NICE / APOLLO A2086, MAIN SCREW KIT - INCLUDES LIMIT SCREW, BUSHINGS/BEARINGS AND NUT
The Nice Apollo A2086 main screw kit is used to service the internal screw-drive area of compatible Apollo 416 and 816 swing gate actuators. Inside a linear actuator, the screw and related bearings/bushings convert motor rotation into push-pull movement of the actuator arm. Wear in this area can show up as grinding, binding, uneven travel, excessive backlash, failed travel adjustment, or a gate that strains even though the hinges and brackets appear normal. A2086 is useful when the repair requires more than just a single screw or bearing, because it includes the limit screw, bushing/bearing components, and nut as a kit. This part should be matched by actuator model and internal assembly style before ordering, especially on older 416/816, X-series, or SMART-generation actuators.
Compatible With
- Nice Apollo 416 actuator service applications
- Nice Apollo 416X actuator service applications when internal screw assembly matches
- Nice Apollo 816 actuator service applications
- Nice Apollo 816X actuator service applications when internal screw assembly matches
- Apollo 1500 / 1550 / 1600 / 1650 swing gate systems using compatible 416 or 816 actuators
- Verify by parts diagram for actuator generation and internal screw assembly
Features & Specifications
| Manufacturer | Nice Apollo |
|---|
| Product Type | Main screw kit |
|---|
| Part Number | A2086 |
|---|
| Application | Internal screw-drive repair for compatible Apollo actuators |
|---|
| Compatible Operator Type | Swing gate actuator arms |
|---|
| Included Components | Limit screw, bushing/bearings, and nut as commonly listed |
|---|
| Notes | Inspect related bearings, extension tube, and limit components during repair |
|---|
Also Known As / Related Part Numbers
- A2086
- NICE-A2086
- Apollo A2086
- Nice Apollo A2086
- Main screw kit
- Screw drive repair kit
- Limit screw, bushing/bearing and nut kit
- Related individual parts: A2018 main screw, A2019 limit screw
- HYS-A2086
Technician Note
For Apollo actuator parts, do not order by appearance only. Small differences in actuator generation, cable length, SMART feedback, limit style, connector layout, or internal hardware can make similar parts non-interchangeable. Compare the original part number, actuator model label, and exploded parts diagram before replacing the component.
Before Ordering Checklist
- Confirm the actuator model and operator series on the installed gate system.
- Match the original part number or the manufacturer parts diagram whenever possible.
- Check whether the repair involves a standard 816 actuator, 816X SMART actuator, 416 actuator, or another Apollo arm.
- Inspect related wear parts before replacing only one component.
- For electrical parts, disconnect power and have unsafe wiring or high-current diagnosis handled by a qualified gate technician.
Professional Advisory
Gate actuators are moving mechanical assemblies tied to control-board logic and required safety devices. After replacing internal actuator, harness, motor, sensor, or limit parts, the gate should be tested through full open and close cycles with proper force settings, limit settings, entrapment protection, and safety accessories in place. Do not bypass safety devices to make a repaired gate run.
Product Questions & Answers
What is included with A2086?
Common listings describe A2086 as a main screw kit that includes the limit screw, bushing/bearing components, and nut.
Is A2086 the same as A2018?
No. A2018 is commonly listed as an individual main screw, while A2086 is a kit with related screw-drive components.
What symptoms can point to main screw wear?
Binding, grinding, uneven travel, excessive play, repeated limit problems, or actuator strain can point to screw-drive wear, but gate hinge drag should be checked too.
Does this fit both 416 and 816 actuators?
Common references support 416 and 816 actuator applications, but the exact actuator generation and internal parts diagram should be confirmed.
Should this be installed by a technician?
Yes, this is an internal actuator repair. A qualified gate technician should handle the repair if there is wiring damage, unsafe movement, or uncertainty about limit adjustment.
