Genie GE-113465.0001.S Handheld Programming Pendant
The Genie GE-113465.0001.S is a handheld programming pendant used with select Genie gate operator setup and service applications. Genie specification language describes the accessory as a handheld programming pendant with a multi-line backlit LCD display and a 6 ft cable, while distributor listings commonly identify 113465.0001.S as a Genie handheld programming pendant for gate openers with a 72 inch cable.
This item should be treated as a wired programming/setup pendant only unless the supplier package specifically states otherwise. It is not a handheld radio transmitter, keypad, receiver, logic board, motor drive PCB, LCD board, control enclosure, reset button, or complete operator controller. Match this part by exact part number, operator model, pendant connector style, cable length, board compatibility, and package contents before ordering.
Primary Use
- Handheld programming pendant for select Genie gate operator setup and service work
- Used where compatible Genie gate operator documentation supports a wired programming pendant accessory
- Provides off-board access to setup, status, or programming functions where supported by the operator
- Useful for technicians working inside a control box where pendant-style access is preferred for setup or diagnostics
- Service replacement where the original accessory is marked, ordered, or cross-referenced as GE-113465.0001.S or 113465.0001.S
Compatible With
Use this programming pendant only where the installed Genie operator documentation confirms 113465.0001.S or a compatible handheld programming pendant accessory. Do not assume it fits every Genie gate operator, Genie garage door opener, or operator control board.
- Select Genie GRSW24V residential swing gate operator applications where the handheld programming pendant accessory is supported
- Select Genie GRSL24V residential slide gate operator applications where the control system supports pendant programming
- Select Genie GLA24V linear actuator swing gate operator applications where the control board, connector, and documentation support the pendant
- Compatible Genie gate operator control systems using a multi-line backlit LCD setup/status interface where pendant programming is specified
- Repairs or service setups where the original pendant is identified as GE-113465.0001.S or 113465.0001.S
Features and Specifications
| Specification | Details |
| Brand | Genie |
| Part Number | GE-113465.0001.S / 113465.0001.S |
| Service Description | Pendant, Handheld, Programming, Genie |
| Product Type | Handheld programming pendant / wired setup accessory |
| Display | Multi-line backlit LCD display where supplied as described by Genie specification language |
| Cable Length | 6 ft / 72 in cable where supplied as commonly listed |
| Primary Function | Programming, setup, status review, and service access where supported by the connected Genie gate operator |
| Wireless Function | None assumed; this is a wired programming accessory, not a radio transmitter or receiver |
| Receiver / Keypad Included | Not included unless supplier package specifically lists additional access control accessories |
| Logic Board Included | Do not assume included; the logic board is a separate service part unless specifically listed |
| Compatibility Requirement | Requires a compatible Genie gate operator control board and correct pendant connector where specified by documentation |
| Package Contents | Confirm before ordering; treat as the handheld programming pendant only unless adapters, brackets, instructions, or other accessories are specifically listed |
Important Comparison With Similar Genie Control Accessories
The programming pendant is easy to confuse with remote controls, keypads, and control boards because all of these parts can relate to setup or access. Confirm the exact function and part number before ordering.
- GE-113465.0001.S / 113465.0001.S: Handheld programming pendant for select compatible Genie gate operator setup and service work.
- 113440.0001.S: Logic board assembly. The logic board may communicate with the pendant, but it is not the pendant itself.
- 113429.0001.S: 24V motor drive PCB assembly. This is an electronic motor drive board and not a programming pendant.
- 113436.0001.S: Linear actuator reset button. This is a reset switch component and not a programming accessory.
- 113442.0001.S: UL325 gate operator buzzer. This is an audible warning component and not a programming pendant.
- OPAKCDCM-S: Genie Wi-Fi connectivity module kit. This is a connectivity accessory and not the same as the wired programming pendant.
- G1BT-P / 41538R style transmitters: Handheld gate remotes used for access control. These are radio transmitters and not programming pendants.
- External keypads or receivers: Used for access control input, not for the same wired setup/programming function as this pendant.
Also Known As / Related Part Numbers
- GE-113465.0001.S
- 113465.0001.S
- GE1134650001S
- 1134650001S
- Genie GE-113465.0001.S
- Genie 113465.0001.S
- Genie handheld programming pendant
- Genie gate opener programming pendant
- Genie programming pendant with 72 inch cable
- Handheld programming pendant with 6 ft cable
- Pendant, Handheld, Programming, Genie
- Wired programming pendant for Genie gate operators
- Genie LCD programming pendant
- Multi-line backlit LCD programming pendant
- 113440.0001.S - related logic board assembly, not the same part
- 113429.0001.S - related 24V motor drive PCB assembly, not the same part
- 113436.0001.S - related reset button, not the same part
- 113442.0001.S - related UL325 buzzer, not the same part
- OPAKCDCM-S - related Wi-Fi connectivity module kit, not the same part
- 41538R / G1BT-P - related Genie gate transmitter, not the same part
Technician Notes
- Confirm the installed operator supports this programming pendant before ordering. A pendant connector on one model does not guarantee compatibility with every Genie control board or software revision.
- Do not confuse this with a handheld transmitter. A transmitter opens or controls the gate by radio; this pendant is for wired setup and service access where supported.
- If the pendant display is blank or unresponsive, check the operator power, logic board status, connector condition, cable damage, and board fault status before replacing the pendant.
- If menu navigation or setup functions do not respond, inspect for bent connector pins, water intrusion, damaged cable strain relief, board communication faults, or incorrect operator compatibility.
- Do not use the pendant to change safety-related settings without verifying monitored photo eyes, safety edges, entrapment zones, gate movement, and operator setup requirements.
- After programming or setup changes, verify travel limits, force settings, motor direction, timer-to-close, primary/secondary setup, monitored safety inputs, accessory functions, and full gate operation.
- Keep the pendant cable away from moving gate parts, drive arms, belts, chains, exposed terminals, batteries, and sharp enclosure edges during service.
- Do not leave the pendant connected or hanging inside the enclosure unless the operator documentation and service procedure specifically allow it.
Before Ordering Checklist
- Confirm the exact part number is GE-113465.0001.S or 113465.0001.S.
- Confirm the installed Genie gate operator documentation supports the handheld programming pendant accessory.
- Confirm the connector style, cable length, control board compatibility, and board revision before ordering.
- Confirm you need the programming pendant, not a handheld transmitter, keypad, receiver, Wi-Fi module, logic board, reset button, or LCD/control board assembly.
- Inspect the existing pendant, cable, connector, display, buttons, cable strain relief, and signs of water or impact damage.
- Check operator power, logic board status, fuses, batteries, power supply, and fault information before replacing a non-responsive pendant.
- Confirm whether adapters, instructions, mounting clips, storage brackets, or accessories are included.
- Confirm that setup changes will be performed by someone familiar with Genie gate operator menus, monitored safety-device requirements, and proper gate operation testing.
Professional Advisory
A programming pendant can access operator settings that affect gate travel, force, speed, timer behavior, relay functions, primary/secondary timing, monitored safety inputs, and diagnostic status. Incorrect setup can create nuisance faults, unreliable operation, or unsafe gate movement. Programming and troubleshooting should be handled by a qualified gate operator technician when the system involves monitored photo eyes, safety edges, dual-gate timing, fire access, relay wiring, unknown prior modifications, or repeated faults. Do not use the pendant to bypass monitored entrapment protection, reset circuits, fuses, grounding, warning devices, or operator safeguards.
Product Q&A
What is Genie GE-113465.0001.S used for?
Genie GE-113465.0001.S is a handheld programming pendant used with select Genie gate operators for wired setup, programming, status review, and service functions where supported by the operator documentation.
Is GE-113465.0001.S a gate remote control?
No. GE-113465.0001.S is a wired programming pendant, not a handheld radio transmitter, access remote, keypad, or receiver.
How long is the cable on this programming pendant?
Genie specification language describes the handheld programming pendant with a 6 ft cable, and distributor listings commonly describe 113465.0001.S with a 72 inch cable.
Does this pendant include the logic board?
No. The logic board is a separate Genie service part unless the supplier package specifically lists it. This item should be treated as the programming pendant only.
Which Genie gate operators use this pendant?
This pendant is associated with select Genie gate operators that support a handheld programming pendant accessory, including compatible residential 24V gate operator platforms where the documentation confirms use.
Can a programming pendant fix a gate that will not run?
Usually no. The pendant may help with setup or diagnostics, but a no-run condition can be caused by power supply faults, weak batteries, safety inputs, wiring problems, logic board failure, motor drive issues, or actuator problems.
What should I check before replacing the programming pendant?
Check the operator model, pendant connector, cable condition, display, buttons, logic board status, power supply, batteries, fuses, water intrusion, and whether the operator actually supports GE-113465.0001.S.
