001.S: Rear actuator arm bracket for select GLA24V applications.
- 113433.0001.S: Front actuator arm bracket. This is a related but different bracket and should not be substituted for the rear bracket without confirming the parts diagram.
- 113374.0001.S: Push open bracket for supported push-to-open GLA24V installations. This is not the same as the rear actuator bracket.
- 113435.0001.S: Post mount actuator control box kit. This is a mounting accessory and not the rear actuator arm bracket.
- GLA24V actuator arm: Not the same part. The actuator arm is a separate component from the rear bracket.
- Complete GLA24V single or dual kit: Not the same item. This listing should be treated as the rear bracket service part only.
Also Known As / Related Part Numbers
- GE-113434.0001.S
- 113434.0001.S
- GE1134340001S
- 1134340001S
- Genie GE-113434.0001.S
- Genie 113434.0001.S
- Genie rear actuator arm bracket
- Bracket, Actuator Arm, Rear
- Rear actuator bracket for Genie GLA24V
- Genie GLA24V post-side actuator bracket
- Genie linear actuator rear mounting bracket
- 113433.0001.S - related front actuator arm bracket, not the same part
- 113374.0001.S - related push open bracket, not the same rear actuator bracket
- 113435.0001.S - related post mount kit, not the same part
Technician Notes
- Confirm the operator is a Genie GLA24V before ordering this bracket. Do not assume it fits GRSW24V, GRSL24V, GCSW36V, GCSL36V, or other actuator systems.
- Verify that the damaged or missing part is the rear actuator bracket, not the front bracket or optional push open bracket.
- Inspect the post or rear mounting surface where the bracket attaches. A bent rear bracket may be a symptom of weak post material, loose mounting hardware, poor hinge offset, incorrect geometry, or actuator overtravel.
- Check the actuator pin, clevis, bushings, cotter clips, and related hardware for wear before replacing only the bracket.
- If the rear bracket was bent, inspect for binding at full open and full close. The actuator should not bottom out, twist, rub, or force the bracket past its intended travel.
- Check the matching front actuator bracket and gate-side mounting area. A rear bracket failure can sometimes be caused by front bracket misalignment or gate frame movement.
- After replacement, verify manual gate movement, actuator alignment, open and close limits, force settings, safety-device function, and warning devices before returning the operator to service.
- Do not drill, weld, or modify the bracket unless the installation documentation and gate structure support the change. Poor geometry can damage the actuator or create unsafe gate movement.
Before Ordering Checklist
- Confirm the exact part number is GE-113434.0001.S or 113434.0001.S.
- Confirm the installed operator is a Genie GLA24V linear actuator swing gate operator.
- Confirm you need the rear actuator arm bracket, not the front bracket, push open bracket, post mount kit, or actuator arm.
- Confirm the post-side mounting location, hole pattern, bracket angle, actuator pin location, and existing hardware match the parts diagram.
- Inspect the post, hinge offset, gate frame, fasteners, actuator arm, clevis, pins, front bracket, and gate stops before ordering only the rear bracket.
- Confirm whether bolts, nuts, washers, pins, clips, bushings, or mounting hardware are included.
- Confirm the original bracket failure was not caused by gate binding, sagging hinges, incorrect push-to-open geometry, actuator overtravel, weak post material, or impact damage.
Professional Advisory
The rear actuator arm bracket affects actuator alignment, gate travel, force, and safe operation. If the bracket is bent, torn loose, repeatedly breaking, or mounted to a weak post, have the gate inspected by a qualified gate operator technician before replacing parts. Do not force the operator to run with incorrect geometry, damaged brackets, missing pins, bypassed safety devices, or binding gate movement. After any bracket repair, monitored photo eyes, safety edges, inherent entrapment protection, limits, force settings, warning signs, and manual release operation should be verified.
Product Q&A
What is Genie GE-113434.0001.S used for?
Genie GE-113434.0001.S is the rear actuator arm bracket for select Genie GLA24V linear actuator swing gate operator installations where the parts diagram lists 113434.0001.S.
Is GE-113434.0001.S the same as the front actuator bracket?
No. GE-113434.0001.S is the rear actuator arm bracket. The front actuator arm bracket is a separate Genie service part and should not be treated as the same item.
Does this bracket fit every Genie swing gate operator?
No. This bracket should be matched to select Genie GLA24V applications where the service parts diagram confirms fitment. Do not assume it fits other Genie swing, slide, or commercial operator models.
Is this the same as the Genie push open bracket?
No. The push open bracket is a different Genie accessory used for supported push-to-open GLA24V installations. GE-113434.0001.S is the rear actuator arm bracket.
Does this listing include the actuator arm or mounting hardware?
Do not assume the actuator arm, pins, bolts, washers, nuts, clips, or mounting hardware are included. Treat this as the rear bracket only unless the supplier package specifically lists additional parts.
What can cause a rear actuator bracket to bend or break?
Common causes include gate binding, sagging hinges, weak post material, incorrect bracket geometry, actuator overtravel, missing gate stops, impact damage, or worn actuator pins and hardware.
What should I check after replacing this bracket?
Check manual gate movement, actuator alignment, pin and clevis fit, open and close limits, force settings, gate stops, safety photo eyes, safety edges, warning devices, and full travel before returning the gate to service.
