HySecurity MX000143, MANIFOLD ASSY, BRAKE, SLIDEDRIVER
The HySecurity MX000143 is a replacement braking manifold assembly / brake kit for select HySecurity and Nice HySecurity SlideDriver hydraulic gate operators. It is commonly listed as MANIFOLD ASSY, BRAKE, SLIDEDRIVER and as a brake kit for SlideDriver 50VF, SlideDriver 80, and SlideDriver 200 applications.
This assembly is part of the hydraulic braking system used in compatible SlideDriver pump pack configurations. The braking manifold and valves help control hydraulic stopping behavior so the gate can stop more predictably instead of coasting, overrunning, or stopping harshly. In a properly adjusted system, the brake kit works together with the pump pack, hydraulic motor, drive wheels, hoses, valves, limits, and controller to manage gate movement.
Current listings commonly describe MX000143 as including the brake manifold, brake valves, quick disconnect sockets, and seal kit. HySecurity parts documentation lists MX000143 for select SlideDriver 50VF2/3, 80, and 200 models, while MX000137 is used for different SlideDriver 30F and 40 braking applications. Always verify the exact operator model and parts diagram before ordering.
What This Braking Manifold Assembly Does
The MX000143 braking manifold assembly helps control hydraulic braking in compatible SlideDriver operators. When the operator slows or stops the gate, the braking manifold and valves help manage hydraulic flow so the gate stops in a controlled manner.
If the braking manifold, brake valves, seals, or quick disconnects are damaged, leaking, contaminated, stuck, or incorrectly matched to the operator, the gate may coast past its stop point, stop too abruptly, stop inconsistently, leak hydraulic fluid, or show poor stopping control. These symptoms can also be caused by incorrect brake adjustment, contaminated hydraulic fluid, worn drive wheels, gate drag, limit setup issues, hydraulic motor problems, hose leaks, or pump pack wear.
Compatible With
The HySecurity MX000143 is intended for select HySecurity / Nice HySecurity SlideDriver hydraulic operators where this braking manifold assembly / brake kit is specified. Compatibility depends on the operator model, serial number, pump pack style, braking manifold layout, valve configuration, hose routing, quick disconnects, and current HySecurity parts documentation.
- Select HySecurity SlideDriver 50VF applications where MX000143 is listed as the brake kit
- Select HySecurity SlideDriver 50VF2/3 applications where MX000143 is listed as the brake kit
- Select HySecurity SlideDriver 80 applications where MX000143 is listed as the brake kit
- Select HySecurity SlideDriver 200 applications where MX000143 is listed as the brake kit
- Select SlideDriver pump pack applications using the matching braking manifold and valve layout
- Operator repairs where the original braking manifold assembly is marked, listed, or cross-referenced as MX000143
Do not assume MX000143 fits every HySecurity SlideDriver, SlideDriver II, SlideSmart, SwingSmart, StrongArm, HydraSwing, HydraLift, HydraWedge, barrier arm, Smart DC, Smart Touch, or SmartCNX operator. Similar hydraulic operators may use different brake kits, manifold layouts, valve sizes, pump pack assemblies, hose kits, and quick disconnect configurations.
MX000143 and MX000137 are both HySecurity SlideDriver brake kit references, but they are not interchangeable without checking the operator parts diagram.
- MX000143: Commonly listed as the brake kit / braking manifold assembly for select SlideDriver 50VF2/3, 80, and 200 applications.
- MX000137: Commonly listed as the brake kit / braking manifold assembly for select SlideDriver 30F and 40 applications.
Before ordering, compare the operator model, pump pack, valve layout, quick disconnect size, and parts diagram. A brake kit that fits one SlideDriver hydraulic family may not match another.
MX000143 and Soft-Start Parts
MX000143 should also be kept separate from the soft-start AWOG components used in some SlideDriver hydraulic systems.
- MX000143: Braking manifold assembly / brake kit for select larger SlideDriver hydraulic applications.
- MX001276: Face down AWOG soft-start manifold kit.
- MX000618: Face down AWOG hose assembly / plugged AWOG assembly.
Braking and soft-start are related hydraulic behavior issues, but they are not the same repair. Harsh starting, poor stopping, coasting, and hydraulic leakage should be diagnosed by checking the full hydraulic system before selecting parts.
Not Intended For
- Universal HySecurity hydraulic brake kit replacement
- SlideDriver 30F or SlideDriver 40 applications that require MX000137
- Replacing the soft-start AWOG manifold kit MX001276
- Replacing the face down AWOG hose assembly MX000618
- Replacing standard hydraulic hose kits such as MX001129, MX4289, MX4323, MX4578, or MX001732
- Replacing the complete pump pack unless the pump pack is separately ordered
- Replacing hydraulic motors, valve coils, controller boards, drive wheels, limit assemblies, or safety devices unless those parts are separately specified
- Correcting poor stopping caused by gate drag, incorrect limits, worn drive wheels, contaminated hydraulic fluid, low fluid, hose leaks, or pump pack problems without addressing the cause
Important Compatibility Warning
MX000143 should be selected by HySecurity part number, operator model, and pump pack configuration. Do not order by the phrase brake manifold alone. HySecurity hydraulic operators may use different brake manifolds, valve arrangements, quick disconnects, seal kits, and pump pack layouts depending on the SlideDriver model and production generation.
If the operator is a SlideDriver 30F or 40, check whether MX000137 is the correct brake kit instead. If the complaint is harsh startup rather than poor stopping, check the soft-start / AWOG system before assuming the braking manifold is the failed component.
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX000143 |
| Product Type | Braking manifold assembly / hydraulic brake kit |
| Common Description | MANIFOLD ASSY, BRAKE, SLIDEDRIVER |
| Alternate Description | Brake Kit, SlideDriver 50VF / 80 / 200 |
| Common Applications | Select SlideDriver 50VF2/3, 80, and 200 applications where MX000143 is specified |
| Hydraulic System Area | Pump pack / braking manifold section of compatible SlideDriver hydraulic operators |
| Function | Helps control hydraulic braking and stopping behavior in compatible SlideDriver systems |
| Common Included Components | Current listings commonly reference brake manifold, brake valves, quick disconnect sockets, and seal kit; verify current package contents before publishing as guaranteed |
| Related Smaller Brake Kit | MX000137 is a related brake kit commonly listed for select SlideDriver 30F and 40 applications |
| Related Soft-Start Kit | MX001276 is a related face down AWOG soft-start manifold kit, not the same part |
| Not Included Unless Listed | Complete pump pack, hydraulic motor, standard hose kits, reservoir, hydraulic fluid, drive wheels, controller board, soft-start AWOG parts, valve coils outside the kit, and operator hardware unless separately listed |
Also Known As / Related Part Numbers
- MX000143
- HySecurity MX000143
- Nice HySecurity MX000143
- HySecurity MANIFOLD ASSY, BRAKE, SLIDEDRIVER
- HySecurity Braking Manifold Assembly
- HySecurity Brake Manifold Assembly
- HySecurity Brake Kit, SlideDriver
- HySecurity SlideDriver Brake Kit
- HySecurity SlideDriver 50VF Brake Kit
- HySecurity SlideDriver 50VF2/3 Brake Kit
- HySecurity SlideDriver 80 Brake Kit
- HySecurity SlideDriver 200 Brake Kit
- HySecurity hydraulic braking manifold
- HYS-MX000143, related distributor SKU format
- MX000137, related brake kit for select SlideDriver 30F and 40 applications
- MX001276, related face down AWOG soft-start manifold kit, not the same part
- MX000618, related face down AWOG hose assembly, not the same part
- MX000657, related brake valve reference in some HySecurity parts documentation
- MX000201, related 1/4 inch quick disconnect socket reference in some HySecurity pump pack parts documentation
- MX000202, related 1/4 inch quick disconnect plug reference in some HySecurity pump pack parts documentation
Related Parts and Accessories
- mx000137-braking-manifold-assembly-slidedriver.html">HySecurity MX000137 brake kit where the operator requires the 30F / 40 braking kit
- mx001276-face-down-awog-soft-start-manifold-kit.html">HySecurity MX001276 face down AWOG soft-start manifold kit where soft-start behavior is being serviced
- mx000618-face-down-awog-hose-assembly.html">HySecurity MX000618 face down AWOG hose assembly where the AWOG hose is the failed component
- HySecurity brake valves where valve replacement is being handled separately
- HySecurity quick disconnect sockets or plugs where the fitting is damaged or leaking
- HySecurity seal kit components where hydraulic leakage is at the braking manifold
- Hydraulic fluid specified by the current HySecurity operator manual
- Hydraulic hose kits matched to the operator model and pump pack style
- Drive wheel, hydraulic motor, and pump pack components where poor stopping is related to broader hydraulic wear
Technician Note
The MX000143 braking manifold assembly is used for stopping control in compatible SlideDriver hydraulic systems. If the gate is coasting, stopping too hard, or not stopping consistently, check the full braking and travel system before replacing parts. Limit setup, brake valve function, hydraulic fluid condition, drive wheel traction, pump pack condition, and gate movement all affect stopping behavior.
Do not confuse braking complaints with soft-start complaints. MX000143 is a braking manifold assembly. MX001276 and MX000618 are tied to the AWOG / soft-start system. A gate that jerks at startup may need a different diagnosis than a gate that coasts or stops poorly.
Before Ordering, Confirm
- Confirm the needed HySecurity part number is MX000143.
- Confirm the existing assembly is described as MANIFOLD ASSY, BRAKE, SLIDEDRIVER or Brake Kit, SlideDriver 50VF / 80 / 200.
- Confirm the operator model and serial number.
- Confirm whether the operator is a compatible SlideDriver 50VF2/3, 80, or 200 application listed by the parts diagram.
- Confirm the operator does not require MX000137 or another braking manifold kit instead.
- Confirm the pump pack, brake valve layout, quick disconnect sockets, and seal arrangement match the replacement kit.
- Confirm the stopping issue is not caused by limit settings, hydraulic fluid condition, gate drag, worn drive wheels, hose leaks, or pump pack damage.
- Confirm whether brake manifold, valves, quick disconnect sockets, seal kit, instructions, and hydraulic fluid are included or must be ordered separately.
Installation and Service Notes
Hydraulic braking manifold service should be done with the operator disabled, the gate secured, and the hydraulic system handled according to the current HySecurity service procedure. Keep dirt, water, metal shavings, and debris out of open hydraulic fittings. Contamination can damage valves, pump components, hydraulic motors, and seals.
After the braking manifold assembly is serviced, inspect for leaks and verify controlled stopping, proper gate travel, correct limit behavior, hydraulic pressure, and brake valve operation according to the current HySecurity manual. If the operator continues to coast, stop harshly, or behave inconsistently, continue diagnosing the pump pack, brake valves, limit system, hydraulic motor, drive wheels, and gate movement.
Professional Advisory
Hydraulic gate operator repair involves moving gate parts, pinch points, hydraulic fluid, pressure-rated components, and operator drive systems. A qualified HySecurity gate technician should handle braking manifold service if the hydraulic issue is unclear, the gate is heavy, the operator has repeated stopping problems, or the pump pack has been modified or previously repaired.
Do not bypass covers, guards, limits, monitored entrapment protection, photo eyes, safety edges, brake systems, or other safety devices during hydraulic service. The operator should be fully tested after repair to confirm controlled stopping, proper hydraulic operation, smooth travel, and working safety devices.
Product Questions & Answers
What is the HySecurity MX000143 used for?
The HySecurity MX000143 is a braking manifold assembly / brake kit used in select HySecurity SlideDriver hydraulic operators, most commonly SlideDriver 50VF2/3, 80, and 200 applications where the parts diagram lists this kit.
What is included with MX000143?
Current listings commonly describe MX000143 as including the brake manifold, brake valves, quick disconnect sockets, and seal kit. Verify current package contents before ordering if any component is required for the repair.
Does MX000143 fit SlideDriver 30F or 40?
MX000143 is commonly listed for SlideDriver 50VF2/3, 80, and 200. SlideDriver 30F and 40 applications commonly reference MX000137 instead. Always verify the operator parts diagram before ordering.
Is MX000143 the same as MX001276?
No. MX000143 is a braking manifold assembly / brake kit. MX001276 is a face down AWOG soft-start manifold kit. Braking and soft-start components are related to hydraulic behavior but are different parts.
Can MX000143 fix a gate that coasts past the stop point?
It may help if the braking manifold or brake valves are the failed components, but coasting can also be caused by incorrect brake adjustment, worn drive wheels, limit problems, gate drag, contaminated fluid, pump pack wear, or hydraulic motor issues.
Should I replace this braking manifold myself?
Braking manifold service should be handled by a qualified HySecurity gate technician if the hydraulic issue is unclear, the gate is heavy, the operator has repeated stopping problems, or the pump pack has been modified or previously repaired.
