Transmitter Solutions RECTSMULFRE1 Model 1 RF Slot and Wiegand Compatibility Details
The Transmitter Solutions RECTSMULFRE1 is a HIVE Model 1 multi-frequency receiver configuration with Wiegand output. The receiver processor uses two plug-in RF module slots so two supported transmitter systems can be received through one configurable receiver platform.
The RECTSMULFRE1 catalog configuration identifies 318 MHz DoorKing-compatible or 418 MHz for the left slot and 295 MHz, 318 MHz DoorKing-compatible, or 418 MHz for the right slot. Two RF modules are required and sold separately.
Current public Transmitter Solutions documentation identifies the broader receiver family as RECTSMULFRE*. The exact RECTSMULFRE1 suffix is not separately defined on the current public family page or legacy manual, so verify the physical receiver label when replacing an existing Model 1 receiver.
What the RECTSMULFRE1 Receiver Does
RECTSMULFRE1 receives compatible radio transmitter data through two separately installed RF modules. The HIVE processor then provides its configured Wiegand and/or 3-wire RF bus output to the connected access control equipment.
The dual-frequency architecture can be used to retain a supported existing transmitter system while adding another supported frequency and protocol. The processor has two RF module slots and is configured for two installed radio cards. It does not receive every HIVE frequency simultaneously.
Model 1 Left RF Slot Compatibility
The RECTSMULFRE1 Model 1 configuration identifies the following left-slot RF module options:
The applicable HIVE processor manual identifies the C1 receiver card connector for 318 MHz and 418 MHz cards. The manual also identifies the 318 MHz receiver application with DoorKing protocol.
Do not substitute RFMOD318-L for RFMOD318-D based only on the 318 MHz frequency. The "-D" and "-L" module suffixes identify different protocol applications.
Model 1 Right RF Slot Compatibility
The RECTSMULFRE1 Model 1 configuration identifies the following right-slot RF module options:
- RFMOD296 - 295 MHz RF module
- RFMOD318-D - 318 MHz DoorKing-compatible RF module
- RFMOD418 - 418 MHz RF module
The HIVE processor manual identifies the C2 receiver card connector for 295 MHz, 318 MHz, and 418 MHz cards. It documents the 295 MHz receiver application with Sentex protocol and the 318 MHz receiver application with DoorKing protocol.
RFMOD296 is used for the documented 295 MHz application. Do not interpret the "296" in the module SKU as a 296 MHz operating frequency.
Two RF Modules Are Required and Sold Separately
RECTSMULFRE1 requires two RF modules to complete the Model 1 dual-frequency receiver configuration. Select one supported module for the left slot and one supported module for the right slot.
The base receiver should not be assumed to include RFMOD296, RFMOD318-D, or RFMOD418. Verify that both required RF modules are included in the order.
Installing two cards that operate at the same frequency should not be assumed to increase receiver range, memory capacity, or transmitter compatibility. Select the modules according to the two radio systems actually used at the property.
RECTSMULFRE1 Model 1 RF Module Configuration
| Receiver Slot | RF Module | Frequency or Application |
| Left Slot | RFMOD318-D | 318 MHz DoorKing-compatible configuration |
| Left Slot | RFMOD418 | 418 MHz |
| Right Slot | RFMOD296 | 295 MHz Sentex protocol application |
| Right Slot | RFMOD318-D | 318 MHz DoorKing-compatible configuration |
| Right Slot | RFMOD418 | 418 MHz |
Verified Frequency and Protocol Applications
The applicable Transmitter Solutions HIVE manual documents the following receiver applications:
- 295 MHz with Sentex protocol
- 318 MHz with DoorKing protocol
- 418 MHz plug-in receiving card support
Frequency alone does not prove transmitter compatibility. Match the RF module, radio protocol, transmitter model, and facility code requirements before adding or replacing remotes.
Important 318 MHz DoorKing and Linear Module Difference
The RECTSMULFRE1 Model 1 configuration identifies RFMOD318-D for the 318 MHz application. The applicable HIVE documentation identifies the 318 MHz receiver configuration with DoorKing protocol.
RFMOD318-L is a separate Linear-compatible 318 MHz module designation. Both modules use 318 MHz, but the matching frequency does not make the radio protocols interchangeable. Check the module suffix and existing transmitter family before ordering.
295 MHz Sentex Application
The official HIVE manual identifies the 295 MHz receiver configuration with Sentex protocol. For the RECTSMULFRE1 Model 1 right slot, the catalog module identified for the 295 MHz application is RFMOD296.
Do not assume every 295 MHz transmitter is compatible. Verify the original Sentex transmitter application, transmitter part number, facility code, and existing receiver system.
418 MHz Module Compatibility
The HIVE manual documents 418 MHz receiving card support and specifically states that the 418 MHz card can be inserted in either documented receiver card connector C1 or C2. This matches the Model 1 configuration allowing RFMOD418 in either slot.
Matching 418 MHz frequency alone still does not prove compatibility with every 418 MHz transmitter. Identify the transmitter family and existing receiver application before ordering additional remotes.
Manufacturer-Documented Monarch and Stingray Accessory Families
The Transmitter Solutions HIVE Wiegand Dual Band receiver cut sheet lists the following transmitter accessory families:
- Monarch 295 MHz transmitters
- Monarch 318 MHz transmitters
- Monarch 433 MHz transmitters
- Stingray 295 MHz transmitters
- Stingray 318 MHz transmitters
- Stingray 433 MHz transmitters
The cut sheet does not provide an exact transmitter SKU matrix for every RECTSMULFRE1 module combination. Match the installed RF module, transmitter frequency, protocol, facility code, and transmitter family before ordering remotes.
26-Bit and 30-Bit Wiegand Output
The HIVE processor provides Wiegand DATA1 and DATA0 outputs. The manufacturer manual documents selectable 26-bit or 30-bit Wiegand output through the processor board DIP switch configuration.
- DIP2 ON - 30-bit Wiegand output
- DIP2 OFF - 26-bit Wiegand output
- DIP1 - controls the documented state of bits 26, 27, 28, and 29
- DIP3 - connects or disconnects the internal 4.7 Kohm pull-up resistor
- DIP4 - not used
The connected access control panel must accept the selected Wiegand format. Changing the Wiegand setting does not change the transmitter frequency, radio protocol, or credential format stored in the access control database.
3-Wire RF Bus Connection
The HIVE receiver processor also documents a 3-wire RF bus with power input, data output, and RF bus ground connections. The processor can be powered through the documented Wiegand port or RF port arrangement.
The RF bus is not documented as a Normally Open or Normally Closed dry-contact gate relay. Verify the connected access control architecture before replacing a standalone relay receiver with RECTSMULFRE1.
Facility Code and Receiver Memory Functions
The HIVE manual states that facility code checking is enabled when the receiver is shipped. The processor also provides a documented configuration for accepting any facility code while retaining the key code check.
The manual documents transmitter memory enrollment and deletion using the P1 programming button and DL2 programming LED. A numeric transmitter memory capacity is not published in the current RECTSMULFRE family specifications reviewed for this receiver.
For managed communities, commercial properties, storage facilities, or other controlled credential systems, verify the approved facility code before changing receiver settings.
Similar HIVE Receivers and RF Modules Are Not Automatically Interchangeable
- RECTSMULFRE1 uses the Model 1 RF slot options identified for this catalog configuration.
- RFMOD318-D should not automatically be replaced with RFMOD318-L.
- RFMOD296 is used for a 295 MHz receiver application despite the module SKU.
- RFMOD433 is not identified in the supplied RECTSMULFRE1 Model 1 slot map.
- A standalone HIVE relay receiver is not automatically interchangeable with the RECTSMULFRE Wiegand and RF bus architecture.
- Another RECTSMULFRE suffix should not be substituted without checking its module slot configuration and physical receiver label.
Features and Specifications
| Feature | Specification |
| Brand | Transmitter Solutions |
| Part Number | RECTSMULFRE1 |
| Product Type | Multi-frequency Wiegand receiver |
| Catalog Configuration | Model 1 |
| RF Module Slots | 2 |
| Left Slot Options | 318 MHz DoorKing-compatible or 418 MHz |
| Right Slot Options | 295 MHz, 318 MHz DoorKing-compatible, or 418 MHz |
| Compatible Left-Slot Modules | RFMOD318-D, RFMOD418 |
| Compatible Right-Slot Modules | RFMOD296, RFMOD318-D, RFMOD418 |
| RF Modules Required | 2 - sold separately |
| Wiegand Output | Selectable 26-bit or 30-bit |
| Wiegand Connections | DATA1 and DATA0 |
| Additional Data Connection | 3-wire RF bus |
| Input Power | 12-24 VAC/DC |
| Power Consumption | 24 mA |
| Maximum Output Current | 250 mA |
| IP Protection Description | Outdoor |
| Operating Temperature | -40F to 158F |
| Dimensions | 4 x 4 x 2 in |
| Output Type | Wiegand |
| Documented Weight | 2.3 ounces |
| RF Modules Included | No - two RF modules are required and sold separately |
| Standalone NO/NC Gate Relay | Not documented - Wiegand and 3-wire RF bus receiver architecture |
Package and RF Module Requirements
RECTSMULFRE1 is the Model 1 receiver configuration. Two RF modules are required and sold separately. Select one supported RF module for the left slot and one supported RF module for the right slot.
Transmitters, remote coax antenna kits, gate operator controls, and access control panels should not be assumed included. Confirm the two required RF modules and antenna configuration when building a complete receiver system.
Technician Note
The biggest ordering mistake on RECTSMULFRE1 is matching only the frequency. The Model 1 slot map matters, and the 318 MHz module identified for this configuration is RFMOD318-D. RFMOD318-L also says 318 MHz but is a different Linear-compatible protocol application. Match both RF modules to the correct slot, protocol, and transmitter system before ordering.
Before Ordering Checklist
- Verify the receiver part number is RECTSMULFRE1.
- Confirm the receiver uses the Model 1 slot configuration.
- Identify both transmitter systems the property must receive.
- Select a left-slot module from RFMOD318-D or RFMOD418.
- Select a right-slot module from RFMOD296, RFMOD318-D, or RFMOD418.
- Do not substitute RFMOD318-L for RFMOD318-D based only on 318 MHz frequency.
- Verify the exact transmitter frequency and radio protocol.
- For 295 MHz, verify the Sentex application and transmitter model.
- For 318 MHz, verify the DoorKing-compatible application and transmitter model.
- Confirm facility code requirements.
- Verify whether the access control panel requires 26-bit or 30-bit Wiegand.
- Confirm whether the installation uses Wiegand or the 3-wire RF bus.
- Check the physical RF module slots and processor labels.
- Verify antenna requirements for both installed RF modules.
- Confirm that two separately sold RF modules are included in the order.
Installation and Service Notes
The HIVE receiver manual states that unused RF card ports are supplied with jumper strips and that the jumper strips should only be replaced by proper radio cards. Match the installed modules to the RECTSMULFRE1 Model 1 slot configuration and the physical processor board connectors.
Verify receiver power, Wiegand format, facility code requirements, module position, and antenna connections before returning the access system to service. Do not change facility code or credential settings merely to force an unidentified transmitter to operate.
For damaged access control power circuits, unknown receiver wiring, or unclear Wiegand communication faults, use a qualified gate or access control technician. Do not bypass gate safety circuits, monitored entrapment protection, emergency access, or fire access functions while testing receiver operation.
Product Questions and Answers
Is RECTSMULFRE1 ready to use without RF modules?
No. RECTSMULFRE1 requires two RF modules, and both RF modules are sold separately. Select one supported module for each Model 1 receiver slot.
Which RF modules are compatible with the RECTSMULFRE1 left slot?
The Model 1 left slot is identified for RFMOD318-D in the 318 MHz DoorKing-compatible application or RFMOD418 at 418 MHz.
Which RF modules are compatible with the RECTSMULFRE1 right slot?
The Model 1 right slot is identified for RFMOD296 at 295 MHz, RFMOD318-D in the 318 MHz DoorKing-compatible application, or RFMOD418 at 418 MHz.
Can I use RFMOD318-L instead of RFMOD318-D in RECTSMULFRE1?
Do not automatically substitute RFMOD318-L. RECTSMULFRE1 Model 1 identifies RFMOD318-D for its 318 MHz application. RFMOD318-L is a separate Linear-compatible module designation, so matching 318 MHz frequency alone is not enough.
Can RECTSMULFRE1 receive every HIVE frequency at the same time?
No. RECTSMULFRE1 has two RF module slots and is configured with two supported radio modules. The Model 1 slot map identifies 318D or 418 for the left slot and 295, 318D, or 418 for the right slot.
Does RECTSMULFRE1 provide a dry-contact relay output directly to a gate operator?
The applicable RECTSMULFRE receiver documentation does not identify a standalone NO/NC gate relay. The processor provides Wiegand DATA1 and DATA0 outputs and a documented 3-wire RF bus connection. Verify the connected access control equipment before replacing a relay receiver.
Can RECTSMULFRE1 output both 26-bit and 30-bit Wiegand?
Yes. The HIVE receiver processor documentation identifies selectable 26-bit or 30-bit Wiegand output. The connected access control panel must accept the selected Wiegand format and credential configuration.
What should I verify before ordering Transmitter Solutions RECTSMULFRE1?
Verify the RECTSMULFRE1 receiver label, Model 1 slot configuration, two required RF module part numbers, transmitter frequencies and protocols, facility code, Wiegand format, RF bus or Wiegand wiring, antenna requirements, and package contents. Remember that both RF modules are sold separately.
