HySecurity MX5229-03, PUMP PACK,HW,TWIN,1.6 GPM,60HZ
The HySecurity MX5229-03 is a 1.6 GPM, 60Hz twin pump pack for select HySecurity / Nice HySecurity HydraWedge hydraulic barrier applications. The listed description is PUMP PACK, HW, TWIN, 1.6 GPM, 60HZ, which indicates a HydraWedge-related twin hydraulic pump pack configuration.
This pump pack should be matched carefully before ordering. Hydraulic pump packs are configuration-specific parts, and a similar-looking assembly may have a different flow rate, motor frequency, voltage, phase, reservoir layout, manifold connection, hose routing, or fitting arrangement.
What This Twin Pump Pack Does
The pump pack provides hydraulic flow for the compatible HydraWedge system. In a properly configured wedge barrier, the pump pack works with the hydraulic manifold, cylinder or cylinders, hoses, fittings, valves, reservoir, fluid, and controller to raise and lower the wedge safely and consistently.
The Twin designation is important because it points to a twin pump pack or twin hydraulic configuration. This should not be substituted with a single pump pack or a different flow-rate pump pack unless HySecurity documentation specifically confirms the replacement.
Compatible With
This pump pack may be used with the following applications where the current HySecurity parts diagram confirms MX5229-03:
- Select HySecurity HydraWedge hydraulic barrier applications requiring a twin pump pack
- HydraWedge systems where the original pump pack is marked, listed, or cross-referenced as MX5229-03
- Hydraulic wedge operator applications requiring a 1.6 GPM pump pack rated for 60Hz operation
- Applications where the hydraulic manifold, hose routing, fittings, motor configuration, and reservoir layout match the original MX5229-03 setup
- Repairs where the current HySecurity parts diagram specifically lists MX5229-03 for the pump pack location
Important: Do not assume this pump pack fits every HydraWedge, wedge, bollard, slide, swing, or barrier operator. Confirm the specific HydraWedge model, serial number, hydraulic circuit, and current parts diagram before ordering.
Similar Parts That Are Not Interchangeable
HySecurity pump packs can look similar but may not be interchangeable. Flow rate, frequency, voltage, phase, pump layout, hydraulic porting, manifold connection, hose routing, and fluid type all matter.
| Part / Pump Pack Type | Common Description | Interchangeability Note |
| MX5229-03 | HydraWedge twin pump pack, 1.6 GPM, 60Hz | Correct where MX5229-03 is listed by the current HySecurity parts diagram |
| Single pump pack | Pump pack for a single hydraulic circuit or different wedge configuration | Not a substitute for a twin pump pack unless HySecurity documentation confirms compatibility |
| Different GPM pump pack | Pump pack with a higher or lower hydraulic flow rating | May change wedge speed, hydraulic pressure behavior, and system performance |
| 50Hz pump pack | Pump pack configured for 50Hz power | Not the same as a 60Hz pump pack unless the motor and operator configuration confirm compatibility |
| Pump packs for other HySecurity operators | Pump packs used on StrongArm, HydraSwing, SwingRiser, or other hydraulic systems | Not interchangeable unless the same part number is listed by HySecurity |
Not Intended For
- HydraWedge applications that require a different pump pack flow rate
- HydraWedge applications that require a 50Hz pump pack or different electrical configuration
- Single-pump hydraulic systems unless the current parts diagram specifically lists MX5229-03
- StrongArm, StrongArmPark, HydraSwing, SwingRiser, SlideDriver, SlideSmart, SwingSmart, or bollard applications unless HySecurity documentation specifically lists MX5229-03
- Generic hydraulic pump replacement outside confirmed HySecurity HydraWedge twin applications
- Repairs where the issue is caused by valves, hoses, fittings, cylinder damage, fluid contamination, pressure settings, controller faults, or wedge binding instead of the pump pack
- Bypassing hydraulic controls, pressure controls, controller protections, vehicle detection, or safety devices
Important Compatibility Warning
The MX5229-03 pump pack is a 1.6 GPM, 60Hz twin pump pack. Do not select this part based only on the HydraWedge name or a visual match. The operator model, serial number, hydraulic circuit, electrical configuration, pump flow rating, motor frequency, hose routing, manifold layout, and fittings must match.
If the wedge is moving slowly, unevenly, or not at all, the pump pack may not be the only issue. Similar symptoms can be caused by low hydraulic fluid, air in the system, contaminated fluid, restricted hoses, leaking fittings, cylinder bypass, valve problems, incorrect pressure settings, controller faults, or a wedge that is mechanically binding.
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX5229-03 |
| Product Type | Hydraulic pump pack |
| Common Description | Pump Pack, HW, Twin, 1.6 GPM, 60Hz |
| Flow Rate | 1.6 GPM |
| Frequency | 60Hz |
| Configuration | Twin hydraulic pump pack configuration |
| Common Operator Family | Select HySecurity HydraWedge applications where specified |
| Hydraulic Considerations | Fluid type, reservoir, manifold, valves, hose routing, fittings, cylinders, pressure settings, and wedge movement must be verified during service |
| Package Contents | Pump pack assembly; confirm included motor, reservoir, couplers, fittings, hoses, seals, and mounting hardware before ordering |
Also Known As / Related Part Numbers
- MX5229-03
- MX522903
- MX-5229-03
- HySecurity MX5229-03
- Nice HySecurity MX5229-03
- HYS-MX5229-03
- HYS MX5229-03
- HySecurity Pump Pack, HW, Twin, 1.6 GPM, 60Hz
- HySecurity HydraWedge Twin Pump Pack
- HydraWedge 1.6 GPM 60Hz Twin Pump Pack
- HydraWedge Twin Hydraulic Pump Pack
- HW Twin Pump Pack 1.6 GPM 60Hz
Related Parts and Accessories
- HydraWedge hydraulic manifold components where valve control or pressure behavior is the issue
- HydraWedge hydraulic cylinders where cylinder bypass, leakage, or uneven movement is present
- Hydraulic hoses and fittings matched to the specific HydraWedge pump pack and manifold layout
- Hydraulic reservoir, seals, and approved hydraulic fluid where contamination or low fluid level is present
- Pressure relief, flow control, or directional valve components where the current parts diagram lists them separately
- Electrical motor, contactor, relay, fuse, or controller components where the pump does not start or receives incorrect power
- Vehicle detection, safety devices, and controller input components where wedge operation remains unsafe or inconsistent
Technician Note
Before replacing the MX5229-03 pump pack, inspect the full HydraWedge hydraulic system. A slow or weak wedge can be caused by low fluid, contaminated fluid, air in the lines, hose restriction, a leaking fitting, cylinder bypass, valve contamination, incorrect pressure, electrical motor issues, or mechanical binding in the wedge frame.
Also confirm the electrical side. This pump pack is listed as 60Hz, but the motor voltage, phase, wiring, overload protection, contactor, fuses, and controller output should still be checked against the operator wiring diagram before replacement. Do not assume the pump pack has failed until the hydraulic and electrical causes have been separated.
Before Ordering, Confirm
- The original or required part number is MX5229-03.
- The operator is a compatible HySecurity HydraWedge application.
- The current HySecurity parts diagram lists MX5229-03 for the pump pack position.
- The system requires a twin pump pack configuration.
- The required pump pack flow rate is 1.6 GPM.
- The required motor frequency is 60Hz.
- The motor voltage, phase, wiring, contactor, overload protection, and controller output match the original operator configuration.
- The hydraulic manifold, hoses, fittings, reservoir, cylinders, and fluid type match the existing system.
- The issue is not caused by valves, low fluid, contaminated fluid, air in the system, hose restriction, cylinder bypass, pressure settings, electrical faults, or wedge binding.
- The package contents include the components needed for the repair, or related parts are being ordered separately.
Installation and Service Notes
- Disconnect and lock out power before servicing the pump pack or operator wiring.
- Relieve hydraulic pressure according to the operator service procedure before removing hoses, fittings, valves, or pump pack components.
- Mark all hydraulic hoses and ports before disassembly to prevent crossed lines during installation.
- Cap or protect open hydraulic ports and hoses to prevent dirt, water, or debris from entering the hydraulic system.
- Verify motor voltage, phase, frequency, grounding, overload protection, and rotation where applicable before startup.
- Use only the correct hydraulic fluid, seals, fittings, and hose routing for the specific HydraWedge configuration.
- After installation, check for leaks, proper pump operation, smooth wedge movement, correct pressure behavior, and full cycle operation.
- Test all required safety devices, vehicle detection, access-control inputs, and operator protections before returning the wedge to service.
Professional Advisory
The MX5229-03 is a hydraulic pump pack used in a heavy HydraWedge barrier system. Service should be performed by a qualified gate technician when the repair involves hydraulic pressure, pump pack replacement, motor wiring, pressure diagnosis, valve troubleshooting, cylinder movement, heavy wedge motion, or unknown prior modifications.
Do not bypass hydraulic controls, relief valves, pressure controls, controller protections, fuses, disconnects, vehicle detection, safety devices, or operator safeguards to keep the wedge operating. If the wedge lowers unpredictably, fails to hold position, binds, leaks, or cannot be controlled safely, the system should be inspected before continued use.
Product Questions & Answers
What is the HySecurity MX5229-03?
The HySecurity MX5229-03 is a 1.6 GPM, 60Hz twin pump pack used on select HySecurity HydraWedge hydraulic barrier applications where the parts diagram confirms this part number.
What does HW Twin mean in the MX5229-03 description?
HW commonly points to HydraWedge, and Twin indicates a twin hydraulic pump pack configuration. The exact operator model and hydraulic diagram should still be verified before ordering.
Is MX5229-03 a 60Hz pump pack?
Yes. MX5229-03 is listed as a 60Hz pump pack. The motor voltage, phase, wiring, and controller configuration should still be confirmed against the operator wiring diagram.
Can MX5229-03 replace a single pump pack?
Do not assume it can. MX5229-03 is listed as a twin pump pack, and single-pump systems may use a different hydraulic layout, flow rate, porting, and motor configuration.
What should be checked before replacing this pump pack?
Check hydraulic fluid level, fluid condition, hose restrictions, fittings, cylinders, manifold valves, pressure settings, motor power, contactor operation, controller output, and wedge binding before replacing the pump pack.
Does MX5229-03 include the motor, fittings, or hoses?
The part is identified as a pump pack assembly. Package contents should be confirmed before ordering, especially if the repair also requires a motor, couplers, reservoir, fittings, hoses, seals, or mounting hardware.
Should a technician install the MX5229-03 pump pack?
Yes. This repair involves hydraulic pressure, electrical motor verification, twin pump pack configuration, and heavy wedge movement, so it should be handled by a qualified gate technician.
