AES ETRANS100, eLoop Transceiver - 2x Relay Output N/O + N/C - LED Indicators
The AES ETRANS100 is a two-channel transceiver for select AES e-Loop, e-Trans, wireless keypad, remote transmitter, and access control applications. It is used as the receiving and relay-output side of a compatible AES wireless system.
In a properly configured installation, the ETRANS100 can receive signals from compatible AES e-Loops, remotes, wireless keypads, and supported entry devices, then activate one of its relay outputs for an approved gate operator, door controller, or access control input.
This is the transceiver-only product. It should not be confused with complete transmitter kits, keypad kits, long-range kits, e-Loop detector kits, antenna kits, or complete gate access systems. Order by exact AES part number, relay requirements, input voltage, supported device type, and system compatibility.
What This Two-Channel Transceiver Does
The ETRANS100 provides two-channel receiver/transceiver functionality for compatible AES wireless devices. It is commonly selected where the installation needs two separate relay outputs, two channel assignments, LED-based status feedback, and a compact receiver/transceiver without the LCD menu display found on the ETRANS200.
Depending on the programmed device and relay assignment, the ETRANS100 may be used for gate open commands, exit or presence detection relay outputs, keypad access, remote transmitter activation, or auxiliary access control functions where the controlled equipment supports the relay input.
This transceiver does not move a gate or door by itself. Final operation depends on proper power, compatible AES wireless devices, relay wiring, antenna placement, receiver programming, gate operator input setup, access control wiring, and required safety devices.
Compatible With
Use the AES ETRANS100 only where AES documentation, the system design, product label, or supplier cross-reference confirms compatibility. Compatibility depends on the AES wireless platform, device type, frequency, relay requirement, antenna setup, firmware or generation, and controlled equipment.
- Select AES e-Loop systems requiring an ETRANS100 / E-TRANS-100 two-channel transceiver
- Select AES e-Trans wireless receiver/transceiver applications requiring two relay outputs
- Select AES E-TX transmitter fob applications where the receiver documentation supports ETRANS100 programming
- Select AES E-REMOTE applications where the receiver/transceiver supports the required button or lock/unlock function
- Select AES EKPD wireless eKeypad applications where the keypad is paired to an ETRANS100 transceiver
- Select AES EKPD-KT kit applications where the ETRANS100 is the included or required transceiver
- Select AES e-Loop detector applications where ETRANS100 is used as the receiving transceiver for exit or presence operation
- Gate, door, and access control applications where two relay outputs are required and the relay ratings are suitable for the controlled equipment
- Repairs or replacements where the original transceiver is marked, listed, or cross-referenced as ETRANS100 or E-TRANS-100
Important Compatibility Warning
The AES ETRANS100 is not the same as ETRANS50 or ETRANS200. The ETRANS50 is commonly used for single-relay applications, the ETRANS100 is a two-channel LED-indicator transceiver, and the ETRANS200 is the LCD transceiver with larger menu-based functions and higher device storage references.
Relay terminal descriptions should be verified before wiring. The ETRANS100 manual commonly lists relay terminals as COM and N/O connections x 2 relays, while some product descriptions and kit references mention N/O + N/C contacts. Always check the physical terminal markings, product label, and current AES manual before connecting the relay to a gate operator, door controller, lock interface, or access control input.
Do not use the relay output to switch high-voltage loads directly. The relay should be connected only to an approved low-voltage control input or approved interface device. Never bypass monitored safety devices, photo eyes, safety edges, fire access wiring, stop circuits, or gate operator entrapment protection to make the transceiver activate equipment.
Similar AES Parts That Are Not Automatically Interchangeable
- AES ETRANS100: Two-channel LED-indicator transceiver; this is the transceiver-only item described on this page.
- AES E-TRANS-100: Alternate naming format for ETRANS100; verify the physical package label and supplier SKU.
- AES ETRANS100-US: Possible regional SKU format; verify before publishing the suffix on the live page.
- AES ETRANS50: Single-relay transceiver; not the same as ETRANS100.
- AES ETRANS200: LCD transceiver with different programming and storage features; not the same as ETRANS100.
- AES ETRANS100-TX-KIT: Kit version that may include ETRANS100 plus E-TX fobs and antenna; not the same as transceiver-only.
- AES ETRANS100-TX-LR-KIT: Long-range kit version with antenna and remotes; not the same as transceiver-only.
- AES EKPD-KT: Wireless keypad kit that includes eTrans100 where supplied as listed; not the same as the transceiver-only item.
- AES E-TX: Four-button transmitter fob; not the same as ETRANS100.
- AES E-REMOTE: Three-channel transmitter with lock/unlock function; not the same as the transceiver.
- AES ANT-4 / ANT-30: Antenna accessories; not the same as the transceiver.
- AES e-Loop detectors: Vehicle detection modules; not the same as the ETRANS100 receiving transceiver.
Not Intended For
- Use as a complete gate operator, door operator, intercom, keypad, or access control system by itself
- Replacement for an e-Loop detector, safety loop, photo eye, safety edge, or monitored entrapment device
- Use as a transmitter fob, wireless keypad, diagnostic remote, diagnostic light, or antenna accessory
- Use where an ETRANS50, ETRANS200, transmitter kit, keypad kit, or long-range kit is specifically required
- Direct switching of high-voltage circuits, magnetic lock power, strike power, motor wiring, or unsafe loads without an approved relay interface
- Solving poor range caused by weak transmitter batteries, bad antenna placement, metal obstruction, interference, low receiver power, or incorrect programming without proper diagnosis
- Bypassing access permissions, fire access equipment, monitored photo eyes, safety edges, gate operator safety circuits, stop circuits, or required entrapment protection
Features & Specifications
| Feature / Specification | Details |
| Manufacturer | AES / AES Global |
| Part Number | ETRANS100 |
| Alternate Part Number Format | E-TRANS-100; verify package label and supplier SKU before ordering |
| Possible Regional SKU | ETRANS100-US may appear in some AES catalog references; verify before publishing the suffix |
| Product Type | Two-channel receiver / transceiver for AES e-Loop and e-Trans wireless systems |
| Display / Indicators | LED indicators; no LCD display on this model |
| LED Reference | Code LED is commonly listed as blue, LP/RM LEDs as red, and Menu LED as yellow; verify current product label or manual |
| Input Voltage | 10-28V AC/DC, where specified by AES documentation; verify current label before wiring |
| Current Draw | 12 mA standby / 20 mA active, where specified by AES documentation |
| Frequency | 433.39 MHz |
| Bandwidth | 250Hz, where specified by AES documentation |
| Transmitting Power | Less than 10mW, where specified by AES documentation |
| Channel Count | Two channels |
| Channel Assignment Reference | CH1 is commonly associated with Relay 1 and CH2 is commonly associated with Relay 2; verify programming instructions before setup |
| Relay Outputs | 2 relay outputs; verify terminal markings before wiring |
| Relay Terminal Verification | User-supplied description lists N/O + N/C. AES manual references commonly list COM and N/O connections x 2 relays. Confirm the physical terminals and current manual before installation. |
| Relay Contact Rating | 1-amp contact rating, where specified by AES documentation; verify before wiring to controlled equipment |
| Coding Support | Supports coding compatible AES e-Loops, remotes, and keypads where supported by the installed system |
| Lock / Unlock Note | Manual references indicate E-REMOTE lock/unlock behavior may latch or unlatch the relay when coded to a channel; verify programming before use |
| Included Components | ETRANS100 transceiver only unless the product listing or package states otherwise |
| Not Included | E-TX remotes, E-REMOTE, EKPD keypad, e-Loop detector, ANT-4, ANT-30, power supply, gate operator, wiring, conduit, access controller, or complete kit unless specifically stated |
Also Known As / Related Part Numbers
- AES ETRANS100
- ETRANS100
- AES E-TRANS-100
- E-TRANS-100
- AES Global ETRANS100
- AES Global E-TRANS-100
- Nice AES ETRANS100
- AES e-Trans 100 Two-Channel Transceiver
- AES eLoop Transceiver with LED Indicators
- AES e-Loop Two-Channel Receiver
- AES e-Loop Two-Channel Transceiver
- AES 433.39 MHz Two-Channel Transceiver
- AES Transceiver with 2 Relay Outputs
- AES ETRANS100-US, possible regional SKU format; verify physical package label before publishing with the suffix
- AES-ETRANS100
- AES-E-TRANS-100
- ETRANS-100, possible search variation only; verify exact part number before ordering
- ETRANS100LED, possible search variation only; verify exact part number before ordering
- HYS-ETRANS100, related distributor-style SKU format only; verify seller SKU before ordering
- ETRANS50, related single-relay transceiver; not the same as ETRANS100
- ETRANS200, related LCD transceiver; not the same as ETRANS100
- ETRANS100-TX-KIT, related kit version; not the same as transceiver-only
- ETRANS100-TX-LR-KIT, related long-range kit version; not the same as transceiver-only
- EKPD-KT, related wireless keypad kit with eTrans100; not the same as transceiver-only
Related Parts and Accessories
- AES E-TX, 4-button transmitter fob compatible with select AES e-Loop transceiver products
- AES E-REMOTE, 3-channel transmitter with lock/unlock function for compatible receiver applications
- AES EKPD, wireless eKeypad only; pairs with compatible receiving equipment where supported
- AES EKPD-KT, wireless eKeypad kit with eTrans100 transceiver where supplied as listed
- AES ETRANS100-TX-KIT, related transmitter kit version; verify contents before ordering
- AES ETRANS100-TX-LR-KIT, related long-range kit version; verify antenna and remote contents before ordering
- AES ANT-4, puck-style 433 MHz antenna for select AES wireless systems where supported
- AES ANT-30, high-gain 433 MHz antenna for select long-range AES wireless systems where supported
- AES e-Loop detector models, where the ETRANS100 is used as the compatible receiving transceiver
- Approved low-voltage wiring, conduit, enclosure, surge protection, and relay interface parts where required by the installation
Technician Note
If an ETRANS100 system is not activating the gate, troubleshoot both the wireless side and the relay-output side. Check transmitter or keypad programming, e-Loop coding, antenna connection, receiver power, channel assignment, relay output wiring, access control input, gate operator input settings, and the operator status before replacing the transceiver.
If the ETRANS100 relay LED indicates activity but the gate does not move, the transceiver may not be the problem. Check relay assignment, relay wiring to the operator, stop circuit, safety circuit, fire access input, access control terminals, and operator programming.
If range is poor, inspect antenna placement before replacing electronics. Metal cabinets, low antenna mounting, poor line of sight, damaged coax, weak transmitter batteries, nearby radio noise, and incorrect antenna selection can make a working transceiver appear unreliable.
Before Ordering, Confirm
- The required part number is ETRANS100 or E-TRANS-100.
- The installation needs the two-channel LED-indicator transceiver only, not a transmitter kit, keypad kit, long-range kit, or e-Loop detector kit.
- The connected AES devices are compatible with the ETRANS100 wireless platform.
- The system requires the ETRANS100 feature set rather than ETRANS50 or ETRANS200.
- The input voltage available at the site matches the listed 10-28V AC/DC requirement.
- The controlled equipment has approved low-voltage inputs for the relay outputs.
- The relay terminal requirements are confirmed, especially whether the site needs N/O only, N/C, or COM/N/O terminals.
- The relay contact rating is suitable for the gate, door, or access control input.
- The antenna connector, antenna type, and mounting location are suitable for the installation.
- The issue is not caused by transmitter batteries, missing programming, bad antenna placement, relay wiring, low power, or gate operator input problems.
- The package contents are confirmed, especially whether antennas, remotes, mounting hardware, instructions, or power accessories are included.
Installation and Service Notes
- Install and program the ETRANS100 only on systems you are authorized to service.
- Follow AES instructions for coding remotes, e-Loops, keypads, and supported entry devices into the transceiver.
- Power the ETRANS100 only within the voltage range and wiring method shown on the current product label or manual.
- Verify relay terminal markings before wiring. Do not assume N/O, N/C, or COM terminal layout without checking the physical transceiver.
- Do not connect relay outputs directly to high-voltage loads, motor wiring, lock power, or unsupported operator terminals.
- Use the LED indicators to confirm coding and relay activity, but do not rely on LEDs as the only troubleshooting step.
- Mount the transceiver and antenna where the radio path is as clear as practical and wiring is protected.
- After setup, test each programmed device, relay output, access command, and gate or door response.
- Do not bypass monitored gate safety inputs, photo eyes, safety edges, stop circuits, emergency access equipment, fire access wiring, access permissions, or required entrapment protection during testing.
Professional Advisory
A qualified gate, access control, or low-voltage technician should install or service the AES ETRANS100 when it is connected to a gate operator, automatic door, magnetic lock, electric strike, intercom, telephone entry system, fire access system, or monitored safety circuit. Relay wiring, gate input configuration, channel assignment, and safety-device interaction should be tested carefully. Do not bypass access control permissions, emergency access requirements, monitored safety devices, or gate operator protections to make the system operate.
Product Questions & Answers
What is the AES ETRANS100 used for?
The AES ETRANS100 is used as a two-channel transceiver for compatible AES e-Loop, e-Trans, wireless keypad, remote transmitter, and access control applications.
Does the AES ETRANS100 include remotes or an antenna?
No. ETRANS100 is the transceiver-only item unless the product listing specifically states otherwise. E-TX fobs, E-REMOTE transmitters, ANT-4, ANT-30, keypads, and e-Loop detectors are separate items or part of separate kits.
How many relay outputs does the AES ETRANS100 have?
The ETRANS100 is a two-channel transceiver with 2 relay outputs. Relay terminal type should be verified on the physical transceiver because some references list COM and N/O connections while other descriptions mention N/O and N/C output capability.
What voltage does the AES ETRANS100 use?
The AES ETRANS100 is commonly specified for 10-28V AC/DC input. Always confirm the current product label and installation manual before wiring power.
Does the AES ETRANS100 have an LCD display?
No. The ETRANS100 uses LED indicators for coding and status reference. The AES ETRANS200 is the related LCD transceiver model.
Is AES ETRANS100 the same as ETRANS50?
No. ETRANS100 is the two-channel LED-indicator transceiver. ETRANS50 is a related single-relay transceiver and should not be treated as the same part.
What should I check before ordering AES ETRANS100?
Confirm the exact ETRANS100 or E-TRANS-100 part number, transceiver-only requirement, voltage input, relay terminal type, relay rating, compatible AES devices, antenna needs, package contents, and whether the job requires a kit instead.
