HySecurity MX3261-01, MANIFOLD, BRAKE, HCS 40, RIGHT
The HySecurity MX3261-01 is a right-hand brake manifold assembly for select HySecurity and Nice HySecurity HydraSwing hydraulic swing gate operators. It is commonly listed as MANIFOLD, BRAKE, HCS 40, RIGHT and as a Brake Manifold Assembly HydraSwing 40/40F/40 Twin RH.
The brake manifold is part of the hydraulic control system used to manage gate movement and stopping behavior in compatible HydraSwing actuator assemblies. In the correct HydraSwing application, the brake manifold works with the hydraulic cylinder, hose kit, brake valve, fittings, seals, pump pack, actuator hardware, and controller logic to help control movement under hydraulic load.
Current listings commonly describe MX3261-01 as including valves, fittings, and seals. HySecurity HydraSwing 40/40F actuator parts documentation lists MX3261-01 as the right-hand brake manifold assembly for HydraSwing 40 / 40F / 40 Twin applications and lists MX3261-02 separately as the left-hand brake manifold assembly. Because brake manifold orientation matters, this part should be selected by HySecurity part number, actuator hand, and parts diagram before ordering.
What This Brake Manifold Does
The MX3261-01 brake manifold assembly helps control hydraulic braking and movement behavior on compatible right-hand HydraSwing 40-series actuator assemblies. It is part of the hydraulic circuit that helps the actuator manage gate load, stopping, holding, and controlled movement depending on the operator configuration.
If the brake manifold, valve, fittings, or seals are leaking, contaminated, sticking, damaged, or installed on the wrong side, the gate may drift, move unevenly, stop poorly, chatter, bind, leak hydraulic fluid, or fail to hold position correctly. Similar symptoms can also be caused by worn cylinder seals, hose leaks, damaged pins, bad bearings, poor hinge alignment, low fluid, pump pack problems, valve adjustment issues, or a gate that is sagging or binding.
Compatible With
The HySecurity MX3261-01 is intended for select HySecurity / Nice HySecurity HydraSwing hydraulic swing gate operator applications where this right-hand brake manifold assembly is specified. Compatibility depends on the operator model, actuator hand, hydraulic cylinder assembly, hose routing, valve layout, fitting style, and current HySecurity parts documentation.
- Select HySecurity HydraSwing 40 right-hand actuator applications where the parts diagram lists MX3261-01
- Select HySecurity HydraSwing 40F right-hand actuator applications where the parts diagram lists MX3261-01
- Select HySecurity HydraSwing 40 Twin right-hand actuator applications where the parts diagram lists MX3261-01
- Select HydraSwing 40 / 40F / 40 Twin right-hand brake manifold repairs where the original assembly is marked, listed, or cross-referenced as MX3261-01
- Hydraulic brake manifold service where the installed manifold orientation, fittings, and valve configuration match MX3261-01
Do not assume MX3261-01 fits every HydraSwing, HydraLift, SlideDriver, SlideSmart, SwingSmart, StrongArm, HydraWedge, Smart DC, Smart Touch, or SmartCNX operator. Brake manifolds are model-specific and orientation-specific.
MX3261-01 vs. Related Brake Manifold Parts
HySecurity uses different brake manifold assemblies depending on operator model and actuator hand. MX3261-01 should not be treated as interchangeable with the left-hand version or with SlideDriver brake manifold parts.
- MX3261-01: Right-hand brake manifold assembly for select HydraSwing 40 / 40F / 40 Twin applications.
- MX3261-02: Left-hand brake manifold assembly for select HydraSwing 40 / 40F / 40 Twin applications, not the same part.
- MX3317-01: Right-hand brake manifold assembly for select HydraSwing 80F / 150 applications, not the same part.
- MX3317-02: Left-hand brake manifold assembly for select HydraSwing 80F / 150 applications, not the same part.
- MX000137: SlideDriver 30F / 40 brake kit, not the same part.
- MX000143: SlideDriver braking manifold / brake kit for select SlideDriver 50VF2/3, 80, and 200 applications, not the same part.
- MX000234: Related HydraSwing brake valve reference, not the full brake manifold assembly.
The right-hand and left-hand HydraSwing brake manifolds should be matched by the actuator layout and parts diagram. A manifold that looks similar may have different port orientation, hose routing, valve placement, fitting arrangement, or mounting layout.
Right-Hand Orientation Warning
MX3261-01 is the right-hand brake manifold assembly. Confirm the actuator hand before ordering. On dual or twin swing gate systems, left-hand and right-hand references can be easy to confuse, especially if you are looking at the gate from the wrong side or if the operator has been previously serviced.
When in doubt, compare the installed manifold, hose routing, port positions, valve orientation, and HySecurity actuator diagram. Do not order the right-hand manifold to replace a left-hand assembly unless HySecurity documentation specifically confirms the match.
Related HydraSwing 40 / 40F Actuator Parts
HydraSwing brake manifold repairs often involve nearby hydraulic and mechanical parts. Check the complete actuator assembly before deciding whether the brake manifold is the only part needed.
- MX3261-02: Left-hand brake manifold assembly for HydraSwing 40 / 40F / 40 Twin applications
- MX000234: Brake valve used in select HydraSwing hydraulic circuits where specified
- MX3545: Hose kit with fittings for select HydraSwing 40 / 40F applications where specified
- MX3546: Position-sensing cylinder kit for select HydraSwing 40 / 40F / 40 Twin primary actuator applications
- MX3547: Cylinder kit without sensor for select HydraSwing 40 / 40F Twin secondary actuator applications
- MX3058: Cylinder pin used in select HydraSwing actuator assemblies where specified
- MX000770: Tapped 1.25-inch bearing used in select HydraSwing 40 / 40F actuator assemblies
- MX3531-04: Standard chassis cover for select HydraSwing 40 / 40F applications where specified
Not Intended For
- Universal hydraulic brake manifold replacement
- Left-hand HydraSwing 40 / 40F / 40 Twin applications that require MX3261-02
- HydraSwing 80F / 150 applications that require MX3317-series brake manifold assemblies
- SlideDriver brake manifold or brake kit applications that require MX000137, MX000143, or another SlideDriver brake assembly
- Replacing only the brake valve if the parts diagram calls for an individual valve repair
- Replacing the hydraulic cylinder kit, hose kit, bearing, pin, pump pack, or controller board unless those parts are separately ordered
- Correcting gate drift or poor stopping caused by gate hinge problems, hydraulic cylinder wear, hose leaks, low fluid, bad actuator alignment, or mechanical binding without diagnosis
- Opening or removing hydraulic components from a pressurized circuit
Important Compatibility Warning
MX3261-01 should be selected by HySecurity part number, operator model, actuator hand, and hydraulic diagram. A brake manifold with the wrong hand or port orientation may not connect correctly and may cause hydraulic control problems.
If the brake manifold failed because of contaminated hydraulic fluid, water intrusion, damaged fittings, bad hose routing, cylinder seal failure, or mechanical side-loading, replacing only the manifold may not correct the root issue. Inspect the actuator, hoses, cylinder, pins, bearing, gate hinges, and hydraulic fluid before returning the operator to service.
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | HySecurity / Nice HySecurity |
| Part Number | MX3261-01 |
| Alternate Part Formatting | MX326101, sometimes used without the dash in distributor or internal references |
| Product Type | Hydraulic brake manifold assembly |
| Common Description | MANIFOLD, BRAKE, HCS 40, RIGHT |
| Alternate Description | Brake Manifold Assembly, HydraSwing 40/40F/40 Twin RH |
| Hand / Orientation | Right-hand / RH |
| Documented Operator References | Select HydraSwing 40, HydraSwing 40F, and HydraSwing 40 Twin applications where the parts diagram lists MX3261-01 |
| System Area | Hydraulic actuator / brake manifold circuit |
| Common Included Components | Current listings commonly state that valves, fittings, and seals are included; verify current supplier package before publishing as guaranteed |
| Related Left-Hand Assembly | MX3261-02 is the related left-hand brake manifold assembly and is not the same part |
| Selection Method | Match by HySecurity part number, actuator hand, operator model, hydraulic diagram, hose routing, port orientation, and valve/fitting layout |
| Not Included Unless Listed | Hydraulic cylinder, hose kit, pump pack, hydraulic fluid, actuator pins, tapped bearing, chassis cover, controller board, and gate hardware unless separately listed |
Also Known As / Related Part Numbers
- MX3261-01
- MX326101
- HySecurity MX3261-01
- Nice HySecurity MX3261-01
- HySecurity MANIFOLD, BRAKE, HCS 40, RIGHT
- HySecurity Brake Manifold Assembly HydraSwing 40/40F/40 Twin RH
- HySecurity HydraSwing 40 brake manifold right hand
- HySecurity HydraSwing 40F brake manifold right hand
- HySecurity HydraSwing 40 Twin brake manifold right hand
- HySecurity HCS 40 right brake manifold
- HySecurity RH brake manifold assembly
- HYS-MX3261-01, related distributor SKU format
- MX3261-02, related left-hand HydraSwing 40/40F/40 Twin brake manifold assembly, not the same part
- MX3317-01, related right-hand HydraSwing 80F/150 brake manifold assembly, not the same part
- MX3317-02, related left-hand HydraSwing 80F/150 brake manifold assembly, not the same part
- MX000234, related HydraSwing brake valve, not the same as the full manifold assembly
- MX000137, related SlideDriver 30F/40 brake kit, not the same part
- MX000143, related SlideDriver braking manifold / brake kit, not the same part
Related Parts and Accessories
- mx3261-02-left-hand-brake-manifold-hydraswing-40-40f.html">HySecurity MX3261-02 left-hand brake manifold assembly for HydraSwing 40 / 40F / 40 Twin applications
- mx000234-braking-valve-cartridge-10-1.html">HySecurity MX000234 brake valve where the individual brake valve is being serviced
- HySecurity MX3545 hose kit with fittings for select HydraSwing 40 / 40F applications
- mx3546-position-sensing-cylinder-kit-hydraswing-40-40f.html">HySecurity MX3546 position-sensing cylinder kit for select HydraSwing 40 / 40F / 40 Twin primary actuator applications
- mx3547-cylinder-kit-without-sensor-hydraswing-40-40f.html">HySecurity MX3547 cylinder kit without sensor for select HydraSwing 40 / 40F Twin secondary actuator applications
- mx3058-cylinder-yoke-pin-hydraswing.html">HySecurity MX3058 cylinder pin where the actuator pin is worn or damaged
- mx000770-1-25-inch-tapped-bearing-pillow-block.html">HySecurity MX000770 tapped 1.25-inch bearing where the actuator bearing is worn or seized
- HySecurity MX3531-04 standard chassis cover for select HydraSwing 40 / 40F applications
- Hydraulic fluid specified by the current HySecurity operator manual
- Gate hinge, post, bracket, and mechanical alignment parts where gate movement is overloading the actuator
Technician Note
Before replacing the brake manifold, verify whether the issue is actually in the manifold assembly. Gate drift, poor stopping, uneven movement, and hydraulic leakage can also come from the hydraulic cylinder, brake valve, hose kit, fittings, low fluid, contaminated fluid, worn pins, bad bearings, poor hinge alignment, or a gate that is binding.
Pay close attention to right-hand versus left-hand orientation. MX3261-01 is the right-hand brake manifold. The related left-hand version is MX3261-02. Hose routing, port layout, and valve placement must match the installed actuator assembly.
Before Ordering, Confirm
- Confirm the needed HySecurity part number is MX3261-01.
- Confirm the original part is listed as MANIFOLD, BRAKE, HCS 40, RIGHT.
- Confirm the operator is a compatible HydraSwing 40, HydraSwing 40F, or HydraSwing 40 Twin application.
- Confirm the actuator hand is right-hand / RH.
- Confirm the parts diagram lists MX3261-01 for the brake manifold location.
- Confirm the repair does not require MX3261-02, the left-hand version.
- Confirm the hose routing, port orientation, valve layout, fittings, and seals match the installed manifold.
- Confirm the issue is not caused by the hydraulic cylinder, hose kit, brake valve, pump pack, low fluid, contaminated fluid, actuator pin, bearing, gate hinge, or gate alignment problem.
- Confirm whether valves, fittings, seals, hardware, instructions, or hydraulic fluid are included or must be ordered separately.
Installation and Service Notes
Hydraulic brake manifold service should be performed with the operator disabled, the gate secured, and the hydraulic circuit handled according to the current HySecurity service procedure. Do not remove hydraulic valves, hoses, or fittings from a pressurized circuit.
Keep the manifold ports, fittings, and hose ends clean during service. Dirt or metal particles inside the hydraulic circuit can damage valves, seals, cylinders, pump components, and fittings. After installation, check hydraulic fluid level, inspect for leaks, verify smooth actuator movement, confirm proper stopping/holding behavior, and test all monitored safety devices before returning the gate to service.
Professional Advisory
Brake manifold replacement can affect hydraulic braking, stopping, and holding behavior on a heavy swing gate. A qualified HySecurity gate technician should handle this repair if the operator has repeated hydraulic leaks, unknown prior repairs, contaminated fluid, gate drift, poor stopping, or unclear left/right actuator orientation.
Do not bypass covers, guards, limits, monitored entrapment protection, photo eyes, safety edges, hydraulic controls, disconnects, or controller protections to make the gate run. The hydraulic system, mechanical assembly, and safety devices should be repaired correctly and fully tested before the operator is returned to service.
Product Questions & Answers
What is the HySecurity MX3261-01 used for?
The HySecurity MX3261-01 is a right-hand brake manifold assembly used in select HydraSwing 40, 40F, and 40 Twin hydraulic swing gate operator applications.
Is MX3261-01 the right-hand or left-hand brake manifold?
MX3261-01 is the right-hand / RH brake manifold assembly. The related left-hand version is MX3261-02.
What operators is MX3261-01 commonly associated with?
MX3261-01 is commonly associated with select HydraSwing 40, HydraSwing 40F, and HydraSwing 40 Twin actuator applications where the parts diagram confirms fitment.
Does MX3261-01 include valves, fittings, and seals?
Current listings commonly state that MX3261-01 includes valves, fittings, and seals. Verify current supplier package contents before ordering if those items are required.
Is MX3261-01 the same as MX3261-02?
No. MX3261-01 is the right-hand brake manifold assembly. MX3261-02 is the related left-hand brake manifold assembly. They should not be treated as interchangeable.
What should I check before replacing MX3261-01?
Check actuator hand, hose routing, port orientation, valve layout, hydraulic cylinder condition, hose leaks, brake valve condition, fluid level, actuator pins, bearings, gate hinges, and gate alignment before replacing the brake manifold.
