Transmitter Solutions RFMOD418 HIVE Receiver Module Compatibility Details
The Transmitter Solutions RFMOD418 is a 418 MHz plug-in radio frequency module used with the compatible RECTSMULFRE HIVE dual-frequency Wiegand receiver platform. The HIVE receiver processor uses removable radio frequency cards so a receiver can be configured for supported radio frequencies without treating every frequency as a separate complete receiver assembly.
The manufacturer HIVE receiver manual specifically identifies a 418 MHz receiving card and states that the 418 MHz card can be installed in either receiver card connector C1 or C2. RFMOD418 should not be ordered as a complete standalone gate receiver, relay receiver, or universal 418 MHz radio interface.
What the RFMOD418 Module Does
RFMOD418 provides the 418 MHz radio receiving function for the compatible HIVE receiver processor system. The host receiver processes the received transmitter data and can provide a 3-wire RF bus output and/or Wiegand output to the connected access control or receiver system.
The receiver processor board uses plug-in RF cards to select the required receiving frequency. This modular design allows the HIVE platform to accommodate two supported frequency cards when the processor board, radio modules, antenna arrangement, and transmitter protocols are correctly matched.
All Verified Receiver Compatibility
- Transmitter Solutions RECTSMULFRE HIVE Wiegand Dual Band Receiver
The current Transmitter Solutions product information identifies the RECTSMULFRE as a dual-frequency receiver with two frequency card slots. The applicable HIVE receiver manual specifically documents the 418 MHz receiving card and its installation positions on the receiver processor board.
Verified 418 MHz Receiver Card Slot Compatibility
- C1 receiver card connector - documented for 318 MHz and 418 MHz cards
- C2 receiver card connector - documented for 295 MHz, 318 MHz, and 418 MHz cards
The HIVE manual specifically states that the 418 MHz receiving card can be inserted in either the right C1 connector or the left C2 connector. Verify the physical board labels and processor generation before service because frequency support and migration configurations should be matched to the actual receiver hardware.
Related Manufacturer-Documented 418 MHz Elite Compatible Transmitters
Transmitter Solutions currently lists the following models in its 418 MHz transmitter family and identifies each model as compatible with the Elite DT-418 system:
- Transmitter Solutions Monarch 418ELPW1K-C - one-button key chain transmitter
- Transmitter Solutions Monarch 418ELPW2K-C - two-button key chain transmitter
- Transmitter Solutions Stingray 418ELPW1V - one-button visor transmitter
- Transmitter Solutions Stingray 418ELPW2V - two-button visor transmitter
The public RFMOD418 documentation does not directly list these four transmitter part numbers as guaranteed RFMOD418 pairings. Confirm the existing receiver programming, transmitter protocol, credential data, and application before ordering replacement or additional remotes. Matching 418 MHz frequency alone is not enough to prove compatibility.
Wiegand and RF Bus Compatibility
The compatible HIVE receiver processor provides Wiegand DATA1 and DATA0 outputs and allows the Wiegand output to be selected for 26-bit or 30-bit operation through the processor board configuration. The receiver also provides a 3-wire RF bus connection.
RFMOD418 is the radio receiving card. It does not independently provide a standalone relay output or convert an incompatible transmitter into a Wiegand credential. The receiver processor and connected access control system must support the selected data format and credential configuration.
418 MHz to 433 MHz Migration Considerations
The current RECTSMULFRE product information describes the receiver platform as supporting 295 MHz, 318 MHz, and 418 MHz with migration to 433 MHz. This does not mean a 418 MHz transmitter will operate through a 433 MHz RF module.
RFMOD418 and a 433 MHz radio card are different frequency modules. Existing 418 MHz transmitters should not be assumed compatible with a 433 MHz module, and 433 MHz remotes should not be assumed compatible with RFMOD418. The transmitter frequency and radio protocol must match the installed receiver configuration.
Similar RF Modules Are Not Automatically Interchangeable
Do not substitute a 295 MHz, 318 MHz, or 433 MHz receiver card for RFMOD418 when the installation requires 418 MHz reception. Frequency card selection changes the radio frequency received by the HIVE processor.
Likewise, a standalone 418 MHz receiver is not automatically a direct replacement for RFMOD418. A separate receiver may use a relay output, different credential format, different programming method, different antenna connection, or a different radio protocol. Verify the complete receiver architecture before replacing only the RF card.
Features and Specifications
| Feature | Specification |
| Brand | Transmitter Solutions |
| Part Number | RFMOD418 |
| Product Type | Plug-in radio frequency receiver module |
| Radio Frequency | 418 MHz |
| Verified Host Receiver | RECTSMULFRE HIVE Wiegand Dual Band Receiver |
| 418 MHz Card Position | C1 or C2 receiver card connector |
| Host Receiver Card Capacity | 2 frequency card slots |
| Host Receiver Wiegand Output | Selectable 26-bit or 30-bit |
| Host Receiver Data Connections | Wiegand DATA0 and DATA1; 3-wire RF bus |
| Host Receiver Input Power | 12-24 VAC/DC |
| Host Receiver Power Consumption | 24 mA |
| Host Receiver Maximum Output Current | 250 mA |
| Host Receiver Output Type | Wiegand |
| Standalone Receiver | No - requires the compatible HIVE receiver processor system |
| Standalone Relay Output | No standalone relay output provided by the RF module |
Package Contents and Items Not Included
RFMOD418 is identified as a 418 MHz RF module for the multi-frequency receiver system. The manufacturer receiver documentation describes the plug-in 418 MHz radio card but does not provide a separate public retail package-content list for RFMOD418.
Do not assume the RECTSMULFRE processor board, outdoor receiver enclosure, antenna accessories, transmitters, access control panel, wiring, or a second RF module are included unless specifically stated with the item being purchased. Confirm package contents when building a complete receiver system.
Technician Note
The important detail on this module is not just 418 MHz. First verify that the existing receiver is a RECTSMULFRE HIVE processor and then identify the transmitter system being retained. The manufacturer manual allows the 418 MHz card in either C1 or C2, but a random 418 MHz remote should not be assumed compatible just because the frequency number matches.
Before Ordering Checklist
- Verify the receiver model is Transmitter Solutions RECTSMULFRE.
- Check the physical HIVE processor board and board labels.
- Verify the existing RF module part number and frequency.
- Confirm that 418 MHz reception is required.
- Identify the existing transmitter manufacturer, model, and radio protocol.
- Check the installed RF cards in C1 and C2.
- Confirm the required 26-bit or 30-bit Wiegand receiver configuration.
- Verify whether an antenna or antenna coax accessory is required for the installation.
- Confirm package contents if a complete receiver assembly is needed.
Installation and Service Notes
The HIVE receiver manual states that the radio frequency card ports are supplied with jumper strips and that these strips should only be replaced by the proper radio cards. The 418 MHz receiving card is documented for either C1 or C2. Follow the applicable receiver documentation and verify the card position, antenna terminals, and processor configuration before returning the system to service.
For damaged receiver boards, unknown access control wiring, power faults, or unclear Wiegand communication problems, use a qualified gate or access control technician. Do not bypass gate safety circuits or entrapment protection while diagnosing a receiver or access control problem.
Product Questions and Answers
Is the Transmitter Solutions RFMOD418 a complete receiver?
No. RFMOD418 is a 418 MHz plug-in radio frequency module for the compatible RECTSMULFRE HIVE receiver processor system. It is not a complete standalone relay receiver.
Which receiver is verified for the RFMOD418 module?
The verified host receiver is the Transmitter Solutions RECTSMULFRE HIVE Wiegand Dual Band Receiver. Verify the physical processor board and installed frequency cards before ordering the module.
Can the 418 MHz RF card be installed in either HIVE receiver slot?
Yes. The Transmitter Solutions HIVE receiver manual specifically states that the 418 MHz receiving card can be inserted in either the right C1 connector or the left C2 connector.
Will any 418 MHz gate remote work with RFMOD418?
No. Matching the 418 MHz frequency alone does not prove radio protocol or credential compatibility. Verify the exact transmitter model and existing receiver system before ordering additional remotes.
Which current Transmitter Solutions 418 MHz transmitters are documented for the Elite DT-418 system?
Transmitter Solutions lists the Monarch 418ELPW1K-C, Monarch 418ELPW2K-C, Stingray 418ELPW1V, and Stingray 418ELPW2V as 418 MHz transmitters compatible with Elite DT-418. Confirm the RFMOD418 receiver application before treating an individual transmitter as a guaranteed pairing.
Can RFMOD418 be replaced with the RFMOD433 module during a frequency migration?
Do not treat the 418 MHz and 433 MHz RF modules as automatically interchangeable for existing remotes. A 418 MHz transmitter will not be made into a 433 MHz transmitter by changing the receiver card. Verify the transmitter migration plan and receiver configuration first.
Does RFMOD418 provide a relay output directly to the gate operator?
No standalone relay output is documented for the RF module. The compatible HIVE receiver processor handles the radio data and provides its configured Wiegand and/or 3-wire RF bus connection to the connected system.
What should I check before ordering Transmitter Solutions RFMOD418?
Verify the RECTSMULFRE receiver model, processor board, installed RF cards, C1 and C2 slot configuration, required 418 MHz transmitter protocol, Wiegand format, antenna requirements, and package contents. Do not order by frequency alone.
