NICE / APOLLO SPMTG07600, Electric motor kit forM3BAR/M5BAR
The NICE Apollo SPMTG07600 is a replacement electric motor kit for select Nice M3BAR and M5BAR barrier arm operators. The motor kit is a key service component in the barrier drive system, supplying the power needed to raise and lower the arm through the internal mechanical assembly. When the original motor kit is failing, the barrier may move unevenly, struggle near the end of travel, stop under load, produce excessive noise, or fail to move the arm even though the controller is sending commands.
This kit is intended for the smaller and mid-size M-Bar family applications commonly identified as M3BAR and M5BAR. It should not be selected only by appearance, because M7BAR and LBAR operators may require different motor groups. Before ordering, confirm the operator model tag, the original part number, and whether the cabinet is an R10 or other service generation. A motor failure should also prompt inspection of the arm length, spring balance, mounting hardware, and release system so the replacement motor is not installed into an overloaded mechanism.
Compatible With
- Nice M3BAR barrier operators when the service diagram lists SPMTG07600
- Nice M5BAR barrier operators when the service diagram lists SPMTG07600
- M3BAR R10 and M5BAR R10 applications where the original motor kit reference matches
- Select Nice M-Bar barrier operator motor-service applications, confirmed by parts diagram
- Not for M7BAR SPMTG02900 applications or LBAR SPMTG10700A applications unless the parts diagram clearly supersedes the number
Features & Specifications
| Specification | Details |
|---|
| Manufacturer | NICE / Apollo |
| Product Type | Electric motor kit |
| Part Number | SPMTG07600 |
| Application | Replacement motor kit for select M3BAR/M5BAR barrier operators |
| Compatible Operator Type | Nice M-Bar barrier arm operator |
| Notes | Confirm exact model, R10 generation, and motor kit reference |
Also Known As / Related Part Numbers
- SPMTG07600
- Nice SPMTG07600
- NICE-SPMTG07600
- Electric motor kit for M3BAR
- Electric motor kit for M5BAR
- M3BAR/M5BAR motor kit
- MBar R10 motor kit
Technician Note
Do not install a new motor kit until the barrier arm is checked for proper balance. A stiff hinge point, wrong arm length, damaged spring assembly, or physical obstruction can make a good motor act like it is bad.
Before Ordering
- Confirm the operator is an M3BAR or M5BAR application using SPMTG07600
- Compare the removed motor kit to the new kit before installation
- Check spring balance and arm length against the barrier setup
- Inspect the control board and limit settings if the arm stops in the wrong place
- Do not use this kit as a substitute for M7BAR or LBAR motor groups without confirmation
Professional Advisory
Barrier operator motor replacement should be handled by qualified personnel when internal wiring or spring-loaded mechanical parts are involved. Do not defeat limits, safety inputs, or covers to make the operator run.
Product Questions & Answers
Which operators commonly use SPMTG07600?
SPMTG07600 is commonly listed as an electric motor kit for Nice M3BAR and M5BAR barrier operator applications.
Is SPMTG07600 the same as SPMTG02900?
No. SPMTG02900 is commonly associated with M7BAR motor assembly applications, while SPMTG07600 is commonly associated with M3BAR/M5BAR motor kit applications.
Can a control-board problem look like a bad motor?
Yes. A failed relay, incorrect setup, safety input, limit issue, or power problem can prevent the motor from running. Diagnose before replacing the motor kit.
What should I compare on the old motor?
Compare the part number, mounting, harness, connector, gear arrangement, and overall motor kit layout.
Will this repair a broken barrier arm?
No. This is the motor kit. Damaged arms, springs, brackets, cabinets, or control boards must be repaired with the proper separate parts.
