HySecurity MX002085 SlideSmart Target Sensor Switch Details
The HySecurity MX002085 is a target sensor switch used on select HySecurity SlideSmart gate operator applications. HySecurity parts documentation lists MX002085 as a target sensor / target sensor switch for SlideSmart DC and SlideSmart HD systems. This part is used in the target sensing area of the operator and should be matched to the original installed sensor before ordering.
This is the sensor side of the target assembly relationship. The related target magnet is a separate part number, MX002087. A target sensing problem can be caused by the sensor, target magnet, sensor alignment, wiring, connector, controller input, or mechanical movement of the operator, so the full sensor circuit should be checked before replacing parts.
What This Part Does
The MX002085 target sensor switch helps the SlideSmart operator detect the target reference used by the control system. When the sensor, magnet, wiring, and mounting position are correct, the operator can read the target condition as part of its normal monitored movement and position-reference operation.
- Replaces the target sensor / target sensor switch on select HySecurity SlideSmart operators.
- Used with the related MX002087 target magnet assembly.
- Mounts on the operator in the target sensor location.
- Helps the operator read the proper target reference when aligned correctly.
- Commonly associated with SlideSmart DC target proximity sensor listings.
- Listed in SlideSmart HD parts documentation as target sensor / target sensor switch.
- Used for repair situations where the original installed part is confirmed as MX002085.
Compatible With
The HySecurity MX002085 is commonly associated with the following select HySecurity SlideSmart applications. Always verify by the operator model label, production generation, installed sensor, wiring, and current replacement parts diagram before ordering.
- Select HySecurity SlideSmart DC gate operators.
- Select HySecurity SlideSmart HD gate operators.
- SlideSmart DC models where the parts list calls out MX002085 as "Target, Sensor Switch, SlideSmart."
- SlideSmart HD models where the parts diagram calls out MX002085 as "Target, Sensor" or "Target, Sensor Switch, SlideSmart."
- Repairs where the original sensor label, diagram, or service documentation identifies MX002085.
- Applications using the related MX002087 target magnet when the sensor and magnet alignment match the factory layout.
Important Compatibility Warning
Do not order MX002085 based only on the word "sensor." HySecurity operators may use target sensors, target magnets, reset switches, on/off switches, Hall-effect motor sensors, vehicle detector modules, limit-related parts, and controller inputs that can look similar in a troubleshooting conversation but are not the same part.
MX002085 is not the magnet. The related magnet / target magnet assembly is MX002087. If the magnet is missing, damaged, loose, misaligned, or mounted too far from the sensor, replacing only the sensor may not correct the fault.
Exact public compatibility beyond SlideSmart DC and SlideSmart HD parts-list references should be verified before publishing guaranteed model fitment. Confirm the operator model, serial range if available, production generation, controller platform, mounting bracket, wire routing, connector style, and current HySecurity parts diagram.
Comparison With Similar HySecurity Parts
- MX002085: Target sensor / target sensor switch for select SlideSmart operator applications.
- MX002087: Related target magnet / target magnet assembly. Not the same as the MX002085 sensor.
- MX002124: Internal reset switch used on SlideSmart parts lists. Not a target sensor.
- MX001761: On/off switch used on SlideSmart parts lists. Not a target sensor.
- MX002573: Motor with Hall-effect sensor reference in SlideSmart HD parts lists. Not the same as the target sensor switch.
- MX4125 / MX4621: Hy5B vehicle detector references. These detect vehicle loop inputs and are not target sensors.
Similar Parts That Are Not Automatically Interchangeable
- HySecurity MX002087 target magnet assembly.
- HySecurity internal reset switches.
- HySecurity on/off switches.
- Motor Hall-effect sensor assemblies.
- Vehicle detector modules.
- Limit switch parts from other HySecurity operator families.
- Sensors used on SwingSmart, StrongArmPark, SlideDriver, HydraWedge, WedgeSmart, or other HySecurity systems unless the parts diagram specifically calls out MX002085.
- Generic proximity sensors with similar shape but different output, connector, voltage, mounting, or environmental rating.
Not Intended For
- Replacing the MX002087 target magnet assembly.
- Replacing a SlideSmart controller board, motor, gearbox, belt, sprocket, or vehicle detector.
- Correcting a gate that is dragging, binding, off track, or mechanically overloaded without repairing the gate first.
- Bypassing target sensing, monitored safety devices, photo eyes, safety edges, emergency access, fire access, or UL 325 entrapment protection devices.
- Use on non-SlideSmart operators unless the current HySecurity parts diagram confirms MX002085.
- Unsafe wiring diagnosis or controller input testing by an unqualified person.
Features and Specifications
| Specification |
Details |
| Brand |
HySecurity |
| Part Number |
MX002085 |
| Store Reference |
Hy-MX002085 |
| Product Type |
Target sensor / target sensor switch |
| Common Description |
Target proximity sensor for SlideSmart, mounts on operator |
| Operator Family |
Select HySecurity SlideSmart DC and SlideSmart HD operators |
| Related Magnet |
MX002087 target magnet / target magnet assembly, sold separately unless confirmed |
| Mounting Location |
Operator target sensor location, verify against parts diagram |
| Electrical Details |
Verify voltage, output type, wire length, and connector style against the original sensor and current manual |
| Package Contents |
Target sensor switch only unless supplier confirms bracket, hardware, wiring, or magnet is included |
| Installation Level |
Qualified gate operator technician recommended |
Also Known As / Related Part Numbers
- MX002085
- Hy-MX002085
- HySecurity MX002085
- HySecurity target sensor
- HySecurity target sensor switch
- SlideSmart target sensor switch
- SlideSmart DC target proximity sensor
- Target proximity sensor, SlideSmart
- Target, Sensor
- Target, Sensor Switch, SlideSmart
- MX002087 - related target magnet / target magnet assembly
- MX002124 - related reset switch, not interchangeable
- MX001761 - related on/off switch, not interchangeable
Related Parts and Service Checks
- Confirm the original installed sensor is MX002085.
- Confirm whether the related MX002087 target magnet is present and aligned.
- Inspect the target magnet for damage, loose mounting, missing hardware, or improper spacing.
- Inspect sensor wiring for cuts, pulled conductors, water intrusion, corrosion, or damaged connector pins.
- Confirm the sensor bracket and mounting location match the factory parts diagram.
- Confirm the controller input is reading correctly before replacing multiple parts.
- Check the gate and drive system for binding, worn parts, or movement problems that could affect the target relationship.
- Confirm all required photo eyes, safety edges, warning devices, and monitored safety inputs are installed and working.
Technician Note
The common field mistake is replacing the sensor when the magnet is the actual issue, or replacing the magnet when the sensor wiring is damaged. Check the sensor and MX002087 magnet together. Spacing, alignment, mounting, and wiring matter as much as the part number.
If the operator has intermittent target faults, look for loose mounting hardware, vibration, worn drive components, water in the harness, damaged connector pins, or a controller input problem before assuming the new sensor will solve the issue.
Before Ordering Checklist
- Confirm the exact part number needed is MX002085.
- Confirm the operator is a compatible HySecurity SlideSmart DC or SlideSmart HD model.
- Confirm the original part is the target sensor switch, not the target magnet.
- Confirm whether MX002087 target magnet is also needed.
- Confirm sensor mounting location and bracket condition.
- Confirm wire length, connector style, and routing before ordering.
- Confirm the controller input and wiring are not the actual failure point.
- Confirm the gate and operator move smoothly without binding or mechanical interference.
- Confirm all monitored safety devices remain connected and working after service.
Installation and Service Notes
Installation should be handled by a qualified gate operator technician familiar with HySecurity SlideSmart systems. The sensor must be mounted in the correct location, aligned with the related target magnet, wired correctly, and tested through normal gate travel. Do not bypass the target sensor circuit, monitored safety inputs, photo eyes, safety edges, emergency access, or fire access devices to force the operator to run.
For South Florida customers, Gate Openers Unlimited may be able to assist with availability and Hialeah Gardens local pickup when appropriate. Bring the operator model number, serial information if available, photos of the old sensor, photos of the target magnet, and the current fault history when matching this part locally.
Professional Advisory
A target sensor fault can be caused by sensor failure, magnet failure, alignment, damaged wiring, loose hardware, water intrusion, controller input trouble, or mechanical movement problems. If the failure is unclear or the gate has safety-device faults, have the operator inspected by a qualified gate technician before replacing parts or returning the gate to automatic operation.
Product Questions & Answers
What is the HySecurity MX002085?
The MX002085 is a HySecurity target sensor / target sensor switch used on select SlideSmart gate operator applications, including SlideSmart DC and SlideSmart HD parts-list references.
Is MX002085 the same as the target magnet?
No. MX002085 is the target sensor switch. The related target magnet assembly is MX002087 and should be verified separately if the magnet is missing, damaged, loose, or misaligned.
What operators use the MX002085 target sensor?
HySecurity parts documentation lists MX002085 for select SlideSmart DC and SlideSmart HD operator applications. Confirm the exact operator model and current parts diagram before ordering.
Does MX002085 include the magnet or mounting hardware?
Do not assume the magnet, bracket, wiring hardware, or fasteners are included. Treat MX002085 as the target sensor switch unless the current supplier package confirms additional parts.
Can a target sensor fault be caused by something other than the sensor?
Yes. A target fault may be caused by the sensor, MX002087 magnet, alignment, wiring, connector damage, controller input trouble, or mechanical movement problems in the operator.
How should MX002085 be checked before replacement?
Check the original sensor label, operator model, wiring condition, connector, mounting location, target magnet alignment, controller input, and parts diagram before replacing the sensor.
Is MX002085 interchangeable with reset switches or motor sensors?
No. MX002085 is a SlideSmart target sensor switch. It should not be substituted for reset switches, on/off switches, motor Hall sensors, vehicle detectors, or sensors from other HySecurity operator families.
Can the operator be run with the target sensor bypassed?
No. Do not bypass target sensing, monitored photo eyes, safety edges, emergency access, fire access, or UL 325 safety circuits. A qualified gate technician should diagnose sensor and safety input problems.
