NICE / APOLLO A2046, FRONT COVER HOUSING KIT FOR 816 ACTUATORS - INCLUDES BUSHING
The Nice Apollo A2046 is the front gear cover housing kit used on compatible Apollo 416 and 816 actuator repairs. The front housing is more than just an outside cover; it helps support the gear area and bushing point at the front of the actuator where internal movement is transferred through the linear arm assembly. When this part is damaged, the actuator may develop looseness, uneven movement, gear noise, water intrusion, or accelerated wear around the front-drive section. A2046 includes the bushing, which is important because a worn cover without proper bushing support can let the drive components run out of alignment. This kit should be matched to the actuator family and not confused with A2011 gear housing references, rear housing kits, A2024K cover tube kits, or internal screw and bearing service parts.
Compatible With
- Nice Apollo 416 actuator service applications
- Nice Apollo 416X actuator service applications when the front housing style matches
- Nice Apollo 816 actuator service applications
- Nice Apollo 816X actuator service applications when the front housing style matches
- Apollo 1500 / 1550 / 1600 / 1650 swing gate systems using compatible 416 or 816 actuator arms
- Verify by actuator diagram for older, newer, SMART, and X-series variations
Features & Specifications
| Manufacturer | Nice Apollo |
|---|
| Product Type | Front gear cover housing kit |
|---|
| Part Number | A2046 |
|---|
| Application | Front housing and bushing repair for compatible Apollo actuators |
|---|
| Compatible Operator Type | Swing gate actuator arms |
|---|
| Included Components | Front gear cover housing with bushing |
|---|
| Notes | Verify front housing style, not just actuator brand |
|---|
Also Known As / Related Part Numbers
- A2046
- NICE-A2046
- Apollo A2046
- Nice Apollo A2046
- Front cover housing kit
- Front gear cover with bushing
- Cover front gear w/bushing
- Gear housing cover with bushing
- Related search: HYS-A2046
Technician Note
For Apollo actuator parts, do not order by appearance only. Small differences in actuator generation, cable length, SMART feedback, limit style, connector layout, or internal hardware can make similar parts non-interchangeable. Compare the original part number, actuator model label, and exploded parts diagram before replacing the component.
Before Ordering Checklist
- Confirm the actuator model and operator series on the installed gate system.
- Match the original part number or the manufacturer parts diagram whenever possible.
- Check whether the repair involves a standard 816 actuator, 816X SMART actuator, 416 actuator, or another Apollo arm.
- Inspect related wear parts before replacing only one component.
- For electrical parts, disconnect power and have unsafe wiring or high-current diagnosis handled by a qualified gate technician.
Professional Advisory
Gate actuators are moving mechanical assemblies tied to control-board logic and required safety devices. After replacing internal actuator, harness, motor, sensor, or limit parts, the gate should be tested through full open and close cycles with proper force settings, limit settings, entrapment protection, and safety accessories in place. Do not bypass safety devices to make a repaired gate run.
Product Questions & Answers
What part of the actuator does A2046 repair?
A2046 repairs the front gear cover housing area of compatible Apollo 416 and 816 actuators and includes the bushing for that front housing location.
Is A2046 used on both 416 and 816 actuators?
Yes, common references list A2046 for 416 or 816 actuators, but the installed actuator style and generation should still be verified.
Can a worn front housing affect gate movement?
Yes. Excessive wear or a damaged bushing area can allow looseness, noise, misalignment, or added strain on the internal drive components.
Is this the same as a rear housing kit?
No. A2046 is the front gear cover housing kit. Rear housing kits, cover tubes, bearing kits, and limit assemblies are different Apollo service parts.
What should be checked before ordering?
Check the actuator model, front housing shape, bushing wear, related gear or screw damage, and whether the actuator has other internal wear before replacing only the cover.
