HySecurity MX002219, Cylinder, Position Sensing, 2.5 x 14 inch
The HySecurity MX002219 is a 2.5 x 14 inch position-sensing hydraulic cylinder for select HySecurity / Nice HySecurity hydraulic gate operator applications. This type of cylinder provides hydraulic movement while also supporting position feedback used by compatible operator controls.
This is a precision hydraulic and sensing component, not a basic cylinder swap. The bore size, stroke length, mounting points, sensor function, hose/fitting arrangement, and operator control compatibility must match the original equipment. Before ordering, verify MX002219 against the operator model, serial number, existing cylinder label, and current HySecurity parts diagram.
What This Position-Sensing Cylinder Does
The cylinder provides the hydraulic force needed to move the gate, arm, or lift mechanism in a compatible HySecurity operator. The position-sensing feature allows the operator control system to monitor cylinder travel or position feedback where that function is required by the operator design.
If the original cylinder includes position sensing, it should not be replaced with a non-sensing cylinder unless HySecurity documentation specifically confirms the substitution. A missing, incorrect, or failed position sensor can cause travel faults, incorrect movement feedback, control errors, or unsafe operation depending on the operator model.
Compatible With
This cylinder may be used with the following applications only where the current HySecurity parts diagram confirms MX002219:
- Select HySecurity hydraulic gate operator applications requiring a 2.5 x 14 inch position-sensing cylinder
- Repairs where the original cylinder is marked, tagged, listed, or cross-referenced as MX002219
- Applications where the operator control system requires cylinder position feedback
- Hydraulic operator assemblies using the correct mounting pin size, stroke length, hose routing, and sensor wiring for MX002219
- Operator models where the current HySecurity parts diagram specifically lists MX002219 for the cylinder assembly
Important: Public listings for MX002219 do not all show the same model-family compatibility. Do not order this cylinder based only on a general model name. Confirm the part number by serial number, parts diagram, and the label or markings on the existing cylinder.
Similar Parts That Are Not Interchangeable
HySecurity hydraulic cylinders can look similar but may not be interchangeable. Bore size, stroke length, sensor type, rod end, mounting hardware, hose ports, fittings, and operator control requirements all matter.
| Part / Cylinder Type | Common Description | Interchangeability Note |
| MX002219 | 2.5 x 14 inch position-sensing hydraulic cylinder | Use where MX002219 is listed by the current HySecurity parts diagram |
| Non-sensing hydraulic cylinder | Hydraulic cylinder without position feedback | Not a direct substitute when the operator requires position feedback |
| Different bore or stroke cylinder | Cylinder with different size or travel | Not interchangeable unless HySecurity documentation confirms the exact replacement |
| MX002605 | Related HySecurity position-sensing cylinder reference for certain StrongArm M30/M50 diagrams | Not the same part number as MX002219; verify before ordering |
Not Intended For
- Operators that require a different cylinder bore or stroke length
- Operators that require a non-sensing hydraulic cylinder
- Operators that use a different sensor style, connector, or position feedback method
- Applications where the mounting pins, rod end, ports, hoses, or fittings do not match
- StrongArm, SwingRiser, HydraLift, or other HySecurity hydraulic models unless the current parts diagram specifically lists MX002219
- General hydraulic cylinder replacement outside confirmed HySecurity operator applications
- Bypassing position feedback, hydraulic controls, limits, safety devices, or controller protections
Important Compatibility Warning
The MX002219 cylinder must be verified carefully because public compatibility references are not completely consistent. Some listings associate the part with StrongArm M30/M50, while another listing associates it with SwingRiser and HydraLift. Because HySecurity hydraulic cylinders are model-specific and control-system-specific, the current parts diagram should be treated as the deciding reference.
Do not substitute a similar-looking cylinder based only on size. A 2.5 x 14 inch cylinder without the correct position-sensing hardware, mounting geometry, hose port location, fittings, or connector style may not operate correctly and may create a safety issue.
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX002219 |
| Product Type | Hydraulic position-sensing cylinder |
| Cylinder Size | 2.5 x 14 inch |
| Bore | 2.5 inch |
| Stroke | 14 inch |
| Position Sensing | Yes, where connected to a compatible HySecurity control system |
| Common Use | Select HySecurity hydraulic operator applications where MX002219 is specified |
| Hydraulic Considerations | Hoses, fittings, ports, seals, fluid condition, and pressure settings must be checked during service |
| Package Contents | Cylinder assembly; confirm included sensor lead, fittings, pins, hardware, and current package contents before ordering |
Also Known As / Related Part Numbers
- MX002219
- MX-002219
- HySecurity MX002219
- Nice HySecurity MX002219
- HYS-MX002219
- HYS MX002219
- HySecurity Cylinder, Position Sensing, 2.5 x 14 inch
- HySecurity Position-Sensing Cylinder 2.5 x 14 inch
- HySecurity Hydraulic Position-Sensing Cylinder
- 2.5 x 14 Inch Position-Sensing Hydraulic Cylinder
- Cylinder Assembly with Position Sensor
- MX002605 - related HySecurity position-sensing cylinder reference, not the same part number
Related Parts and Accessories
- Hydraulic hose assemblies matched to the specific operator and cylinder port layout
- Cylinder mounting pins, retaining hardware, bushings, or bearings where listed in the parts diagram
- Hydraulic fittings and seals where the current parts diagram confirms the correct type and size
- Hydraulic fluid approved for the specific HySecurity operator
- Position sensor wiring, connector, or controller input components where listed separately
- Hydraulic pump, manifold, valve, or pressure components if cylinder movement is weak, uneven, or drifting
Technician Note
A position-sensing cylinder can be blamed for problems that are actually caused by other components. Before replacing the MX002219, inspect the cylinder rod, seals, hose connections, hydraulic fluid condition, fitting leaks, mounting pins, sensor wiring, connector condition, controller input status, and the mechanical load on the gate or arm.
Common symptoms may include hydraulic fluid leakage, drifting, uneven movement, travel faults, position feedback errors, failure to complete travel, or the operator stopping unexpectedly. Similar symptoms can also come from bad hoses, contaminated fluid, incorrect hydraulic pressure, worn valves, air in the hydraulic system, a damaged sensor lead, or mechanical binding.
Before Ordering, Confirm
- The existing cylinder or parts diagram lists MX002219.
- The operator model and serial number have been checked.
- The cylinder size is 2.5 x 14 inch.
- The application requires a position-sensing cylinder, not a non-sensing cylinder.
- The mounting pin size, rod end, cylinder ends, and installed orientation match the original part.
- The hose ports, fittings, and hose routing match the existing installation.
- The sensor wiring and connector style match the operator control system.
- The package contents include the components needed for the repair, or related parts are being ordered separately.
- The problem is not caused by hydraulic hoses, valves, fluid contamination, pressure settings, sensor wiring, or mechanical binding.
- The current HySecurity parts diagram confirms MX002219 for the specific operator.
Installation and Service Notes
- Disconnect power and follow proper lockout procedures before servicing the operator.
- Relieve hydraulic pressure according to the operator service procedure before removing hoses or cylinder components.
- Support the gate, barrier arm, or lift mechanism before removing cylinder pins or hydraulic connections.
- Cap or protect hydraulic hoses and fittings to prevent contamination during service.
- Do not mix up hose routing, sensor wiring, or cylinder orientation during installation.
- After installation, check for leaks, smooth movement, correct travel, position feedback, and proper controller operation.
- Test all required safety devices and entrapment protection before returning the operator to service.
Professional Advisory
This is a hydraulic and position-sensing operator component. Service should be performed by a qualified gate technician when the repair involves hydraulic pressure, heavy gate or arm movement, cylinder pin removal, sensor wiring, controller position feedback, hydraulic leaks, unknown prior modifications, or an unsafe gate condition.
Do not bypass position feedback, limit functions, hydraulic controls, safety devices, entrapment protection, controller inputs, pressure controls, fuses, or operator protections to keep the system running. If the operator is drifting, binding, leaking, or stopping due to position feedback errors, the system should be inspected before continued operation.
Product Questions & Answers
What is the HySecurity MX002219 cylinder?
The HySecurity MX002219 is a 2.5 x 14 inch hydraulic position-sensing cylinder used in select HySecurity hydraulic operator applications where the parts diagram confirms this part number.
Is MX002219 a standard hydraulic cylinder?
No. MX002219 is a position-sensing hydraulic cylinder. It should not be replaced with a standard non-sensing cylinder unless HySecurity documentation specifically confirms that substitution.
What does the position-sensing feature do?
The position-sensing feature provides cylinder travel or position feedback to a compatible operator control system, helping the controller monitor movement where that function is required.
Which HySecurity operators use MX002219?
Public listings for MX002219 are not fully consistent, so the correct application should be verified by operator model, serial number, existing cylinder markings, and the current HySecurity parts diagram.
Can MX002219 replace MX002605?
Do not assume MX002219 and MX002605 are interchangeable. They are different part numbers, and the current HySecurity parts diagram should be checked before substituting any position-sensing cylinder.
What should I check before replacing this cylinder?
Check for hydraulic leaks, worn pins, damaged hoses, incorrect fittings, contaminated fluid, sensor wiring problems, controller input faults, and mechanical binding before replacing the cylinder.
Should a technician install this position-sensing cylinder?
Yes, this type of hydraulic and sensor-related repair should be handled by a qualified gate technician, especially when hydraulic pressure, heavy moving equipment, position feedback, or safety devices are involved.
