HySecurity MX001746 Top Cap Cover Details
The HySecurity MX001746 is a replacement top cap cover used on HySecurity SwingSmart DC gate operators. This part covers the top section of the SwingSmart DC operator housing and is commonly replaced when the original top cap is cracked, missing, weathered, damaged by impact, or no longer fitting securely.
This is the top cap cover only. Public listings specifically note that the top cap knob is not included. If the knob, side covers, front cover, rear cover, latches, or hardware are also damaged or missing, those items should be inspected and ordered separately where required.
The top cap helps protect the upper portion of the operator enclosure from normal outdoor exposure. A damaged or missing cap can allow water, debris, insects, and sunlight to reach areas that should remain covered. On older SwingSmart DC operators, a brittle or UV-damaged top cap may crack when removed for service, especially if the knob or cover hardware has been overtightened.
Compatible With
The HySecurity MX001746 top cap cover is commonly associated with the following operator and service applications:
- HySecurity SwingSmart DC gate operators
- Nice HySecurity SwingSmart DC operator assemblies
- SwingSmart DC models where the parts diagram calls for MX001746
- SwingSmart DC top cover cap replacement
- SwingSmart DC enclosure cover service
- Replacement of an original top cap cover identified as MX001746
Not Intended For
- Replacing the top cap knob. The knob is a separate part unless your listing states otherwise.
- Replacing the complete 3-piece cover kit, front cover, rear cover, side covers, latches, or enclosure hardware.
- HySecurity SlideSmart, SlideDriver, StrongArm, StrongArmPark, HydraSwing, HydraWedge, HydraLift, WedgeSmart, SwingRiser, or barrier operators unless the correct parts diagram specifically calls for MX001746.
- Replacing damaged internal electrical parts, control boards, power supplies, batteries, motors, gearboxes, or drive assemblies.
- Correcting water intrusion caused by missing seals, damaged lower covers, cracked enclosure panels, poor conduit sealing, or an improperly mounted operator.
- Universal cover replacement where operator model, housing shape, mounting fit, and parts diagram have not been verified.
Important Ordering Warnings
- Confirm the exact HySecurity part number before ordering. This listing is for MX001746.
- Official HySecurity SwingSmart DC parts documentation lists MX001746 as Cover, Top Cap for SwingSmart DC models.
- Public listings describe this as the SwingSmart top cap cover only and note that the knob is not included.
- Do not confuse MX001746 with the top cap knob, commonly listed separately as MX001703.
- Do not confuse this single top cap cover with the 3-piece cover kit, commonly listed as MX001926.
- If the original cover was damaged by impact or repeated vibration, inspect the operator housing, knob, cover fit, and latch hardware before installing the replacement.
- If water has entered the operator, inspect the internal electrical components before returning the system to service.
Features & Specifications
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX001746 |
| Product Type | Top Cap Cover |
| Common Description | Cover, Top Cap / Top Cap Cover / TOP CAP, ROTOMOLD, SWINGSMART |
| Compatible Operator Family | HySecurity SwingSmart DC, where MX001746 is shown in the parts diagram |
| Operator Type | Swing gate operator |
| Application | Replacement top cap cover for the SwingSmart DC operator housing |
| Included Items | Top cap cover only, unless otherwise stated by the product listing |
| Knob Included | No. Public listings note that the knob is not included. |
| Related Cover Kit | MX001926 is commonly listed as a related 3-piece cover kit for SwingSmart DC; verify before ordering |
| Approximate Item Weight | Some public listings show approximately 5 lbs. shipping weight; verify actual shipping weight if needed |
| Important Notes | Verify operator model, parts diagram, knob condition, cover fit, and related housing hardware before ordering. |
Also Known As / Related Part Numbers
- HySecurity MX001746
- Nice HySecurity MX001746
- MX001746
- HySecurity Cover, Top Cap
- HySecurity Top Cap Cover
- Cover, Top Cap, SwingSmart DC
- SwingSmart DC Top Cap Cover
- SwingSmart Top Cap Cover Only
- TOP CAP, ROTOMOLD, SWINGSMART
- HYS-MX001746 - related distributor SKU format used by some sellers
- MX001703 - related top cap knob, not included with MX001746 unless specifically stated
- MX001926 - related 3-piece cover kit for SwingSmart DC, not the same as the top cap cover only
Common Related Items
Depending on the condition of the operator housing, the following related components may also need to be inspected:
- Top cap knob
- 3-piece cover kit
- Front cover
- Rear cover
- Side cover latches
- Cover screws, wing nuts, and related fasteners
- Operator housing seals and enclosure contact points
- Internal electrical components if the operator has been exposed to water or debris
- Chassis and cover mounting points if the original cover was impact-damaged
Technician Note
The top cap is a protective cover part, but it still matters for operator reliability. A missing or cracked top cap can allow water, insects, dust, and debris into the operator housing. Before replacing the cap, check the knob, cover fit, cover latches, and mounting points. If the old cap cracked because the knob was overtightened or the cover was forced during service, correct that issue before installing the new cap.
If the operator has been running with the top cap missing or damaged, inspect the inside of the enclosure for water marks, corrosion, insect nests, loose wiring, and damaged electrical components before returning the gate to service.
Before Ordering, Confirm
- The required replacement part number is HySecurity MX001746.
- The operator is a compatible HySecurity SwingSmart DC model.
- The parts diagram calls for the MX001746 top cap cover.
- The top cap knob is still usable or is being ordered separately if damaged or missing.
- The 3-piece cover kit is not required instead of the top cap only.
- The front cover, rear cover, side cover latches, and enclosure hardware are not also damaged.
- The operator housing has not been bent or damaged in a way that prevents the top cap from seating properly.
- No water, insects, debris, or corrosion entered the operator while the cap was damaged or missing.
- You are ordering the top cap cover only, not a complete cover kit or operator enclosure.
Professional Advisory
Cover replacement is usually a straightforward service item, but the operator should still be powered down before removing covers or reaching inside the enclosure. Disconnect power as required by the service procedure before inspecting internal electrical components.
If the top cap was damaged by impact, vandalism, severe weather, or repeated water intrusion, inspect the full operator housing and internal components before returning the system to service. A replacement cover should not be used to hide existing electrical or enclosure damage.
Product Questions & Answers
What is the HySecurity MX001746 used for?
The HySecurity MX001746 is a replacement top cap cover used on SwingSmart DC gate operators.
Does MX001746 include the top cap knob?
No. Public listings note that MX001746 is the top cap cover only and that the knob is not included.
Which operator does MX001746 fit?
Official HySecurity SwingSmart DC parts documentation lists MX001746 as the top cap cover for SwingSmart DC models. Always verify the operator parts diagram before ordering.
Is this the full 3-piece cover kit?
No. MX001746 is the top cap cover only. The related 3-piece cover kit is commonly listed separately as MX001926.
What part number is the top cap knob?
The related top cap knob is commonly listed as MX001703. Verify the knob part number against the current SwingSmart DC parts diagram before ordering.
Should I replace the top cap if it is cracked?
Yes. A cracked or missing top cap can allow water, insects, and debris into the operator housing. Inspect the enclosure and related hardware before installing the replacement.
What should I check before ordering this cover?
Check the operator model, parts diagram, knob condition, cover latches, front and rear covers, mounting points, and any signs of water or impact damage before ordering.
